D01083020A M-164 M-164FX M-164UF Analog Mixer OWNER'S MANUAL
IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. •• Do not expose this apparatus to drips or splashes. 2 Keep these instructions. •• Do not place any objects filled with liquids, such as vases, on the apparatus. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. •• Do not install this apparatus in a confined space such as a book case or similar unit.
Contents 1 − Introduction.......................................... 5 Main features................................................... 5 Included items.................................................. 5 About this manual........................................... 5 Trademarks....................................................... 6 Precautions and notes for placement and use..................................................................... 6 Cleaning the unit.............................................
1 − Introduction Thank you very much for purchasing this TASCAM M-164 series mixer. •• AUX MASTER (1, 2) knobs adjust the total AUX 1 and 2 Before using the unit, please read this Owner’s Manual carefully so that you will understand the correct operating procedures. We hope that you will enjoy using this product for many years to come. •• Bus assign switches on all input channels Please keep this manual for future reference.
1 − Introduction Explanation of actions in special situation and supplement. CAUTION Instructions that should be followed to avoid injury, damage to the unit or other equipment, and loss of data. Trademarks •• TASCAM is a registered trademark of TEAC Corporation. •• Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. •• Macintosh, Mac OS and Mac OS X are trademarks of Apple Inc.
2 − Names and Functions of Parts Top panel ** * * * M-164FX, M-164UF only ** M-164UF only 1**USB indicator Lights when the mixer is connected to a computer by USB. 2 Input channel meters Display the input level of each input channel (levels after signals pass through the EQ section). 3 MONITOR (L, R) meters Display the output signal level of the monitoring source (stereo, SUB or AUX 1 bus) that has been selected with the two switches at the MONITOR section.
2 − Names and Functions of Parts 8 HPF switch (channels 1–6) Push this switch in to turn ON the high-pass filter, which cuts frequencies below 80 Hz by 12 dB/octave. The high-pass filters affect inputs from both MIC and LINE input jacks. 9 EQ knobs (channels 1–6) These channels each have a 3-band EQ. The EQ HI knob adjusts the high frequency range with a roll-off frequency of 12 kHz and a boost/cut range of ±15 dB. The EQ MID knob adjusts the middle frequency range with a central frequency of 2.
2 − Names and Functions of Parts k TO ST switch Turn this switch ON (push switch in) to send the SUB bus output signal to the stereo bus. l TO AUX 1 switch(es) The M-164 has one switch for channels 13-14. The M-164FX has one switch each for both channel 13-14 and 15-16 pairs. The M-164UF has one switch each for channel 11-12, 13-14 and 15-16 pairs. When ON (switch pushed in), the post-fader signal (signal after being adjusted by the fader) is sent to the AUX 1 bus.
2 − Names and Functions of Parts Rear panel * *M-164UF only x AUX SEND 1 and 2 jacks (standard jacks) These are balanced outputs for the AUX bus 1 and 2 signals. Unbalanced connections are also possible. Use with external effects or monitoring systems. c LINE input jacks (standard jacks) The outputs of electronic instruments, audio equipment and other line level signals can be connected to these input jacks. Both 3-pole balanced and 2-pole unbalanced standard plugs can be connected.
2 − Names and Functions of Parts $* USB port (M-164UF ONLY) Connect the mixer to a computer from this port using the included USB cable. % 7-8 input jacks (standard jacks) The outputs of electronic instruments, audio equipment and other line level signals can be connected to these input jacks. Both 3-pole balanced and 2-pole unbalanced standard plugs can be connected. If a connection is only made to the L/MONO input jack, the signal is sent to both left and right channels.
3 − Preparation for Use This chapter explains how to connect external equipment and the power cord, as well as how to make other preparations before turning on the power. See “5–Using with a Computer (M-164UF)” for an explanation of how to connect an M-164UF mixer with a computer. Connecting the power Confirm that the mixer power switch is set to STANDBY beforehand. Connect the included power cord and AC adaptor (TASCAM PS-1225L) to the mixer.
3 − Preparation for Use Connection example 1: Using an M-164 with multiple mics and for background music in a club External effect unit Connect mics to MIC (1-6) Stereo amplifier Record player CD player Headphones iPod TASCAM M-164/M-164FX/M-164UF 13
3 − Preparation for Use Connection example 2: Using an M-164UF for recording in a home studio Electronic keyboard External effect unit Connect mics to MIC (1-6) 7-8 (L, R) Stereo amplifier Computer USB Stereo amplifier Rhythm machine Stereo amplifier CD player Headphones 14 TASCAM M-164/M-164FX/M-164UF
3 − Preparation for Use Making stereo output connections Connecting headphones To monitor with headphones, connect stereo headphones to the PHONES jack on the top panel. CAUTION Turn the power OFF on all equipment to be connected and set the mixer to standby before making connections. The mixer stereo bus output is usually used as the main output and connected to an external amplifier or speaker system.
