User Guide
Targus Bluetooth Comfort Laser Mouse Introduction Thank you for your purchase of the Targus Bluetooth Comfort Laser Mouse. This mouse uses Bluetooth technology which provides a seamless connection up to 33 ft (10 m) away. This is a plug and play device so no additional software is required. The advance scroll wheel feature program can be downloaded from the Targus web-site.
Targus Bluetooth Comfort Laser Mouse Installing the Batteries 1. Remove the battery cover from the top of the mouse by using the notch on the back. Carefully lift the cover up as shown in the diagram. 2. Remove the battery safety clip by squeezing the center of the clip and sliding it back, towards the rear of the mouse. Lift up and rotate the clip out of the way. NOTE: THE BATTERY SAFETY CLIP WILL NEED TO BE IN THE SECURE, LOCKED POSITION BEFORE THE BATTERY COVER CAN BE PUT BACK IN PLACE.
Targus Bluetooth Comfort Laser Mouse 3. Slide and lift to remove the battery holder as shown. 4. Insert the two AA batteries, making sure that the positive (+) and negative (-) ends of each battery match the polarity indicators inside the battery compartment.
Targus Bluetooth Comfort Laser Mouse 5. Replace the battery safety clip and by sliding it forward until it clicks into place and then replace the battery cover. 6. Turn on the mouse by pressing the power on/off button on the bottom of the mouse. Hold for 3 seconds and then release.
Targus Bluetooth Comfort Laser Mouse Power On: Press and hold the power button for 3 seconds and then release. The battery life indicator will briefly light up showing the current power level of the batteries. Power Off: Press and hold the power button for 3 seconds and then release. The battery life indicator will briefly light up and then fade out. Battery Check: After the mouse is turned on, quickly press and release the power button.
Targus Bluetooth Comfort Laser Mouse Power Saving mode: !FTER AN EXTENDED PERIOD OF TIME IF THE MOUSE IS NOT USED IT WILL AUTOMATICALLY ENTER power saving mode to conserve power and increase battery life. Click on any mouse button to resume the normal operation. The mouse may take a few seconds to reconnect with your computer.
Targus Bluetooth Comfort Laser Mouse Initial Configuration Before you can begin using your Bluetooth® mouse, you will first need to perform some initial setup steps. NOTE: PLEASE USE THE LATEST BLUETOOTH DEVICE DRIVER. INSTRUCTION SCREENS MIGHT VARY DEPENDING ON THE VERSION OF YOUR BLUETOOTH DEVICE DRIVER.
Targus Bluetooth Comfort Laser Mouse Connecting with Bluetooth Software: 7)$#/-- OR -ICROSOFT 7INDOWS 80 7INDOWS 6ISTA 1. Go to the Bluetooth Places icon located on your desktop or in the system tray and double click, then click Add a Bluetooth Device. (Windows XP) 7INDOWS 6ISTA 2. The Bluetooth Wizard screen will prompt. Please follow the onscreen instructions.
Targus Bluetooth Comfort Laser Mouse 3. Power on the mouse and it will automactically go into discovery mode. Click Next to continue pairing and the computer will search for the mouse. (Windows XP) 7INDOWS 6ISTA 4. The confirmation window will appear after the computer finishes detecting the Bluetooth devices. Select the Bluetooth Wireless Mouse and click Next to continue. (There may be one or more different Bluetooth devices detected.
Targus Bluetooth Comfort Laser Mouse 5. After selecting the correct device, the computer will finish establishing the connection. Please wait until the setup is completed.
Targus Bluetooth Comfort Laser Mouse Connecting with Bluetooth Software: 4/3()"! 7INDOWS 6ISTA 1. Double click on the Bluetooth Manager icon in the system tray, and then click Add New Connection. 2. Power on the mouse and it will automactically go into discovery mode. Click Next to continue pairing and the computer will search for the mouse.
Targus Bluetooth Comfort Laser Mouse 3. The computer will now search for the Bluetooth mouse and other Bluetooth devices. Please wait until the search is completed. Choose the device you wish to connect. There may be more than one Bluetooth device detected. Select Bluetooth Wireless Mouse and click Next to continue. If the mouse is not detected, please make sure the mouse is in discovery mode and click Refresh. 4. The computer will begin connecting with the device.
