e2-Live Home Automation RP-20F AVhome BOX Instruction manual Edit by Amos /20150810 0
e2-Live Home Automation Index E2-LIVE HOME APPLIANCES INTEGRATOR RP SERIES ...............................................................................................3 HARDWARE ................................................................................................................................................................................4 Front panel.............................................................................................................................................
e2-Live Home Automation Version Description Date Ver. Revised contents Software Version 20130709 REV 1.2 Prototype 070803 2013/7/16 REV 1.2 Prototype 071002 2013/07/18 REV 1.2 Prototype 071805 2013/07/23 REV 1.2 Prototype 071805 2013/10/29 REV 1.5 Formal ver.
e2-Live Home Automation e2-Live AVhome BOX (RP family) Functions / Type RP-05 RP-10N RP-20F Numbers of IR button 29 buttons 7 HA / 203buttons 7 HA /203 buttons Power status detection no no Yes, must be used with iPower or related IR output mode 2 wires IR output 360 degree IR output 360 degree+7 wires specify separate output Number of order/Macro 60 commands /10 macros 60 commands 24 scenarios, 60 commands/ scenario /10 macros (lighting & curtain control is available) Macro setting e
e2-Live Home Automation Hardware Front Panel 9 pieces of infrared emission LED (First control point) 2 pieces of infrared emission LED can be fine tune up/down or left/right (First control point) IR in：IR signal input, from your remote control of appliances. Status：Blue color, IR emission indicator (Indicator will flash while in learning IR code) Tx/Rx：Red color, RF wireless emission and received indicator. Rear Panel No.
e2-Live Home Automation Accessary Extended IR emit wire X 2(1.8m) USB connector wire to PC DC Adaptor (5V 1.
e2-Live Home Automation IR individual areas control RP-20F IR – total 7 areas Point 1: Surround infrared emission on top cover, has the same time emission with the point 1 port of the rear panel Surround emission Point 1 wired IR output Up / down, left / right, Emission angle can be fined tune Applications: Surround infrared LED has 360 degree emit to control whole of home appliances of open space in the same room.
e2-Live Home Automation Corresponding to the position of the remote control and setting software RC-09 Operating device + device + action = first point emission For example: TV TV Power, the RP-20 will sent emission by the first point of IR infrared signal . RP-20 software Control Validation / infrared appliances scenarios set / Appliances After pointing device button and choose "Point 1" emission. The RP-20 will send an infrared signal from the first IR emission point.
e2-Live Home Automation Point 2 ~ 7 are wired control 1. Appliances in Audio/Video cabinet tank: IR signals cannot penetrate the veil, if the device is placed in the cabinet tank, IR emission lines need to be extended to the cabinet in order to control 2. Devices are placed on the range of control IR extension wire can help to solve the problem of IR emit signal been cut off by shelter. 3.
e2-Live Home Automation How to operate the RP-20F control points individually RP-20F support individual IR emission, following devices can be control individually.
e2-Live Home Automation 1st press device, example , 2nd press 1st press device, example 2nd press , 3rd press , 3rd press ,then point 2 of IR emit , then point of 3 IR emit Use itouch (use with PC-09W or PC-09I, Wi-Fi emission) Point 2 emit (Same as RC-09, number 11) Point 3 (same as RC-09, Number 12) Operation same as RC-09。 Select device first, example , 2nd press , then all points of IR emit Select device first, example , 2nd press , 3rd press , then point 1 emit Select device first, ex
e2-Live Home Automation RP-20 Home Control Center 1. Please insert the installation CD, it is in the packaging box 2. Installation CD will auto run and open its homepage Software installation of RP-20 Click RP-20 executive program to auto run installation During installation the program may ask you to download the update system of framework, Each computer may have different necessary, please make sure your PC can be connected to network, RP-20F will install necessary program automatically.
e2-Live Home Automation RP-20 make sure connect to PC Remove the connector wire out of the package, connect RP-20 and PC Support PC system Windows XP Windows 7 (32/64 位元) Windows 8 (32/64 位元) + + Note：By using this connector wire to connecting RP-20 with PC to setting any parameters through your PC, does not require a transformer, RP-20 can be powered by PC Power source of PC, but if the setting is completed, installed in a fixed location, Please use the power adapter attached with the package to ensure
e2-Live Home Automation With an exclamation point, which means that the device can not be used, you need to install the driver. If you turn on RP-20, no clickable COM on pull-down menu of the right connections,the USB device is not properly enabled, it can not be connected. If you have any of the above circumstances occur, which means that you need to install RP-20F USB driver manually. take the CD out of the package insert into the CD slot, click USB driver to install.
e2-Live Home Automation After installation, please re-plug RP-20F USB once again, let the computer detect again. Finish Please choose 目前 the same COM取 RP-20 position 得的連線 for RP-20 COM 位 Open RP-20 will automatically appear maybe several connectable positions of COM. Please go to Device Manager to confirm the correct position of the COM, in order to successfully communicate with RP-20.
e2-Live Home Automation RP-20 software Connection Before RP-20 be open, please use USB wire connect RP-20 with PC, then COM port will be detected Home page setting If RP-20 AVhome Box had been connected to PC, then press Detect to automatically find out the connection of COM port.
e2-Live Home Automation Functions ID Setting Here will display the instructions Input 4 digital ID code, Press “wright” to input (0000~9999) When enter impleted 4 digital numbers, it will be field with “0” in front of your input numbers, such as input” 123”, the actual ID would be “0123”, input “66”, would be “0066” When writing success, RP-20 AVhome Box will prompt buzzer and LED.