3 − Preparation for Use CAUTION •• Connecting a dynamic mic with an unbalanced connection could damage it if the PHANTOM (+48V) switch is ON. •• Do not connect or disconnect mics when the PHANTOM (+48V) switch is ON. Doing so could cause loud noise or damage the equipment. •• When the PHANTOM (+48V) switch is ON (and the mixer power is ON) the +48V indicator lights on the right side of the meter panel. •• The XLR connector #2 pins are “hot” on this mixer.
3 − Preparation for Use 15-16 STEREO IN jack on the top panel, select channels 13-14 as the return channels by setting the INT. EFFECT RTN switch so that it is not pushed in. Indicator STEREO IN jack When using channels 13-14 as the return channels, do not use the channel 13-14 input jacks on the rear panel. When using channels 15-16 as the return channels, do not use the STEREO IN jack on the top panel.
4 − Using the mixer Adjusting levels 3 Raise the ST (stereo) fader to the 0 position. After turning on the power, adjust the level of each input signal. The following explanation assumes that the STEREO OUTPUTS are being used as the main outputs. 1 Prepare headphones or an amplification system to output the sound in advance. If monitoring with headphones, raise the volume with the PHONES LEVEL knob slightly. If monitoring with an amplification system, raise the input level on the amp slightly.
4 − Using the mixer 5 Raise the channel fader. Using the mixer channel functions High-pass filter (HPF) Press the HPF switch to turn the high-pass filter ON and cut frequencies of 80 Hz or less by –12 dB/octave. The high-pass filter affects inputs from both MIC and LINE input jacks, but it is especially effective when using mics for reducing unwanted noise from wind and breathing.
4 − Using the mixer Channels 7-8 and 9-10 have 2-band EQ with HI and LOW shelving frequency boost and cut adjustment ranges of ±15 dB. Use the EQ HI knob to boost or cut the frequency band above 12 kHz, and use the EQ LOW knob to boost or cut the frequency band below 100 Hz.
4 − Using the mixer Pan And Balance Monitoring with headphones You can monitor the outputs of the mixer’s stereo, SUB or AUX 1 send bus. For channels 1–6, use the PAN knob to set the left-right stereo position of the channel signal sent to the stereo and SUB busses. For stereo channels 7-8 and 9-10, use the BAL knob to set the left-right balance of the stereo channel signals sent to the stereo and SUB busses. 1 Connect stereo headphones to the PHONES jack on the top panel of the mixer.
4 − Using the mixer M-164 Series mixer AUX SEND 1 jack AMP Stage monitor 3 Use the AUX MASTER 1 knob to adjust the overall level sent to the AUX 1 send bus. PHONES jack 1 Turn ON (push in) the PRE switch under the AUX 1 knob of each channel that you want to monitor. Using sub-group functions By using the SUB bus as a sub-group, you can make adjusting the stereo mix balance more efficient. 2 Use each channel’s AUX 1 knob to adjust the signal level sent for monitoring.
4 − Using the mixer Using the internal effects (M-164FX and M-164UF) M-164FX and M-164UF units have an internal effects capability that allows the use of an effect without connecting an external effect unit. These internal effects can be applied by sending signals from channels 1–6, 7-8 and 9-10 to the AUX 2 bus. The return signal can be sent to channels 13-14 or 15-16.
4 − Using the mixer 4 Select the input channel for the return signal. Push the INT. EFFECT RTN switch in to send the return signal to channels 15-16. Leave the switch out (do not press it in) to send the return signal to channels 13-14. •• When sending signals to an external effect through AUX 1, turn the PRE switch OFF to send the post fader signal. •• When receiving external effect signals back through channels 13-14, do not set the internal effect return to channels 13-14 (by setting the INT.
4 − Using the mixer Using a record player An analog record player can be directly connected to mixer channels 9-10. Make the following connections and settings to use an analog record player with this mixer. Making final adjustments to the main output sound The stereo bus has a 2-band EQ with HI and LOW shelving that can be used to adjust the sound of the mix overall. •• Connect the record player audio output to the channel 9-10 input jacks on the rear panel of the mixer.
