Datasheet

ManualsBrandsTE Connectivity ManualsAutomotive RelaysAutomotive PCB Relay V23086, 1CO, DC, 12V, 30A, 254Ohm

02-2015, Rev. 0215

www.te.com

a TE Connectivity Ltd. company.

Datasheets and product speciﬁcation ac-

cording to IEC 61810-1 and to be used only

together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations

are subject to change.

Small power relay

Limiting continuous current 30A

Low weight

Low noise operation

Wave (THT) and reﬂow (THR/pin-in-paste) solderable versions

Typical applications

Car alarm, door control, door lock, heated front/rear screen, immobilizer,

lamps front/rear/fog light, interior lights, seat control, sun roof, window

lifter, wiper control.

Micro Relay K (THT – THR)

Automotive Relays

PCB Single Relays

Contact Data

Typical applications Inductive load Wiper load Resistive/inductive load Lamp load

V23086-*1*01-A403 V23086-*1*02-A803 V23086-*1*01-A402 V23086-*1*51-A502

Contact arrangement 1 form C, 1 CO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO

Rated voltage 12VDC 10VDC 12VDC 12VDC

NO/NC NO/NC

Rated current 30/25A 30/25A 30A 30A

Limiting continuous current

23°C 30/25A 30/25A 30A 30A

85°C 20/15A 20/15A 20A 20A

Limiting making current 40A

40A

100A

Limiting breaking current 30A 30A 30A 30A

Contact material AgSnO

Min. recommended contact load 1A at 5VDC

Initial voltage drop at 10A, typ./max. 30/300mV

Operate/release time typ. 3/1.5ms

Electrical enduranc

cyclic temperature -40°C, +25°C, +85°C

form C contact (CO) at 14VDC motor reverse blocked, wiper,

25A, 0.77mH 25A make/5A break,

>1x10

ops. generator peak,

20A on NC,1mH

>1x10

ops.

form A contact (NO) at 14VDC resistive 20A lamp 100A inrush,

>3x10

ops. 10A steady state

>1x10

ops.

Mechanical endurance >5x10

ops.

Max. DC load breaking capacity

Load limit curve 1: arc extinguishes, during transit time (changeover contact).

Load limit curve 2: safe shutdown, no stationary arc (make contact).

Load limit curves measured with low inductive resistors veriﬁed for 1000 switching events.

1) The values apply to a resistive or inductive load with suitable spark suppression and at

maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum

3s for a make/break ratio of 1:10.

2) Corresponds to the peak inrush current on initial actuation (cold ﬁlament).

3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at

http://relays.te.com/appnotes/

4) Measured at nominal voltage without coil suppression unit. A low resistive suppression

device in parallel to the relay coil increases the release time and reducesthe lifetime

caused by increased erosion and/or higher risk of contact tack welding.

5) Be aware of using right polarity, see Terminal Assignment. Wrong polarity will reduce

endurance.

086C/R1_fcw1b

Summary of content (5 pages)

PAGE 1
Automotive Relays PCB Single Relays Micro Relay K (THT – THR) n n n n n Small power relay Limiting continuous current 30A Low weight Low noise operation Wave (THT) and reflow (THR/pin-in-paste) solderable versions Typical applications Car alarm, door control, door lock, heated front/rear screen, immobilizer, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control.
PAGE 2
Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Coil Data Rated coil voltage Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001/801 12 6.9 002/802 10 5.7 051/851 10 6.5 Other Data 12VDC Release voltage VDC 1.5 1.25 1.1 Coil resistance Ω±10% 254 181 90 Rated coil power mW 0567 0552 1111 All figures are given for coil without pre-energization, at ambient temperature +23°C.
PAGE 3
Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Terminal Assignment Bottom view on solder pins 1 form A, 1 NO 4 5 1 form A, 1 NO (lamp load) 1 form C, 1 CO 4 3 1 5 2 (+) 1 1 5 2 2 86etw_ab 86ets_ab (–) 4 Dimensions Micro Relay K, THT version 86ets_ab Mounting Hole Layout Bottom view on solder pins 12.0 ± 0.2 ± 0.2 0.6 ± 0.2 8.5 C 7.5 +0 .0 5 2.5 ± 0.1 3x 5.8 1. 2 0 0.5 B 0.5 10.2 1 3.6 4 3.0 ± 0.2 +0.05 0 3 5 9.9 0.4 7.65 ± 0.1 ± 0.
PAGE 4
Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Mounting Hole Layout Bottom view on solder pins *) Micro Relay K, THR version 86R1_DD2_2 86R1_VT3 View of Stand-Offs Bottom view on solder pins 86R1_DD1_2 86R1_VT1 *) Additional tin tops max. 1mm 4 02-2015, Rev. 0215 www.te.com © 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
PAGE 5
Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Product code structure Typical product code V23086 -C 1 001 -A 4 03 Type V23086 Micro Relay K (THT – THR) Terminal and enclosure C PCB version THT, sealed Design 1 Single relay Coil 001 Standard (THT) 801 Standard (THR) 051 Lamp load (THT) Contact type A Single contact Contact material index 4 AgSnO2 standard 5 AgSnO2 lamp load Contact arrangement index 02 NO Product code V23086-C1001-A402 V23086-C1001-A403 V23086-C1051-A5