SETUP MODE HOW TO ADD A REMOTE CONTROL {only available for Remote Control Electronic Deadbolt) Steps are as follows: 1. Press snd hold [SET] button for over 2 seconds. The Red LED wi You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button (& . Enter [20] and press bunion (8). Press ary button on the reroute control and press button (ED The Red LED will light up for 10 seconds. The locket will have the new remote control set.
SETUP MODE HOW TQ ADD A SINGLE-USE USER CODE / PROXIMITY CARD / REMOTE CONTROL Steps are as follows: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button recommend to tum on auto-lock mode according to page 38 before following the below steps to enable single-use user node/ remote control. single-use Follow the below steps.
SETUP MODE Note: . The locket wit go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. Single-use user code capacity: 5 sets maximum. Single-use remote control! capacity: 5 sets maximum. Single use proximity card capacity: 5 sets maximum. nop own Single-gantry user code! single-entry user cremate contra/ single-sentry proximity cans is only allowed to work enc and wil corner invalid after one-time use (entry). 6.
SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING USER CODE Steps are as follows: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice You are now under setup mode 2. Enter 123456 (or current programming code) and then press bunion Enter [30] and press button (& Enter existing user code (that you wish to delete) snd press button (B The Red LED wit light up for 10 seconds.
SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING PROXIMITY CARD {only available for Proximity Card Electronic Deadbolt) Steps are as folios: 1. Press snd hold [SET] button for over 2 seconds. The Red LED will light up and beep twice You are now under setup mod 2. Enter 123456 {or current programming code} snd then pass button (BD Enter [30] and press button (GB) Fut the card that you wish to delete to touch the inductive zone. The Red LED will light up for 10 seconds.
SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING REMOTE CONTROL {only available for Remote Control Electronic Deadbolt) Steps are 35 flows: 1. Press and hold [SET] bitten for over 2 seconds. The Red LED will light up and beep twice. You are now under setup made. Enter 123456 {or current programming code) and then press button (B) . 2. Enter [30] and piss button (& . Press any button on the remote control (that you wish to delete) and press button (B) . The Red LED will light up for 10 seconds.
SETUP MODE HOW TO DELETE ALL EXISTING USER CODES AT ONCE Steps are as follows: 1. Press and hood [SET] button for over 2 seconds. The Red LED wil light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button (BY . Enter [40] and press button (8) . Press and hold (© button untie a beep is heard The Red LED wil light up for 10 seconds. The thickset. wil delete ail existing user codes. Note: 1.
SETUP MODE HOW TO DELETE ALL EXISTING PROXIMITY CARDS / REMOTE CONTROLS AT ONCE {only available for Proximity Card Electronic Deadbolt / Remote Control Electronic Deadbolt) Steps are as follows: 1. Press and hold [SET] button for aver 2 seconds. ‘The fed LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 {or current programming code) and then press button & | Enter [41] and press button . Press and hold (ED button until beep is heard. ‘The fed LED will light up for 10 seconds.
SETUP MODE HOW TO DOABLE ALL EXISTING CODES/ CARDS/ REMOTE CONTROLS (VACATION MODE) Steps are 3s follows: Press and hood [SET] button for aver 2 seconds. Tha Red LED wil it up and neap twice. You are now under setup mode. Enter 123456 {or currant programming code} and then press button (& . Enter [50] and press bitten (@ . Enter [0] and press bitten (B> The Red LED wiki fight up for 10 seconds. The locket will turn on vacation mode. 4. Enter [1] and press button (B .
SETUP MODE HOW TO DISABLE BUTTON SOUND {MUTE MODE} Steps are ax flows: 1. Press and held [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. . Enter 123456 {or current programming code} and then press button (BY Enter [60] and press button (8). Enter [0] and press button The Red LED will light up for 10 seconds. The locket wilt turn on mute mode. 4. Enter [1] and press button CB . The Red LED will light up for 10 seconds. The locket wil tum off mute mode.
SETUP MODE HOW TO ENABLE AUTO-LOCK MODE Steps are as flows: 1. Press and hold [SET] button for over 2 seconds The Red LED wil light up and beep twice. You are now under setup mode. . Enter 123456 {or current programming code} and then press button (8) . Enter [80] and press button . . Enter [0] and press bitten (5) The Red LED wil fight up for 10 seconds. The lack set will turn on ate-lock mode. Enter [1] and press button (BD The Red LED will it up for 10 seconds. The Thickset wil tum off ate-iock mods.
