Installation & Assembly

ManualsBrandsTech Lighting ManualsDecorGia Bathroom / Vanity Mirror

GP I :ENERAL RODUCT NFORMATION

Suitable for damp locations.

Install the Fixtures

Ensure that the electrical box is located behind the mirror location.

-For multiple mirror installations, an electrical box must be present behind the mirror which is the center of the group.

-For multiple mirror installations with 600 lms/ft, two electrical boxes must be present behind each outer mirror to support

the additional driver.

Using the provided cardboard mirror template and a fixture; level, measure, and mark the location of mirror(s) and fixtures.

CAUTION - RISK OF FIRE

This product must be installed in accordance with the

applicable installation code by a person familiar with the

construction and operation of the product and the

hazards involved.

Use minimum 90°c supply conductors.

CAUTION: It is important to determine the location of

the electrical box/driver and fixture layout before

beginning the following installation.

MULTIPLE MIRROR INSTALLATION

MULTIPLE MIRROR WITH 600 LMS/F INSTALLATION

1 1

BCATH OLLECTION

ELECTRICAL

BOX

CARDBOARD TEMPLATE

36.5”

24”

1.2

Installation Instructions for

Gia Mirror Kit

700BCGIAMR_

920BCGIADM

Summary of content (8 pages)

PAGE 1
920BCGIADM Installation Instructions for Gia Mirror Kit 700BCGIAMR_ 1.2 B ATH C OLLECTION GENERAL PRODUCT INFORMATION: Suitable for damp locations. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.
PAGE 2
1B 1D FIXTURE FIXTURE BRACKET 3 2 3 2 8 7 SCREW 3 3 5 5 3 3 2 3 2 7 1 Place the fixture on the marked location and mark the location of the holes in the fixture’s mounting bracket. Note: Ensure that the brackets are located behind the mirror 8 2 4 FIXTURE WIRE TUCKED UNDER 3 FIXTURE WIRE TUCKED UNDER 3 5 1C 6 4 3 2 1 ANCHOR 3 5 FIXTURE WIRE TUCKED UNDER 3 5 7 6 6 4 2 At a bracket hole location, push the anchor into the wall up to the threads.
PAGE 3
1E 1G SINGLE DRIVER 3 12 5 3 12 8 5 9 SINGLE DRIVER 12 Note: For 600 lms/f installations, wire each driver separately to the power lines from its dedicated electrical box. 8 Connect the white driver wire to the neutral power line. 9 2 Connect the black driver wire to the hot power line.
PAGE 4
1H MOUNTING PLATE #8-32 SCREW 3 5 14 Properly place the wires and wire nut connections inside the electrical box. 15 If necessary, push any excess fixture wire into the electrical box through the mounting plate. 16 Attach the mounting plate to the electrical box using the two #8-32 screws provided. 17 For 600 lms/f installations, repeat for the other electrical box.
PAGE 5
Install the Mirror 2A 2C MIRROR BRACKET BASE 1 5 5 INNER EDGE SCREW 3 3 5 5 1 1 2B 1 5 5 Align the inner edge of the mirror bracket base to the edge of the mirror markings and mark the location of the holes in the mirror’s mounting bracket base. Note: Ensure that the brackets are leveled and aligned vertically. Replace the mirror bracket bases and secure them by tightening the #8 screw it into the anchors.
PAGE 6
2E 2G 3 3 5 5 MIRROR BRACKET 7 8 MIRROR BRACKET 7 Install mirror brackets only into the lower mirror bracket bases. 8 Tighten the set screws. 10 2F MIRROR 3 5 9 Gently slide the mirror into the assembled lower brackets. 65 Install the top mirror brackets into the bases and tighten the set screws.
PAGE 7
PAGE 8
SAVE THESE INSTRUCTIONS! 7400 Linder Ave, Skokie, IL 60077 847.410.4400 www.techlighting.com © 2014 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right to change specifications for product improvements without notification.