5 − Using with a Computer (M-164UF) When connected with a computer by USB, the M-164UF mixer can function as a USB 2.0 interface. Using the included Cubase LE4 or another audio application, you can easily create music on your computer. In addition, you can input a sound that you have created or edited on the computer into the M-164UF mixer, and mix it with live playing in a performance application. These requirements must be satisfied if you plan to use Cubase LE 4 (bundled with the M-164UF).
5 − Using with a Computer (M-164UF) When installing the driver, start with the M-164UF mixer disconnected. CAUTION •• Handle the enclosed CD-ROM with care. If the disc becomes scratched or dirty, your computer may be unable to read it and you may be unable to install the software. If the disc becomes unreadable, you can request a replacement disc for a fee. •• Do not try to play the included CD-ROM disc on an ordinary audio CD player. The noise produced could damage the speakers or harm your hearing.
5 − Using with a Computer (M-164UF) 6 Read the contents of the License Agreement, then select I accept the agreement if you agree to the terms. Click the Install button to start installation. 10 When the following screen appears, installation has completed. 7 When the following screen appears, use the included USB cable to connect the mixer (M-164UF) with the computer. 8 When the following screen appears, disconnect the USB cable from the mixer (M-164UF) or the computer for a moment.
5 − Using with a Computer (M-164UF) How to update the firmware By connecting the M-164UF with a computer by USB, you can overwrite the mixer firmware. The latest firmware updater can be downloaded from our http://www.tascam.com website. Preparation 1: Install the latest driver on your computer. Preparation 2: Connect the M-164UF to be updated to the computer by USB. 5 Click the Exit button to complete updating. The firmware updater differs according to the version.
5 − Using with a Computer (M-164UF) Control panel settings Connecting by USB Overview Use the included USB cable to connect the M-164UF with a computer as shown in the illustration. M-164UF functions can be set from the control panel. On Windows XP, the M-164UF Control Panel can be accessed from shortcuts in the following locations. •• Start menu •• Control panels Computer •• Programs/TASCAM/M-164UF On Mac OS X, the M-164UF Control Panel is located inside the application folder.
6 − Troubleshooting Related to mixer settings Q: There is a humming noise coming from external equipment. Q: There is no sound from the speakers connected to the STEREO OUTPUTS jacks. A: A: Turn the MONITOR ST switch ON and check the MONITOR meters. If the meter indicators are changing: •• Check the settings and volume of the connected amplification system.
7 − Specifications and Block Diagrams Ratings Internal operation level: –2 dBu 15-16 input jacks Connectors: 3-pole mini-jack (tip: L, ring: R, sleeve: ground) Circuit type: unbalanced Inputs Input impedance: 10 kΩ MIC input jacks (channels 1–6) Connectors: XLR-3-31 Circuit type: electronically balanced (#1: ground, #2: hot, #3: cold) Input impedance: 2.
7 − Specifications and Block Diagrams AUX SEND (1, 2) jacks Connectors: 3-pole standard jacks Circuit type: Pseudo balanced (tip: hot, ring: cold, sleeve: ground) •• Illustrations in this Owner’s Manual might differ from the appearance of the actual product. •• In order to improve a product, its specifications and/ or appearance might be changed without notice.
7 − Specifications and Block Diagrams Dimensional drawing 34 TASCAM M-164/M-164FX/M-164UF 344.5 mm 112 mm 349.
7 − Specifications and Block Diagrams R L R P R L/MONO R L R L R L/MONO P LINE MIC M-164 Block Diagram P P P P L P R L Block diagram TASCAM M-164/M-164FX/M-164UF 35
7 − Specifications and Block Diagrams Level diagram 36 TASCAM M-164/M-164FX/M-164UF
Notes TASCAM M-164/M-164FX/M-164UF 37
Notes 38 TASCAM M-164/M-164FX/M-164UF
Notes TASCAM M-164/M-164FX/M-164UF 39
M-164 TEAC CORPORATION Phone: +81-42-356-9143 1-47 Ochiai, Tama-shi, Tokyo 206-8530, Japan TEAC AMERICA, INC. www.tascam.jp www.tascam.com Phone: +1-323-726-0303 7733 Telegraph Road, Montebello, California 90640 USA TEAC CANADA LTD. www.tascam.com Phone: +1905-890-8008 Facsimile: +1905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.A. de C.V. www.teacmexico.