e2-Live Home Automation Setting ID of iPower (PS-301 or PS-302) RP-20 work together with iPower to make sure the devices’s power is ON or OFF. This special designed is to solve bland power ON/OFF control on scenario mansging. Perform this function, please plug your home appliances in smart socket of iPower. Use this page, you can setting the location of remote control. Note: This setting must work with our smart socket iPower, specify the selected button of iPower to get into learning mode.
e2-Live Home Automation IR Learning Preparatory actions before the operation： Tools needed: the original remote control of home appliances z Make sure your home appliances is in the status of energized (Through the phone to activate the camera function), facing camera of your smart phone, press any button of any remote controller, if the emitting light of your remote controller can be seen, that means the emission of remote controller is in normal situation.
e2-Live Home Automation 29 action button will enable the buttons to have the function of press 3. Press corresponding function of a button on, such as ： Buzzer LED Short Bi Flash Blue LED 4. Pick up your remote controller of appliances, facing emission LED to RP-20 ”IR in” then press down the power button to input power ON/OFF code.
e2-Live Home Automation 5. Repeat step 2~3 to continually to learn remote signal into RP-20 Situations of need to re-learn 1.After input IR signal, if Buzzert One long, one short Red flash twice Please re-press the button of appliance IR signal 2. After input IR signal, when you hear of LED Blue stable on Buzzer Short Bi three times LED Slowly flashing blue LED ….
e2-Live Home Automation Leave Learning Mode 1.Completed learning all of your appliances IR, please press “Stop Learning” for interup learning mode.” 2.
e2-Live Home Automation RP-20 can specify a different signal IR emitting region If you just want to verify that learning is successful, select "All emit” Sequence of operations: 1. Select equipment 2. Select "All emit" 3. Press the right action key 4. Make sure the corresponding buttons are successfully remote control, if there is not, please repeat the learning sequence.
e2-Live Home Automation Scenario Setting Edit lighting & curtain Editable Setting 24 Macros Devices Light 01 Light 02 Light 03 Light 04 Light 05 Curttain (specify) Keys 01~12 Actions Lighting ON/OFF ALL ON/ALL OFF RP-20AVhome Box1~24 Macros ID can be specify difference with RP-20 to corresponding lighting, curtain, and iPower. Please note that in use of any remote control device operation, remote controller ID must same as RP-20, not same as scenario.
e2-Live Home Automation Edit Home Appliances Interval: (only appliance action can be inserted interval) from 1 to 60 seconds, up/down to choose or key in the wanted numbers of seconds, maxmum is 60 seconds, more than 60 seconds are limited to 60 seconds. 0 second and 1 second do not have the significant effect.
e2-Live Home Automation Scenario tool After data selected, press here for adding one new command on the bottom of the list Select and move edited data up and down for smooth scenario control Recovery a previous action, you can always forward recovery Click to delete a selected single data row Save the current page of single scenario setting Clearn up memory Save all 24 scenario setting, will take a little time, please be attention to see front RxTx red LED, Stop flash means save compled Still flashin
e2-Live Home Automation According to the following steps, you could insert one action into scenario edit setting program planned well your action conditions, press Click this edit setting row, use to add in this edit setting row to move this edit setting row to where you want be placed Save Single scenario storage, only saving the current scenario of the screen All scenario storage, saving all of the scenarios from No.1 ~ No.
e2-Live Home Automation If TV is always ON, then RP-20 will send out the aommand to turn off the TV No detect：Don＇t care the status of appliances power ON or OFF, just perform the command of scenario. Scenario Vaidation setting After completed editting and storage of scenario, suggest to confirm the correctness and fluency of perform of scenario, if there is any problem of action then you could easy adjust and fine tune on setting page.
e2-Live Home Automation function. 4. RP-20 provide different ID for lighting and curtain control, please make sure and input the scenario’s ID before saving, this ID would be stored to RP-20 while saving. 5. After scenario storage, please use Control Verification/Scenario Verification to test immediately to make sure your setting is correct and adjust instantly. Scenario remote controller.
e2-Live Home Automation Control Verifications RP-20 software : The purpose of control verification is to make sure its works after IR learning and scenario setting, it also provide remote control of lighting and curtain, it could be remote control all function of e2-Live via this software. In operation, the network connections of RP-20 or PC must be maintained.
e2-Live Home Automation Appliances Infrared control Select device--ÆIR emission location--ÆAction button Scenario verifications Press button of scenario 01~24，RP-20 will be executed immediately, be careful to operate, 。 during operation of scenario, it does not accept others remote commands again.
e2-Live Home Automation Backup Setting Backup recovery For RP-20 to read out the backup setting data The information of RP-20 software could backup or recovery are as follow： 1. Remote ID 2. Infrared learning data 3. RP-20 AVhome Box scenario settings The default storage path, suggest do not changed Press File names can be modified in either Chinese or English Its takes about 2 or 3 minutes to backup or recovery.
e2-Live Home Automation Backup purpose 1. If there is any probrom of RP-20, then you could revovery back to initial status 2. Copy to another RP-20 Recovery： ID & Scenario For RP-20 software setting is finished【Scenario & ID data】, You can save as a file to PC RP-20 can save a single or all of the scenarios to PC for storage, and read back to RP-20 by Input. Purpose of output data of scenario 1. Save for backup file 2.
e2-Live Home Automation Output: Save the current scenario settings to PC for later revised using (could be one or more) Output file The default storage path, suggest keep the path Press File names can be modified in either Open/Close/Muting RP-20 Open Close In IR learning, RP-20 is recommended to open the buzzer can help confirm the operation action Edit by Amos /20150810 33
e2-Live Home Automation RP-20 host has received. After editing operation is completed with the relevant settings, you can choose to turn off the buzzer About Restore factory settings： Press and then sure to Buzzer Long Bi , IR learning data and scenario setting will be cleare. Please be confirm before execution.
FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