SETUP MODE HOW TO SETUP AUTO-LOCK TIME DELAY Steps are as follows: 1. Press and hold [SET] button for over 2 seconds. The Red LED wit! light up and beep twice. You are now under setup mode. . Enter 123456 (or cement programming code) and then press button (B) Enter [70] and press button (> | Enter the seconds for delay time of auto-locking (10 to 90) and press button (B) . The Red LED will light up for 10 seconds. The locket wil setup auto-lock time delay. ra Note: 1.
SETUP MODE HOW TO ENABLE DOUBLE AUTHORIZATION MODE {only available for Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt) Steps ara as follows: 1. Press and hold [SET] button for aver 2 seconds. The Red LED will light up and bop twice. You are now under setup mode. . Enter 123456 (or currant programming code) and then press bitten Enter [39] and pass button (B . 3. Enter [0] and pass button CB) . The Red LED will light up for 10 seconds.
SETUP MODE HOW TO RESTORE FACTORY SETTING Taps ara as flows: 1. Ramona ons battery from the battery pack. 2. Press and hold [SET] button and put the battery back. Esp holding [SET] tuition nth a Lang beeps and 3 short beep are heard. All functions wil be stressors back ta factory setting. Hist: Far your softy, restate sectary setting tufter stemming the mc on the dear. #0 misting user sedan/ cds reeks traversals wh be dusted. Lack wil be restored to the preset programming odes of 12-34-58.
SETUP MODE HOW TO REPLACE A BATTERY OF REMOTE CONTROL Steps are as folios: 1. Loose two screws before opening the bottom shell 2. Take the PCB out. 3. Push the battery out by inserting the toc! inch the crack between the PCB and the electrode terminal. Push into the new battery. 5. Replace the PCR. pen Face the bottom shell back and tighten the resews.
OPERATION MODE HOW TO LOCK manually Pond Keypad: Press button (8) to lock the door. —_ Remote control Press lock button to lock the doer as shown. = {only available for Remote Control Electronic Deadbolt) 4 > HOW TO LOCK automatically C 1. Auto-lock mode should be muted on and outs-lock time delay should be also set up. 2. The thickset will be ate-locked in few seconds (default 10 seconds or the time you entered) after unlocking by using codes, card, or remote control.
OPERATION MODE SAFE MODE 1. The keypad will be automatically deactivated for | minute after 4 wrong attempts. 2. Wrong attempts will not be counted when you press button (© to clear previous incorrect codes before the red LED lights up. 2. The deadbolt can be locked or unlocked by 3 valid traditional key under security.
TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS The locket did not . Check center of strike hols for alignment with latch hole on the door to ensure free movement for the deadbolt. operate comely slier 2. Make sure the tailpiece is properly inserted {in the horizontal position) installation. in the latch. 3. Do [AUTOMATIC BOLT DIRECTION DETERMINATION]. | il Fee! 2 bump while 1. Please rotate the thumb tum back and forth a few times. turning of the motor? 1. Da not lock {or unpick} the door consecutively.
TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS Keypad does not respond at all. po w . Cheek to see if the batteries ame reinstalled. Check to see If the Yellow LED light is flashing or not. it means “low battery" if the light keeps flashing. Make sure the able is well-connected to the port. Programming code cannot be changed 7 ~ . Please complete the "HOW TO CHANGE PROGRAMMING CODE" process by inputting codes within 10 seconds.
TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS 1. Make sure 3ll code inputting processes should be completed within 10 seconds i cannot add a new user code. | 2. Make sure yu have snared the correct programming code. 3. The new user code wil not be accepted if 10 sets of user codes are ready stored in the memory. 1. Make sure you have enters the comet user code. What happens If the locket | 2. Check to see If the Yellow LED light is flashing or net.
TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS Red LED fight is steel on after setting is completed? . Please make sure if [SET] button is jammed. ise re-install the batteries. T Auto rock" does not function. Pieing make sure turn on auto-lock mode. . Check to see if the Yellow LED fight is flashing or not. it means "ow battery” if the light keeps flashing. ~ Yalow LED light keeps flashing.
TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS Gad mots rematch controls. 1. Plaass purchase the remote contra! (produced by cur company) from en authorized cafetiere. Other remote controls maybe not compatible with this locket. Need more proximity cards. 1 Proximity card we offer is the latest Radio Frequency identification (RFI) technology, compatible with standard Mi fare 13.56 MH. 2 You can use any card compatible with standard Mi fare 13.56 MHz or purchase new cards from an authorized retailer.
SECURITY INSTRUCTION 1. Do not share the programming code with anyone else. 2.Keep & written copy of all valid user codes in & safe place. { You may use the table below to record your information) 3. The emery capacity for user codes is 10 sets. INFORMATION PAGE 4. Ir is STRONGLY recommended changing ali codes if any security information in the table is lost.