Smart Watch Model No.: T1 User Manual Thank you for choosing our product. For safe and optimal use of the watch, please, read this guide carefully before getting started.
Warnings and safety instructions Please, do NOT take out the SIM card when the watch is powered on. It could cause damage to the watch. Keep the watch away from fire and avoid high temperature environments. The watch does not prevent data roaming. It can create expensive data traffic when used in a different country with the same SIM card. The watch and the mobile app are continuously developed. Their functions and language can slightly differ from this manual. Use this document as a reference only.
2 Charging the watch Remove the watch and the charging cable from the packaging. Connect the magnetic head of the cable to the metallic contacts on the back of the watch (rotate the connector until the magnets pull it in position) and connect the other end of the cable to a USB power source. Charging the watch to its full capacity normally takes 2-3 hours. You can see the dynamic battery icon on the screen to judge whether it is fully charged.
Insert Push far inside until can't push anymore. Secure the SIM card slot with screws to prevent it from falling out and water damage. Note: after you insert the sim card and turn on the watch and wait 1-2 minutes, if under time display interface , move finger from top to end to see a setting interface , you can see if have symbol display on watch ,if not ,the watch may not support your telecom operator. please contact the distributor to check with your sim card APN setting.
After the guardian added the watch on app,and for watch ,after you see the symbol on watch, hold the button more than 3 seconds , the watch will call first 4 phone numbers in the contact list in turn for 3 times. Press the button to cancel the calling. (3)Answer the call When there is a calling on watch , touch the phone calling symbol to answer the call . (4)Hang up the call When talking finished, touch the hang up symbol to hang up.
make the call , touch image to make the call , touch the hang up symbol to hang up the calling . Voice message menu: Touch Chat to enter submenu, slide to choose the phone number which you want to send a voice message ,Touch to enter submenu and see a recording image ,Hold to record , remove to send message. Camera Touch Camera to enter ,Touch the symbol to take a picture , press V to confirm sending,slide to choose the phone number to send the picture .
4.Operating the mobile application With nano sim card installed in watch and watch powered on, wait till see the symbol on watch display, now you can start using the application. Please, follow the steps below. 4.1 Downloading the mobile application Please, search for and install one of the following software: For Apple phones, search for “TAKIT GPS PRO” in the App Store. For android phones, search for “TAKIT GPS PLUS” in the Google Play store.
that can communicate with the watch. Note: in countries where the local mobile number starts with a zero (0), please, register with an email address. The verification code cannot be sent to these kinds of phone numbers. If you select Email, the verification code will be sent to you in an email. Note: if you do not receive the email with the verification code, please, check your spam box or spam quarantine. 4.
2. There are two ways to register the watch. Either by scanning its QR code or by manually entering its CID: To scan the QR code: Tap the middle of the screen to start the camera (allow using the camera if asked). Now scan the QR code that is on the back of your watch or on the outside of its packaging. Move the QR code towards or away from the phone until it is read automatically. To enter the CID number: Tap enter CID, type in the CID number and then tap OK.
The Map screen is also the first screen you see when you start the software. When started, the software shows all connected watchs on the map. You can slide head image any of the watchs to communicate with. to select The software uses Google Maps to locate the watchs. To better understand the location of the watchs, you are offered three map visualization modes: Satellite, 2D and 3D. Tap to switch between these options.
Tap to change the application language and check the application version Tap to choose call or monitor watch Tap to see your number of steps, Tap to see the heart rate ,tap at the heart rate interface to off/on the heart rate monitor and set the frequency.You can also touch on the watch to see your heart rate,the results will also upload and show on the APP. 4.4.2.1Call and Monitor Tap call to start a phone call ,Tap Monitor to listen the watch.
appear on the icon Message. Tap to check new messages or alerts. Press and hold to speak, then release the send voice message. Tap to start remote take photo on watch,the watch will take a photo now and send to you,wait for seconds,then you can receive the picture. 4.4.3.3Contacts and administrator Tap Contacts to see the list of phones and users linked to the watch. The administrator of the watch is displayed at the top.
(3)Mute: You can set up multiple time intervals when the watch will remain silent even if there is an incoming call or message. (4) Location mode: You can choose between two options: Smart mode: the watch location is updated automatically when the watch is moving outside. Manual mode: the location will only be updated when you tap the Loc button on the Map screen. Note: Automatic mode uses more battery.
(1) I cannot turn on the watch The battery in your watch might have run out of power. Please, connect the watch to a power source until fully charged and then try again. (2)I cannot scan the QR code The following methods can help your phone read the QR code: If the ambient light is low, move to a brighter area and retry scanning the QR code.
Note: only Backup administrators can receive the administrator right. Other added phone numbers cannot. (5)How to delete a previously added phone number? Only the administrator can delete phone numbers. Open the mobile application. Log on as the administrator of the watch. Open the master list of the selected watch in the Main menu. Tap and hold one of the numbers in the list. Tap Delete in the popup menu and confirm your choice.
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.