IMPORTANT SAFETY INSTRUCTION Lad prevent damage to the finish, DO NOT use any abrasives, sharp objects or harsh chemical products containing alcohol, petroleum solvents, acids or acetone to clean this locket. To prevent damage to the sensitive electronics components, DO NOT sow any liquids to star locket while Installing or cleaning. Do not attempt to disassemble any internal components of this locket a5 this WILL void the limited warranty.
CONTENTS MAIN OPERATING INSTRUCTIONS PROGRAMMING CODE AND USER CODE COMPONENTS INSTALLATION INSTRUCTIONS —— og SETUP MODE 01. HOW TO CHANGE PROGRAMMING CODE ~ «nos ooo cm cm sou 25 02. HOW TO ADD AN USER CODE 03. HOW TO ADD A PROXIMITY CARD (RID) 04. HOW TO ADD A REMOTE CONTROL (RADII FREQUENCY, RF) -05. HOW TO ADD A SINGLE-USE USER CODE/ PROXIMITY CARD/ REMOTE CONTROL 06. HOW TO DELETE AN INDIVIDUAL EXISTING USER CODE 07. HOW TO DELETE AN INDIVIDUAL EXISTING PROXIMITY CARD 08.
CONTENTS 11. HOW TO DISABLE ALL EXISTING USER CODES / Sen 6 PROXIMITY CARDS / REMOTE CONTROLS (VACATION MODE) 12. HOW TO DISABLE BUTTON SOUND (MUTE MODE 37 13. HOW TO ENABLE AUTO-LOCK MODE 8 14. HOW TO SETUP AUTO-LOCK TIME DELAY -39 15. HOW TO ENABLE DOUBLE AUTHORIZATION MODE HOW TO RESTORE FACTORY SET TIRE 17. HOW TO REPLACE A BATTERY OF REMOTE CONTROL -- 42 OPERATION MODE 01. HOW TO LOCK (ie. TO ENABLE AUTG-LODKY vm ooo oo 43 02. HOW TO UNLOCK =m =m mmm memo memo some eoeooeeoeooe 44 U3.
MAIN OPERATING INSTRUCTIONS | This manual is intended for both Proximity Card Electronic Deadbeat and Remote Control Electronic Deadbolt, Any description which Is rested to proximity card (RID technology} can only be applied on Proximity Card Electronic Deadbolt LED Indicator | Any description which is related to remote controller (RF technology) Te ~ Keypad can only be applied on Remote Central Electronics Dssdnnir. aE Eg it Lack Button 1. Green fight: Code entered is valid.
MAIN OPERATING INSTRUCTIONS Inductive Zone & RID Card : {only available for Proximity Card Electronic Deadbolt) 1. inductive zone is around the keypad. 2. The proximity card we offer is the test Radio Frequency identification {RID} technology, compatible with standard Mi fare 13.56 MHz. 3. Unlock the door by touching the inductive Zone with the proximity card. Remote Control © {Radio Frequency, RF} {only available for Remote Control Electronic Deadbolt) = 1.
PROGRAMMING CODE AND USER CODE PROGRAMMING CODE 1. Only one programming code wil be avowed. The thickset can be programmed only by entering the programming code. 2. A programming code is restricted to §-digits in length only. The per-set programming code is 1-2-3-4-5-6 (factory setting). Please changes it before operating the thickset 3 The programming code can be used to unlock the locket. USER CODE 1. A user code can be from four (4) ta six (8) digits in length. 2.
COMPONENTS A. Exterior Assembly J. Decorative Cover B. Cable K. Adjustable Latch C. Tailpieces (Square or radius facilitate or drive-in) D. Mounting Plate L. 6/8" (18mm) Wood Screw (4) E. (32mm) Screw {1) i M. Strike Plate { { N. Reinforced Strike Plate ©. Dust Box P. 37 (76mm) Wood Screw (2) 6. Interior Assembly Q Key (2) H. 5/18" (7.8mm) Screw {2} R. Drive in Collar {Optional} §. Bottom Plate (Optional) i. 13/16" {20mm} Screw {1) T. Square or Radius Favorite {Optional} u .
INSTALLATION INSTRUCTIONS 8 #ark the Door with a Template Sheet {attached separately} Note: If the door is per-drilied, please begin with page 13. als TEMPLATE to mark centering on door for for deadbolt shout 150 mem) samovar the existing knob or lever. b.Stand 50 door swings towards you. Allen template on starling and fold template as shown. Center line Mark the door edge approximately vam $0 158 mm } above the entry neh of ravel.
INSTALLATION INSTRUCTIONS | 2 ETT Select a backseat. Mark and drill pilot holes as shown below.
