User's Guide

2
KEYPAD
1. Unlocks the lockset by entering a valid User Code.
2. Programs the lockset by entering a valid Programming Code in
Programming Mode.
G00-KPDBJ13 Rev. 19/06-00
USER GUIDE
1
OVERVIEW OF THE LOCKSET
OR
1
HOW TO LOCK / UNLOCK THE LOCKSET
2
HOW TO LOCK / UNLOCK / PROGRAM THE LOCKSET
2
HOW TO PROGRAM THE LOCKSET
・The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds.
・3 Beeps means something was entered incorrectly. Please redo the step again.
1
1. Lock or unlock the lockset by a valid key.
3
MECHANICAL KEYWAY OVERRIDE
Volume Control
Auto-lock
・Turn on / off door lock operation volume.
・Volume is always on in the programming mode.
・Default Auto-lock Delay Timer : 10 seconds.
・Auto-lock Delay Timer range: 10 -99 seconds.
Auto-lock Delay Timer
Vacation Mode
・Vaction mode temporarily disable ALL User Codes.
Add Single-entry Code(s)
・Single-use User Code can only be used once to unlock the lockset.
・Single-use User Code capacity: 5 sets (4 digits).
・Auto-lock is disabled by default.
BASIC SETTINGS
ADVANCED SETTINGS
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
ENTER / LOCK BUTTON
7
0
2
1
Programming Code
(6 digits)
5
0
Programming Code
(6 digits)
6
0
Programming Code
(6 digits)
8
0
Programming Code
(6 digits)
Programming Code
(6 digits)
Enter New Amount
(10 - 99)
Single-entry Code
(4 digits)
1
Turn On
0
Turn Off
1
Turn On
0
Turn Off
1
Turn On
0
Turn Off
1. Red light: Represents an incorrect entry or the unit is
programming mode.
2. Yellow light: Flashes when the batteries are low in power.
3. Green light: Represents a correct entry.
4. Press to activate or lock the lockset.
Delete all User / Single-entry
Codes
・Delete all User & Single-entry Codes.
Programming Code
(6 digits)
4 0
Press [SET] for
1 second.
Press [SET] for
1 second.
Press [SET] for
1 second.
Press [SET] for
1 second.
Press [SET] for
1 second.
Press [SET] for
1 second.
Change Programming Code
・Programming Code can be used to program or unlock the lockset.
・The default Programming Code is “123456”.
Programming Code
(6 digits)
New Programming
Code(6 digits)
1
0
Press [SET] for
1 second.
Add a User Code(S)
・User Code can be used to unlock the lockset.
・User Code cappcity: 10 sets (4-6 digits).
New User Code
(4-6 digits)
2
0
Programming Code
(6 digits)
Press [SET] for
1 second.
Add another code
Add another code
Delete individual User
/ Single-entry Code(s)
・Delete individual User Code(s).
3
0
Programming Code
(6 digits)
User Code / Single-entry
Code (4-6 digits)
Press [SET] for
1 second.
Delete another code
1. Protects the batteries from unexpected damage.
4
BATTERY COVER
5
[SET] BUTTON
1. Press set button for 1 second to enter programming mode.
2. Please refer to for more information about
programming mode.
2
2
-
1. Locks or unlocks the lockset manually.
INTERIOR THUMBTURN
6
Include / Exclude to Z-Wave
network
ve
・Turn on inclusion / exclusion mode at your Z-Wave controller
when including / excluding the lock.
・Refer to your Z-Wave controller instruction for more information.
9
0
Programming Code
(6 digits)
Press [SET] for
1 second.
Include / Exclude unsuccessfully (beep x 3)
Include / Exclude successfully (beep x 1)
OR
If you should input DSK (Device Security Key) to
complete the inclusion, please find the DSK
on the inner side of the battery cover.
Z-Wave :
* * * * *
Enter valid User Code or
Programming Code.
Keypad is temporarily disabled for 1 minute after 4 consecutive incorrect entries.
To lock
To unlock
Press “ ”
to lock.
→
OR
OR
OR
Use a mechanical
key to lock.
→
Use a mechanical key
to unlock.
Lock or unlock by
mobile app.
1
2
3
4
6
7
8
9
5
0
OR
Lock or unlock by
mobile app.
1
2
3
4
6
7
8
9
5
0