User Guide

1
Our sincere gratitude
6-2: The installation marks on the secure groove
Before using this product on your consumer electronic products,
please check Takeway ® R1 ranger clampod and its accessories for
damage or deformity. If there is any, please contact the salesperson
to exchange your product to prevent damage of your consumer
electronic products or personal injury caused by the flawed product.
The company takes no responsibility and assumes no liability for the
loss or inconvenience caused by user’s own negligence.
2
Please test the relevant components
and read responsibility statement
before using this product
4
Operation notes
3
Product components
4-5: If the product has not been used for a long time, please check
the components and functions work normally, so that it does not fall
when it is used on the electronic products.
4-6: After the product is assembled, please place it on a flat surface
to check for its stability. When using this product for standing
shooting, do not remove your hands from your electronic product
when installing it on the clamp. Make sure that the clampod stands
firmly on the surface before shooting, so that your electronic product
will not be damaged caused by the fall of the clampod.
4-7: Please follow the installation instruction below when utilizing this
product. First, clamp and secure the R1 Ranger Clampod, then use
the attached quick release clip to mount your electronic device and
prevent your device from falling and getting damaged.
4-8: When installing the quick release plate to electronic devices or
accessories, please make sure that the quick release plate is
screwed in tightly to prevent it from loosening and falling.
The secure groove is designed to increase stability and to
prevent the quick release clip from loosening. Installation marks
are marked on the quick release parts to ensure fast and
accurate installation.
To choose a proper usage for clamping, please refer to 6-3-2:
Clamping Range. When clamping smooth cylindrical surface,
please refer to 6-1-2: Using the anti-slip mat.
6-3: Use of the inner jaw
For better convenience and stability, use the inner jaw to secure
the object when clamping the R1 Ranger Clampod on small tubes.
The inner jaw is made of high-grade, high-strength reinforced
plastic. The jaw comes installed in the clamp from the factory. Do
not remove inner jaw unless necessary to prevent the jaw from
being lost.
6-2-1: Line up the installation
marks on both the quick release
clip and the mounting platform
(attached to the accessories or
electronic devices) and tighten the
quick release knob to complete
installation.
As the figure shows, store the
anti-slip mat between the
quick release knob and the
mounting platform.
used on a slippery surface
5
Parts name
Mounting
Platform
Quick Release
Knob
Diamond
Symbol
Jaw
Inner Jaw
Clamp Body
Labor-Saving
Handle
Quick Releace
Clip
Secure Groove
Ballhead Secure Groove
Stripes
side :
used on a flat surface
Smooth
side :
used on a cylinder surface
used on a slippery and
cylinder surface
The inner jaw can be easily deployed and
stored; it allows users to clamp it on a
small cylinder or a poll firmly. Its range is
between
ø
10mm to 16mm.
U side :
5
7
6
Indicator Mark “J”
8
Pad
9
10
Anti-slip mat
10
1
2
3
4
Jaw
3
6-1-1: Storing the anti-slip mat
As the figure shows, wrap the
anti-slip mat on the 6-1-2
cylinder to be gripped. Then use
the square jaw to clamp the
anti-slip mat to increase grip.
6-1-2: Using the anti-slip mat
Inner Jaw
4
6-4: Instructions for clampod usage
6-4-1
T-RC02
6-4-1: Clamp and secure the
clampod on the object to be
gripped. As shown in the figure,
the convenient handle fixing
point can be bent for more flexible
application in limited space. This
also can be rapidly and
conveniently done with less effort.
4-1: When using on a flat surface, use the grid side of the clampod for
stability or use the smooth side of the clamp to protect the surface
from damaging.
4-2: When clamping on a smooth cylindrical surface, place the
anti-slip mat between the surface and the clampod to increase grip.
4-3: The body of the clamp is made of aluminium alloy, but do not
place the product in a humid environment for a long time to avoid
product being damaged.
4-4: Do not place the product near heat or open flame which will
damage the plastic components.
6-2-1
5
1
2
7
7
Move the securing position of the
inner jaw downward to the center
to attach to cylinders. After
securing, shake gently to make
sure it is tight to prevent items
from coming loose and falling.
6-3-1: Use with inner jaw
This product comes with a clamp indicator mark. When
clamping exceeds the mark as shown in the below diagram, the
inner jaw can be used to clamp the cylinder and maintain
stability.
6-3-2: Clamping range
* When you see the “J”
indicator mark (Ø10 ~
Ø16mm), use the jaw and the
inner jaw to make a "3 J-point
clamp" (please note the "J"
mark on the jaw).
When you can’t see the
“J” indicator mark (Ø17~
Ø32mm), use the inner
parts of the clamp body
for clamping. At this time
the inner jaw should be
folded
The T-B01 Ballhead in this installation instruction is an accessory
designed for T1 Clampod and is sold separately.
6-5: T-B01 Ballhead installation and use
(optional accessories)
6-5-1: Loosen the quick
release knob and remove the
quick release clip.
5
1
6-4-2
6-4-2: Clamp the R1 Ranger
Clampod to a proper location
and shake gently to make sure it
is firmly secured to prevent items
from loosening and falling.
7
10
5
2
10
3
6-1: Anti-slip mat assembly, disassembly and storage
6
Assembly and operation
Assemble and place the anti-slip mat in between a smooth cylindrical
surface and the R1 Ranger Clampod to increase stability of the clampod
and to avoid sliding. The mat can also be stored between the Quick
release knob and the mounting platform to prevent it from getting lost.
1
1
2
5
Clamp body with
T-IJ02 inner jaw
User guideAnti-slip mat
Takeway® R1 Ranger Clampod is another revolutionary
breakthrough after T1 Clampod. The ultra-lightweight R1 Ranger
Clampod is built for the “outdoor enthusiasts” group. The R1 Ranger
Clampod weighs only 73g and is portable and convenient to use for
consumer electronics such as action cameras, smartphones and
tablets. R1 Ranger Clampod can be easily dissembled without tools
and has a maximum load capacity of 3kg. The R1 will not loosen even
when it is used while moving around, and can be matched with
different accessories. This provides users with versatility based on
user requirements. Not only can it be clamped on to tubes, it can also
be secured on flat surfaces and be placed in pockets. Even extreme
sports will not affect its function, so enjoy every moment and explore
new experiences with Takeway® R1 Ranger Clampod!
1
Before using the product for the first time, please read through the user guide.
Please use this product correctly after fully understanding the content of the user guide.
USER GUIDE
RANGER
6-1-1
6-1-2
10
10
2
T-IJ02
3
6-3-1
6-5-1
1
5
5