TCL多 媒体 SCB C(战略客户业务中心) 设计中心-平面设计室 机型/机芯 物料编码 物料名称 品牌 说明书 制作要求 尺寸 143X210MM 材质 80g书纸 销往地 Pixel 1NT671A2ATA 销售型号 资料更新履历 平面设计制作规范表 基本内容 USA/美国 BOM /批次 工艺或使用方法 资料由客户业务确认提供,如有误请以客户业务审签资料为准。 颜色 要求 黑白印刷 底座安装示意为通用示意 是否折 叠或装 订要求 是否送样 备注: 制作人 袁惠芳 制作日期 2020-8 平面审核 硬件会签 结构会签 业务/DQA 会 签 软件会签
Operation manual
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
1
The mains plug/appliance couple is used as disconnect device,the disconnect device shall remain readily operable.
Chapter 1: Introduction Precautions ................................................................................................................................................. Product ........................................................................................................................................................ Power and Plug ...........................................................................................................................................
Introduction Chapter 1 Precautions Use Environment Read all of the instructions before operating the set. Keep these instructions well for future use. Do not place the set on an unstable cart, stand, or table. Product Place the set on a place that allows good ventilation. Do not block or cover the ventilation openings on the back cover. Do not use the set near damp, and cold areas. Protect the set from overheating.
Introduction Reference section 58" Wall mount hole pattern VESA (mm):400*300mm Wall mount screw size (mm):M6*12mm,4pcs 70" Wall mount hole pattern VESA (mm):400*300mm Wall mount screw size (mm):M6*15mm,4pcs Note:Some specifications may vary by different regions or models, and please take your actual TV set as the standard.
Introduction Sockets Note: The location and names of the sockets on the TV may vary according to TV model, and some sockets may not available for some models. USB LAN USB sockets These sockets can be used to connect an USB device. Note: The number of USB sockets on the TV may vary according to TV model. LAN RJ45 plug for connecting to external modem or network access equipment. ANTENNA IN ANTENNA IN socket This socket can be used to connect the outside aerial or cable network.
Introduction Remote Control Functions Most of your television's functions are available via the menus that appear on the screen. The remote control supplied with your set can be used to navigate through the menus and to configure all the general settings. (On/Off button) Turns the TV on or off. POWER To mute and un-mute the sound. Goes to the smart TV homepage. Enter into Quick Access Menu.
Chapter 2 Connections and Setup Switching on Follow the instructions on this page on how to switch on your TV set and the remote control before going on to following pages describing how to use the channel set-up procedure. 1. Insert two batteries in the remote control. Precautions on using batteries: - Only use the battery types specified. - Make sure you use the correct polarity. - Do not mix new and used batteries. - Do not use rechargeable batteries.
Connections and Setup Network Connection To access the Internet, you must subscribe to high speed broadband Internet service with your Internet service provider (ISP). Your TV can be connected to your home network in two ways: • Wired, using the RJ45 (LAN) connector on the back panel. • Wireless, using the internal wireless and your home wireless network. Note: Instructions below are just the usual ways to connect your TV to the wired or wireless network.
Chapter 3 Menu Function You can press the menu button enter to choose the Settings Menu. Please note the menus in the user manual may vary slightly from the actual screen. In each menu, you can: • Press the up, down, left and right buttons to select an item or to adjust the value. • Press the OK button to enter the submenu. • Press the BACK button to return to previous menu or exit the menu. Network Internet Connection Selects On to adjust the options below.
Connectivity T-Link T-Link Remote Control USB Keyboard Setting Child Code Lock System Enter to select On or Off. Change Code Enter to change code. Clear Code Enter to clear code. Help Go in and learn about certain functional operations. About TV Product Information Update Software - Network Updates Enables you to download and install the latest software version from the Internet. Make sure to set up a wired or wireless network connection first.
Chapter 4 Attention and Frequently Asked Questions Attention: Some non-standard mobile storage device may not be recognized. Please change to use the standard device. Note: For coding files, there are many kinds nonstandard coding method, so this system can not be guaranteed to support the file formats using any coding method. Frequently Asked Questions: 1.
Chapter 5 Troubleshooting Ignition Black spots or horizontal streaks appear, or the picture flutters or drifts. This is usually caused by interference from car ignition system, neon lamps, electric drills, or other electrical appliance. Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list. No picture, no sound 1. Check if the fuse or circuit breaker is working. 2. Plug another electrical device into the outlet to make sure it is working or turned on. 3.