Mini-Z M-Radon V2.1 Instruction Manual

ManualsBrandsTeam Powers ManualsCars & TrucksM-Radon V2.1 Mini-Z 20A Sensored Brushless Speed Control

(Designed & Manufactured by RC EXPLORER TEAM)

M-Radon V2.1 series Brushless Speed Control System User Guidelines

1. Technical /Specifications:

Model:

M- Radon-V2.1

Continuous current:

20A

Burst Current (10sec):

40A

Battery Input: 3.7V LiPo

2 cells

1.2V NiMh/NiCd

6 cells

BEC Output:

Linear 6V/1.5A

Weight (not include wiring & fan):

~4.5g

Dimension(L x W x H) mm

(not include the plug dimension)

~22.5x13.5x9

Miniz Motor limit with 2cell x

3.7V Lipo. The motor timing is at

0 degree

10000KV or below

2. Features:

＊ Ultra-smooth, Precise Throttle and Braking Control

＊ Compatible with Sensored/Sensorless Brushless Motors

＊ Data Analysis Capability(RPM, Low voltage and ESC temperature)

＊ HotWire PC Interface for Advanced Programming and Updating(Not include in the package)

＊ Easily Programming through the LED card (Include in the package)

＊ Built-in one touch On/Off switch with LED

＊ Bulit-in Low voltage cut-off, Overheat protection and signal loss protection

3. Component Included:

- Speed control, Extended BEC wire, Sensor Wire and LED card

Noted: LCD Program card is not included in the package

Summary of content (11 pages)

PAGE 1
(Designed & Manufactured by RC EXPLORER TEAM) M-Radon V2.1 series Brushless Speed Control System User Guidelines 1. Technical /Specifications: Model: M- Radon-V2.1 Continuous current: 20A Burst Current (10sec): 40A Battery Input: 3.7V LiPo 2 cells 1.2V NiMh/NiCd 6 cells BEC Output: Weight (not include wiring & fan): Dimension(L x W x H) mm Linear 6V/1.5A ~4.5g ~22.5x13.5x9 (not include the plug dimension) Miniz Motor limit with 2cell x 10000KV or below 3.7V Lipo.
PAGE 2
4. Connection Diagram: Installation Tips: 1. Connect the speed control BEC wire at the back to the receiver position channel 2. 2. 3. 4. 5. Connect power wire “A” to the motor “A” solder-tabs Connect power wire “B” to the motor “B” solder-tabs Connect power wire “C” to motor “C” solder-tabs Connect the hall sensor cable between the speed control (underneath the solder taps) and motor 6. Connect power wire ”+” to battery “Plus” sign 7. Connect power wire “-“ to battery “Minus” sign Point to notes: 1.
PAGE 3
5.
PAGE 4
Step 2: cont… ◎Move the throttle stick to the full brake position, then the RED Led will be flashing until a solid RED Led will be light up. Light up RED Led represent the full brake position has been set. ◎Move the throttle stick back the neutral position again, then the flashing RED & BLUE(purple color) Led will be light up that means throttle range setting has been completed. ◎The speed control will be ready for use when it powers is off and on again.
PAGE 5
6. Program Card Specifications: ＊ Dimension: 70mm(L) x 45(W) x 13mm(H) ＊ Weight: ~23g Program Card Operation: Step 1: Connection with Speed control: ◎Switch off the speed control power and take out the speed control BEC wire from the receiver. ◎Connect the speed control BEC wire to the LED card connector. Please make sure the speed control wire is connected properly based on the below description. - Connect BEC white color wire to the program card pin at (‘S’) position.
PAGE 6
Step 2: How to program the mode function setting through the setting card: ◎ Press the Item key to select the item setting ◎ Press the Value key to select the item setting values ◎ Press the Update key to update each setting values of each item ◎ Press the Reset key to restore all mode setting to factory default setting ◎ Press and hold the Menu and Value key together for around 2s will enter to Data Analysis mode which can be reviewed RPM, Low voltage and ESC temperature (for LCD card only) 7.
PAGE 7
8. HotWire connection with PC: Below are the two methods to connect the speed control to the PC interface.
PAGE 8
◎ The PC interface software(v3.0) downloaded website: Go http://www.team-powers.com/index.php?thispage=download and download “TP Radon USB link V3.0”. ◎Support Window System: XP SP2, Windows7 and Windows8 How to program the mode function setting through PC interface: ◎ Unzip TP_Radon USB link V3.0.rar and Install TP_Radon USB link V3.0.
PAGE 9
.Troubleshooting Table: Symptom Cause Action to take No motor and servo functions Wiring problem Check wire and connectors Wrong polarity when connecting the Correct the polarity when connecting BEC wire to the receiver the BEC wire to the receiver Transmitter, Receiver or Battery Replace the components one by one defective Speed control defective Send for repair No motor function, but servo is Wiring problem Check wire and connectors working Sensor wiring defective/missing Change other
PAGE 10
.Warning Notes: - - Please read the following instructions carefully before starting to use the unit. For those users that do not have experience to use it, please seek help from the professional users. Please make sure the voltage applied to the unit is in the operating range and the battery + and – sign should be connected properly to the power cord of the unit. If battery +, - is reversed to connect to the unit, the unit will be burnt out.
PAGE 11
can be granted. For quick repair-and return service, please add your address and detailed description of the malfunction. If Team Powers are unable to service those defective products that are no longer exist in the market, we shall provide you with a product that has at least the same value from one of the successor series. The specifications like weight, size and others should be seen as in this user guideline.