Targus Bluetooth Comfort Laser Mouse 5. The connection is established and setup is complete. The device is ready to use. If the connection is not successful, please click Back and search the device again. You can continue to add other Bluetooth devices or close the window.
Targus Bluetooth Comfort Laser Mouse Bluetooth Software: Mac 1. Go to the Bluetooth icon located on your desktop or in the system bar and click the ICON TO BEGIN SETUP 3ELECT h4URN "LUETOOTH /Nv TO ACTIVATE THE "LUETOOTH FUNCTION on your Mac. 3CROLL DOWN THE LIST AND SELECT h3ET UP "LUETOOTH $EVICE v 3. The Bluetooth Setup Assistant will begin. Please follow the on-screen instructions.
Targus Bluetooth Comfort Laser Mouse 3ELECT hMOUSEv AND CLICK CONTINUE TO PROCEED WITH SETUP 9OUR MOUSE WILL NEED TO BE IN hDISCOVERYv MODE TO CONNECT 0OWER ON THE MOUSE AND IT WILL AUTOMACTICALLY GO into discovery mode. 9OUR COMPUTER WILL BEGIN TO SEARCH FOR THE MOUSE /NCE THE MOUSE IS FOUND IT WILL show up in the list. Highlight your mouse and press continue.
Targus Bluetooth Comfort Laser Mouse 6. The Bluetooth mouse will now begin pairing. Click continue to proceed. 7. Congratulations. Your Bluetooth mouse is setup and ready to use.
Targus Bluetooth Comfort Laser Mouse Programming Your Mouse 7INDOWS /NLY To access the advanced scroll wheel features you will need to download and install the software driver. This can be downloaded from the following location: 6ISIT www.targus.com to download and install the driver. /NCE INSTALLATION IS COMPLETE OPEN THE DRIVER SOFTWARE AND SELECT THE desired setting for the scroll-wheel button. Close the driver software application and you’re ready to go.
Targus Bluetooth Comfort Laser Mouse Troubleshooting The mouse is not working. s -AKE SURE THAT THE POLARITY OF THE BATTERIES IS CORRECT 4HE POSITIVE AND negative (-) ends of each battery must match the positive (+) and negative (-) connections in the battery housing. s -AKE SURE THE BATTERIES ARE CHARGED 2ECHARGE OR REPLACE IF NECESSARY s 6ERIFY THAT THE COMPUTER IS "LUETOOTH ENABLED s 6ERIFY THAT THE DEVICE DRIVERS ARE INSTALLED 1.
Targus Bluetooth Comfort Laser Mouse Technical Support For technical questions, please visit: US Australia New Zealand Internet: www.targus.com/support.asp Internet: www.targus.com/au Email: infoaust@targus.com Telephone: 1800-641-645 Telephone: 0800-633-222 Product Registration Targus recommends that you register your Targus accessory shortly after purchasing it. Go to: http://www.targus.com/registration.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Targus Bluetooth Comfort Laser Mouse CAUTION ,!3%2 2!$)!4)/. $/ ./4 34!2% ).4/ 4(% "%!- /2 6)%7 $)2%#4,9 7)4( /04)#!, ).3425-%.43 #,!33 ) ,!3%2 02/$5#4 .%6%2 0/).4 ! ,!3%2 "%!- ).4/ ! 0%23/. 3 %9%3 /2 6)%7 ! ,!3%2 "%!$)2%#4,9 !3 02/,/.'%$ %80/352% #!. "% (!:!2$/53 4/ 4(% %9%3 -/-%.4!29 %80/352% &2/- ! ,!3%2 0/).4%2 35#( !3 !. ).!$6%24%.4 37%%0 /& 4(% ,)'(4 !#2/33 ! 0%23/. 3 %9%3 -!9 #!53% 4%-0/2!29 &,!3( ",).$.%33 3)-),!2 4/ 4(% %&&%#4 /& ! #!-%2! &,!3( "5," !,4(/5'( 4()3 #/.$)4)/. )3 4%-0/2!29 )4 #!.