User's Manual

1. Please always press button to cancel any typo or exit
programming mode.
2
CLEAR BUTTON
G00-TPDBF13 Rev. 15/08-00
USER GUIDE
1
OVERVIEW OF THE LOCKSET
OR
1
HOW TO LOCK / UNLOCK THE LOCKSET
2
HOW TO LOCK / UNLOCK / PROGRAM THE LOCKSET
The screen is temporarily disabled after 4 consecutive incorrect entries.
To unlock, enter valid User Code or Programming Code.
After the screen is activated, enter Guiding Code first if it is on (see - ).
2
2
Touch the screen to lock.
1 2 3
4 5 6
7 8 9
c
0
Lock or unlock by mobile app.
To lock
To unlock
A
A
→
Use a mechanical key to lock.
B C
→
Use a mechanical key to lock.
B
Lock or unlock by mobile app.
C
2
HOW TO PROGRAM THE LOCKSET
・The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds.
・3 Beeps means something was entered incorrectly. Please redo the step again.
1. Protects the batteries from unexpected damage.
4
BATTERY COVER
5
[SET] BUTTON
1. Press set button for 1 second to enter programming mode.
2. Please refer to for more information about
programming mode.
2
2
-
1. Locks or unlocks the lockset manually.
INTERIOR THUMBTURN
6
INDICATORS
1
1. Red light: Represents an incorrect entry or the unit is
programming mode.
2. Yellow light: Flashes when the batteries are low in power.
3. Green light: Represents a correct entry.
1. To unlock the lockset by a valid key.
3
MECHANICAL KEYWAY OVERRIDE
C
Change Programming Code
Add a User Code(S)
・Programming Code can be used to program or unlock the lockset.
・The default Programming Code is “12345678”.
・User Code can be used to unlock the lockset.
・User Code cappcity: 25 sets (4-8 digits).
#
# #
#
1
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
New Programming
Code(4~8 digits)
Same New Programming
Code(4~8 digits)
New User Code
(4-8 digits)
#
#
2
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
# #
Same New User
Code (4-8 digits)
Add another code
Delete individual User Code(S)
・Delete individual User Code(s).
Delete ALL User Codes
・Delete ALL User Codes at once.
C
#
#
4
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
Volume Control
Guiding Code
Include / Exclude to Z-Wave
network
Auto-lock
・Guiding Code is a set of random codes to be entered prior to any
User Code to prevent code probing by placing finger prints on
every button making code discovery more difficult.
・Turn on / off door lock operation volume.
・Volume is always on in the programming mode.
・Turn on inclusion / exclusion mode at your Z-Wave controller
when including / excluding the lock.
・Refer to your Z-Wave controller instruction for more information.
・Default Auto-lock Delay Timer : 10 seconds.
・Auto-lock Delay Timer range: 10 -99 seconds.
Auto-lock Delay Timer
Vacation Mode
・Vaction mode temporarily disable ALL User Codes.
Add Single-use User Code(S)
・Single-use User Code can only be used once to unlock the lockset.
・Single-use User Code capacity: 4 sets (4 digits).
#
#
#
2
1
Press [SET] for
1 second.
Programming Code
(4~8 digits)
#
Add another code
Single-use
User Code (4 digits)
Same Single-use
User Code (4 digits)
1
Turn On
#
0
Turn Off
#
#
#
5
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
1
Turn On
#
0
Turn Off
#
#
#
2
2
Press [SET] for
1 second.
Programming Code
(4~8 digits)
1
Turn On
#
0
Turn Off
#
#
#
6
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
・Auto-lock is disabled by default.
1
Turn On
#
0
Turn Off
#
#
#
8
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
Enter New Amount (10 - 99)
#
#
#
7
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
BASIC SETTINGS
ADVANCED SETTINGS
#
#
9
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
Include / Exclude unsuccessfully (beep x 3)
Include / Exclude successfully (beep x 1)
OR
#
#
#
3
0
Press [SET] for
1 second.
Programming Code
(4~8 digits)
#
Delete another code
User Code Same User Code