INSTALLATION INSTRUCTIONS DRILL HOLES &Dr if a hole on the door face from both sides to avoid wood spitting
INSTALLATION INSTRUCTIONS DRILL HOLES burrito hole on the door edge for the latch. ©. Use the face plate 23 @ template for mortise and pilot holes. Chisel 1/87( 3 mem) deep Face plate shooed fit gush. d. install the appropriate latch type 35 shown below. (b) pr Note: For a drive-in [titch, please refer to page 14.
INSTALLATION INSTRUCTIONS LATCH BACKSEAT ADJUSTMENT Latch backstop adjustment only sends to be made If your door needs 8 backseat. Pisa's follow diagrams below as referee. { Skip this your door hes a backs st ) 1.
INSTALLATION INSTRUCTIONS DRIVE-IN COLLAR or FACE PLATE ADJUSTMENT In addition to 70 mm ) adjustable backseat, you may change the face plate to drive-in coral. (f your door is nat a drive-in latch type, please skip this step.) oho re Wy” Note: Reverse the above steps If you need fo change the drive-in collar fo the face plate.
INSTALLATION INSTRUCTIONS INSTALL LATCH IN MORTISED AREA OR INSTALL DRIVE-IN LATCH if the door is designed for a standard type latch, please install the itch with 13/16” (20mm) screws provided. If a drive-in latch is used, please tap it into the appropriate position. Pp pg yr Face plate o Drive-in Latch Tap Latch Flush Wood Block {not included) "(see [fi before installation of drive-in latch) Backseat 13/16” {20 mm) screws Mote: Make sure that the latch moves inch and out of the strike plate smoothly.
INSTALLATION (INSTRUCTIONS 2} veil 2 5/157 (0 8mm) hole on the road when the screw post is installed.
INSTALLATION INSTRUCTIONS | | Side cabin through the notch of meting pate \ X +" The bulged part of mounting plate must face toward the door.
INSTALLATION INSTRUCTIONS Make sure the mounting plate is para lie’ with the edge of tre door. Fasten the mounting plate with 2.1787 (Summed) scrawl and (32mm) soreness. Mote: Screw (E} Is an optional screw. We recommend using screw (E} for the slab lily of the socket.
INSTALLATION INSTRUCTIONS Be REMOVE THE DECORATIVE COVER 1. Held on the lip of the 2. Put the thumbs on 3. Remove the decorative cover decorative cover. the thumb tum. by pushing the thumb.
INSTALLATION INSTRUCTIONS Connect the cable Into the connector port Balmy. The metal connector aids should face outside. Ue le Hate: = The red portion of the cable is signed with the red portion of the connector port.
INSTALLATION INSTRUCTIONS AUTOMATIC BOLT DIRECTION DETERMINATION Iota: After staling the rock on the door, do the bolt direction determination first and then restore it to the factory setting. 1. Press and hold [SET] button for over 2 seconds. The Red LED wil it up and beep twice. You are now under setup mode. 2. Enter 123456 {or cement programming code) and then press (BD button Enter [00] and press (2) button. The died LED will light up for 10 seconds. The locket wil have the bolt direction set.
INSTALLATION INSTRUCTIONS We recommend to re-install the decorative cover after completing setup mode in page 25 to page 42. if you want to remove the decorative cover, grease hold the bottom of the decorative cover and put it toward yours.
SETUP MODE HOW TO CHANGE PROGRAMMING CODE important The per-set programming sods bb 123 456. Pleats change the programming code bafflers operating the locket Steps are as follows: 1. Rags and hold [SET] button for over 2 seconds. Tha Red LED wil light up and esp twice. You ar now under setup mods. 2. Enter 123456 (or current programming Coda) and then press button Enter [10] and press button (BD). Enter new programming cod (six digits) and pass button (83 . The Red LED wil light up for 10 seconds.
SETUP MODE HOW TO ADD AN USER CODE Steps are 35 follows: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up snd esp twice. You are now under setup mode. . Enter 123456 (or currant programming code) and then press button (BD. Enter [20]and press button Enter new user code (four to six digits) and press button GB © The fed LED will light up for 10 seconds. The locket wil have the new user code set.
SETUP MODE HOW TO ADD A PROXIMITY CARD {only available for Proximity Card Electronic Deadbolt} Steps are as follows: . Press and hold [SET] button for over 2 seconds. The Red LED wit: it up and beep twice You are now under setup mode. . Enter 123456 (or current programming code) and then press button CBD Enter [20] and press button (B) . Touch the inductive zone with the card. The Red LED will it up for 10 seconds. The locket will have the new card set.