AS-1 READER/WRITER User Manual Rev.1.0 1/9 AS-1 READER/WRITER User Manual Rev.1.0 TAKUMA SEIKO CO., LTD TEL +81-46-239-0755 FAX +81-46-239-0750 Rev.1.0 TAKUMA SEIKO CO.
AS-1 READER/WRITER User Manual Rev.1.0 2 / 9 Contents 1 Introduction ........................................................................................................................................... 3 2 Appearance............................................................................................................................................. 3 3 Specification ...........................................................................................................................
AS-1 READER/WRITER User Manual Rev.1.0 3 / 9 1 Introduction This address sensor unit (AS-1) is a RFID low-frequency (LF) 134.2kHz reader/writer unit for address tag for AGV (Automated Guided Vehicle) with internal loop antenna. Address tags are used by the AGV to determine its position while driving. AS-1 has two types of the functions by factory default, AS-1 READER is the RFID reader function, AS-1 WRITER is the RFID writer function.
AS-1 READER/WRITER User Manual Rev.1.0 4 / 9 4 Part names 4.1 AS-1 READER CN1 4.2 AS-1 WRITER CN1 CN4 Rev.1.0 TAKUMA SEIKO CO.
AS-1 READER/WRITER User Manual Rev.1.0 5 / 9 5 Interface 5.1 AS-1 READER CN1 (JST B12B-PH-K-S) Pin No. Pin Name Function Description 1 GND - 2 DC +12V Power 3 /Stop I RF output stop signal to sleep (L: Stop mode) 4 /Clock O Data enable signal (100msec) for Data 5 /D7 O Data bit 7 6 /D6 O Data bit 6 7 /D5 O Data bit 5 8 /D4 O Data bit 4 9 /D3 O Data bit 3 10 /D2 O Data bit 2 11 /D1 O Data bit 1 12 /D0 O Data bit 0 Ground Rev.1.0 TAKUMA SEIKO CO.
AS-1 READER/WRITER User Manual Rev.1.0 6 / 9 5.2 AS-1 WRITER CN1 (JST B12B-PH-K-S) Pin No.
AS-1 READER/WRITER User Manual Rev.1.0 7 / 9 6 Operation 6.1 AS-1 READER Normal operation: - Turn on the power. - AS-1 READER can be read ID value (D7-D0) from RFID tag with /Clock = L. - User system will be known an ID value by /Clock = L 100msec width. Stop mode: - AS-1 READER can be entered stop mode (low power consumption) by /Stop = L. - Recommendation: If the AGV is not moving, set Stop mode (/Stop = L). 6.2 AS-1 WRITER Write operation: - Turn on the power.
AS-1 READER/WRITER User Manual Rev.1.0 8 / 9 Read operation: - Turn on the power. - Put AS-1 WRITER above the ID tag you want to read. - Set R/W switch to READ side. - Press the EXE button. - If reading was succeeded, ID address number will present on LCD display. ― ― ― Read mode ― ― ― Rd ADRS: xxx If reading was succeeded, EXE LED will light 100msec. If reading was failed, LCD display will present Rd ADRS: xxx . During read operation, CLEAR, UP, X10, DOWN button disabled.
AS-1 READER/WRITER User Manual Rev.1.0 9 / 9 7 REGULATORY COMPLIANCE INFORMATION Product Name: Address sensor unit Model Name : AS-1 READER, AS-1 WRITER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TOMITA U.S.A INC. (HEADQUARTERS) 7801 Corporate Blvd. Ste. G, Plain City, OH.