Bluetooth Module Datasheet 蓝牙模组规格说明书 版本 Version:V1.0 公布日期 Release Date: 2017-06-28 TONLY ELECTRONICS HOLDINGS LIMITED.通力电子控股有限公司 Address:Section 37, Zhongkai Hi-tech Development Zone, Huizhou Guangdong 516006, P.R.China 地址:中国广东省惠州市仲恺高新区惠风 6 路 37 号小区 网址 http://www.tonlyele.com ©2015 TONLY ELECTRONICS HOLDINGS LIMITED.
XXXX Module Datasheet 法律声明 Legal Notice,Disclaimer,Copyright 本手册是通力电子控股有限公司机密,未经能力电子控股有限公司的事先书面许可,任何人不得复制、 传播本手册的内容。通力电子控股有限公司不对由使用本手册或执行本手册内容带来的损害负责。 本手册所涉及的知识产权归通力电子控股有限公司所有(或经合作商授权许可使用) ,任何人不得侵 犯。 本手册是按当前状态提供参考,本公司司保留随时更新本手册的权利,恕不另行通知。 本手册不对包括但不限于下列事项担保:适销性、特殊用途的适应性;实施该用途不会侵犯第三方的知 识产权等权利。 本文档在此未以禁止反言或其它方式授予任何知识产权使用许可,不管是明示许可还是暗 示许可。 本手册中提到的所有商标名称、商标和注册商标均属其各自所有者的财产,特此声明. 本协议以中、英文两种语言制作,两种语言文本冲突时,任何时候均以英文为准。 This data sheet contains information that is confidential to TONLY ELECTRONICS HOLDINGS LIMITED.
XXXX Module Datasheet 版本变更说明 Document Revision History Revision Date Author Description 版本 日期 作者 描述 V1.0 2017-06-28 3 孙强耀 First release.
XXXX Module Datasheet 目录 Table of Contents 法律声明 Legal Notice,Disclaimer,Copyright 文档变更说明 Document Revision History 目录 Table of contents 1.系统概览 System overview 1.1 通用说明 General Descriptions 1.2 性能特点 Features 1.3 系统方框图 Block Diagram 2.产品描述 Production Description 引脚与功能说明 Pin Layout & Pin Description 外观与尺寸 Appearance& Dimension 3.应用说明 ApplicationExplanation 4.电气特性 ElectricalCharacteristics 工作条件 直流特性 DC characteristics 电流消耗 Current consumption 5.
XXXX Module Datasheet 1.系统概览 System overview EXM1020 Bluetooth Low Energy Module provides a highly integrated solution for delivering low power Bluetooth v4.2 solutions. The advanced command interface offers rapid time to market . EXM1020 module complies with Bluetooth specification version v4.2. It integrates RF, a baseband controller, making it a complete Bluetooth Low Energy Solution. EXM1020can be used with either low cost microcontroller for intelligent Bluetooth Low Energy applications.
XXXX Module Datasheet 2.产品说明 Production Description Fully qualified Bluetooth version 4.2 low Energy Module Command interface API over SPI Castellated SMT pads for easy and reliable PCB Mounting Environmentally friendly, RoHS compliant Device Firmware Upgrade (DFU) over SPI or Over the Air (OTA) Remote commands over the air Antenna ready Figure as below.
XXXX Module Datasheet Pin feature descriptions PIN Symbol Description Function 1 VSS[4] GND. GND 2 VSS[5] GND. GND 3 I2S_WS 4 I2S_CLK Continuous serial clock PIO[12] 5 I2S_SDA Serial data PIO[11] 6 PIO10 Programmable I/O. PIO[10] 7 VDD_Flash Power supply for Flash Type 3.3V 8 PIO9 Programmable I/O.
XXXX Module Datasheet 18 SPI_PIO# CLK selected by SPI_PIO#. •PIO[0] SPI/PIOactive-high. Input with internal pull down; selects SPI Active-high. 19 PIO[14] Programmable I/O. 22 VDD_MEM VBAT for internal flash 23 VDD_BAT Power supply for moudle 24 AIO[0] Bi-directional with PIO[14] programmable Analogue Programmable I/O analog I/O. 3.应用说明 Application Explanations Smart Audio Smart light IOT 4. 电气特性 Electrical Characteristics ELECTRICAL CHARACTERISTICS Supply Voltage 0.
XXXX Module Datasheet 5.射频性能 RF Performance Specification Description RF performance Standard Bluetooth 4.2 Frequency Band 2.4 ~ 2.4835 GHz Modulation Method GFSK Maximum Data Rate 1 Mbps Antenna PCB Antenna Interface UART, PIO, AIO, SPI,PCM, Operation Range 30 meters Sensitivity -85 dBm at 0.1% BER RF TX Power +0 dBm (avg), +4 dBm(peak) 6.认证与法规信息 Certification& Regulation The BQB Certification:still on-going.
XXXX Module Datasheet 7.环保声明 Green Policy This module can meet ROHS&REACH compliance.XXXX 8.
For IC: This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d'Industrie. This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) For all products market in United States, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool.