Datasheet

ManualsBrandsTE Connectivity ManualsAutomotive RelaysAutomotive Relay V23076, 1CO, DC, 24V, 45A, 362Ohm

11-2013, Rev. 1113

www.te.com

a TE Connectivity Ltd. company.

Catalog and product speciﬁcation according

to IEC 61810-1 and to be used only together

with the ‘Deﬁnitions’ section.

Catalog and product data is subject to the

terms of the disclaimer and all chapters of

the ‘Deﬁnitions’ section, available at

http://relays.te.com/definitions

Catalog product data, ‘Deﬁnitions’ section,

application notes and all speciﬁcations are

subject to change.

Power Relay K (Open – Sealed)

Automotive Relays

PCB Single Relays

Limiting continuous current 45A

Wide voltage range

24VDC coil versions available

For high current version refer to Power Relay K-S

Typical applications

ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,

hazard warning signal, heated front screen, heated rear screen, ignition,

lamps front/rear/fog light, interior lights, main switch/supply relay, seat

control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,

wiper control.

Contact Data

Typical applications Resistive/inductive Resistive/inductive Indicator lamps Headlights, Headlights

loads loads capacitive loads capacitive loads

Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO 1 form C, 1 CO

Rated voltage 12VDC 12VDC 12VDC 12VDC 12VDC

A/B (NO/NC) A/B (NO/NC)

Rated current 45A 45/30A 30A 40A 40/25A

Limiting continuous current

23°C 45A 45/30A 30A 40A 40/25A

85°C 30A 30/25A 25A 25A 25/20A

Limiting making current

100A 100/30A 120A

180A 180/60A

Limiting breaking current

60A 60/30A 60A 60A 60/30A

Contact material AgNi0.15 AgNi0.15 AgSnO

AgSnO

Min. recommended contact load 1A at 5VDC

Initial voltage drop, at 10A, typ./max. 20/300mV

Operate/release time typ. 5/3ms

Electrical endurance >2x10

ops. >2x10

ops. >2.2x10

ops. >10

ops.

at 13.5VDC, 40A at 13.5VDC, 40A up to 8x21W up to 4x60W up to 4x60W

Mechanical endurance, DC coil >10

ops.

1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.

2) For a load current duration of maximum 3s for a make/break ratio of 1:10.

3) Corresponds to a peak inrush current on initial actuation (cold ﬁlament).

4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/

5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher

risk of contact tack welding.

TE0556-E

Max. DC load breaking capacity

Load limit curve 1: arc extinguishes, during transit time (changeover contact).

Load limit curve 2: safe shutdown, no stationary arc (make contact).

Load limit curves measured with low inductive resistors veriﬁed for 1000 switching events.

Summary of content (4 pages)

PAGE 1
Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) n n n n Limiting continuous current 45A Wide voltage range 24VDC coil versions available For high current version refer to Power Relay K-S Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, va
PAGE 2
Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) (Continued) Coil Data Rated coil voltage Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001 12 6.9 022 24 14.1 Insulation Data 12VDC / 24VDC Release voltage VDC 1.2 2.4 Coil resistance Ω±10% 90 362 Rated coil power W 1.6 1.6 All figures are given for coil without pre-energization, at ambient temperature +23°C. Other coils on request.
PAGE 3
Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) (Continued) Dimensions Power Relay K open version Power Relay K sealed version 26.1 ±0.4 18.6 ±0.65 23.3 ±0.7 8.5 ±0.2 21.1 ±0.4 18.0 ±0.5 9.2 ±0.4 18.9 ±0.3 2.4 ±0.8 3.0 ±0.5 *) *) additional tin tops max. 1.5 mm Assembly and positioning aid 2.5 ±0.4 3.4 ±0.1 2.5 – 3.0 Terminals tinned TE2179-42 3.4 ±0.1 21.2 ±0.3 3.0 ±0.5 *) 2.5 – 3.0 0.55 ±0.25 TE0579-I2 Terminals tinned *) additional tin tops max. 1.
PAGE 4
Automotive Relays PCB Single Relays Power Relay K (Open – Sealed) (Continued) Product code structure Typical product code V23076 -A 1 022 -C 13 3 Type V23076 Power Relay K, sealed V23133 Power Relay K, open Terminal A PCB Design 1 Single relay Coil 001 12VDC Contact type C Single contact Contact material 13 AgNi0.15 15 AgSnO2 (Special) Contact arrangement 2 1 form A, 1 NO Product code Terminal/Encl.