Information

ManualsBrandsTE CONNECTIVITY ManualsIndustrial Connectors (Misc.)Nominal current: See data sheet Content: 1 p

108

10037

Product

Specification

11 Mar 11 Rev

Type XII Contact

a TE Connectivity Ltd. Company

| Indicates Change

*Trademark

For latest revision, visit out website at www.te.com/documents

For Regional Customer service, visit our website at www.te.com

1 of 6

TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

1. SCOPE

1.1. Content

This specification covers the performance, tests and quality requirements for Type XII contacts

assembled in the G series connector housing. These contacts are primarily intended for use where the

coupling means is provided separately from the individual contacts.

1.2. Qualification

When tests are performed on the subject product line, the procedures specified in 109-Series Test

Specifications shall be used. All inspections shall be performed using the applicable inspection plan

and product drawing.

2. APPLICABLE DOCUMENTS

The following documents form a part of this specification to the extent specified herein. In the event of

conflict between the requirements of this specification and the product drawing, the product drawing

shall take precedence. In the event of conflict between the requirements of this specification and the

referenced documents, this specification shall take precedence.

2.1. TE Connectivity (TE) Documents

A. 109-1: General Requirements for Test Specifications

B. 109 Series: Test Specifications as indicated in Figure 1.

C. 114-10005: Contact, Type XII, Application Of

D. 501-143: Test Report

2.2. Military Standard

MIL-W-16878: Wire, Electrical, Insulated, High Temperature

3. REQUIREMENTS

3.1. Design and Construction

Product shall be of the design, construction and physical dimensions specified on the applicable

product drawing.

3.2. Material

Contact: Copper, tin-lead, gold over nickel or silver over nickel plating

3.3. Ratings

Temperature:

1. -55° to 105°C for tin-lead

2. -55° to 125°C for gold over nickel or silver ove r nickel

3.4. Performance and Test Description

The product is designed to meet the electrical, mechanical and environmental performance

requirements specified in Figure 1. All tests are performed at ambient environmental conditions per

Test Specification 109-1 unless otherwise specified.

Summary of content (6 pages)

PAGE 1
08-10037 Product Specification 11 Mar 11 Rev A Type XII Contact 1. SCOPE 1.1. Content This specification covers the performance, tests and quality requirements for Type XII contacts assembled in the G series connector housing. These contacts are primarily intended for use where the coupling means is provided separately from the individual contacts. 1.2. Qualification When tests are performed on the subject product line, the procedures specified in 109-Series Test Specifications shall be used.
PAGE 2
108-10037 3.5. Test Requirements and Procedures Summary Test Description Examination of Product Termination Resistance, Specified Current Termination Resistance, Dry Circuit Current Cycling Vibration Requirement Meets requirements of product drawing and applicable TE application specification. ELECTRICAL 1.0 milliohm maximum final AWG Amperes 10 25 12 18 14 15 16 13 .5 milliohm maximum initial. .6 milliohm maximum final, gold and silver .4.0 milliohms maximum final, tinlead. See note (a).
PAGE 3
108-10037 Test Description Crimp Tensile Durability Requirement Wire Size AWG 10 12 14 16 See note (a). Humidity-Temperature Cycling ENVIRONMENTAL See Note. Mixed Flowing Gas See Note. Subject mated contacts assembled in housings to class III for 20 days; Test Specification 109-85-3. Temperature Life See Note. Subject mated contacts assembled in housings to a maximum rated temperature for 240 hours; Test Specification 109-43.
PAGE 4
108-10037 3.6.
PAGE 5
108-10037 4.4. Quality Conformance Inspection The applicable quality inspection plan will specify the sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with the applicable product drawing and this specification. Figure 3 Termination Resistance Measurement Points NOTE Cable tie down. 8 inches from rear of connector.
PAGE 6
108-10037 Gage 1 .110 2 .100 A + .0000 - .0001 + .0000 - .0001 B .250 ± .020 .250 ± .