® INSTALL GUIDE TUNet PP-1316 Sept 18, 2011 KT-109967 ITRON SENTINEL® METER READER Tantalus Systems Corp. 301– 3480 Gilmore Way Burnaby BC V5G 4Y1 Canada p 604.299.0458 | f 604.451.4111 www.tantalus.
LEGAL NOTICES This Guide, and any associated software, is being provided to you only as a licensee pursuant to legal agreements with Tantalus Systems Corp. that govern your rights and all other aspects of the relationship, and prevail over the legal notices herein to the extent of any inconsistency. INFORMATION SUBJECT TO CHANGE The products and methods described in this Guide are the subject of continuous development and so the information contained herein may change without notice.
REGULATORY NOTICES FCC Part 15 Notice, USA The transceiver described herein complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. The device may not cause harmful interference. 2. The device must accept any interference received, including interference that may cause undesired operation. The device is specifically designed to be used under Section 15.247 of the FCC Rules and Regulations.
Table of Contents 1 :: Product Description.............................................................................................................................. 1 1.1 Product Specification: PP-1316 C&I Meter Reader ................................................................... 2 2 :: Installing the PP-1316 ........................................................................................................................... 3 2.1 Equipment Required........................................
1 :: Product Description The Tantalus PP-1316 Itron SENTINEL® Meter Reader joins the wireless connectivity of an Itron SENTINEL® Commercial and Industrial 3 phase meter to the metering features of the TUNet communication system fixed network.
1.1 Product Specification: PP-1316 C&I Meter Reader Frequency Range Operating Temperature Modulation Power Consumption Operating Humidity 900 MHz Antenna (Part 15) Standards Page 2 902-928 MHz frequency hopping, license exempt -22 to 140°F (-30 to +60°C) FSK Active Power: 2 watts 5% to 95% non-condensing Antenna within sealed meter not accessible to installer/operator. • • • FCC CFR Title 47 Part 15c (Intentional Radiators) ANSI C12.
2 :: Installing the PP-1316 Before the PP-1316 can be installed, the Itron SENTINEL® must be programmed with initial configuration settings. Warning Energized meters, meter sockets and distribution lines present the risk of electrical shock. All work on this equipment should be performed by qualified metering specialists or industrial electricians. Personnel working with this equipment should follow all utility company established operation and safety procedures. 2.
2.2 Installing PP-1316 Components PP-1316 Components List (Separate Assemblies) The PP-1316 is compatible with all Itron SENTINEL® meter forms. The following parts are supplied with the PP-1316 installation kit: 1. Tantalus communication module, P/N 120-0215 2. Tantalus antenna bracket, P/N 260-0055 PP-1316 Components List (Single Assembly) 1. Page 4 Tantalus communication module, P/N 120-0215-A Tantalus Systems Corp.
2.2.1 Installing PP-1316 Components into the Itron SENTINEL® Meter 1. Remove the outer plastic cover from the Itron SENTINEL®. 2. Unclip the Itron SENTINEL® display housing from its base by gently lifting the snap features in two locations. 3. Slightly tilt the display housing away from the base to disengage the two pieces. 4. Locate the set of four parallel ridges inside the display housing. TUNet PP-1316 Install Guide Doc No.
5. Insert the Tantalus communications module ribbon cable between the two outer ridges. The ribbon cable should fit snugly between the two ridges. 6. Firmly press the ribbon cable connector against the mating header underneath the Itron SENTINEL® communications board.
7. Situate the PP-1316 module within the cavity inside the display housing. Ensure that the clip on the top of the display housing is used to lock down the PP-1316 module. 8. Ensure that the coaxial cable falls within the hole on the side of the display housing. 9. Snap the display housing back on the base of the meter. Ensure that all four outer snaps are engaged. TUNet PP-1316 Install Guide Doc No.
10. Snap the Tantalus bracket on the top of the meter. Also, there is a clip on the side of the bracket which guides the coaxial cable. Ensure the coaxial cable is placed inside the clip. If the coaxial cable has SMA RF connectors, mate them together. 11. Place the outer cover back over the Itron SENTINEL® meter. Page 8 Tantalus Systems Corp.
2.3 Configuring the Meter **** TBD **** TUNet PP-1316 Install Guide Doc No.
3 :: Contact Information Tantalus Systems Corp. Tantalus Systems Corp. 301 – 3480 Gilmore Way Burnaby, BC Canada V5G 4Y1 T/ 604.299.0458 F/ 604.451.4111 TECHNICAL SUPPORT TantalusTechSupport@tantalus.com GENERAL ENQUIRIES Info@tantalus.com Page 10 Tantalus Systems Corp.