P1. WARNING 1. To prevent damage to the finish, DO NOT use any abrasives, sharp objects or harsh chemical products containing alcohol, petroleum solvents, acids or acetone to clean this lockset. 2. To prevent damage to the sensitive electronic components, DO NOT allow any liquids to enter lockset while installing or cleaning. CAUTION! 1. Do not attempt to disassemble any internal components of this lockset as this WILL void the limited warranty. 2.
P2. CONTENTS MAIN OPERATING INSTRUCTIONS.....................................................................................03 PROGRAMMING CODE AND USER CODE..........................................................................05 COMPONENTS............................................................................................................................06 INSTALLATION INSTRUCTIONS...........................................................................................08 SETUP MODE 01.
P3. MAIN OPERATING INSTRUCTIONS LED indicator Keypad Lock button Cancel button Key override Thumbturn This manual is intended for Electronic Deadbolt Lock/ Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt. Please be advised that this manual is set up for this specific unit and is not to be used with any other product.
LED Indicator 1. Green light: Code entered is valid. 2. Red light: Code entered is invalid/ Under setup mode. 3. Yellow light: Low battery warning. * All batteries should be replaced if yellow light flashes. Keypad 1. To unlock the lockset by entering a valid code. 2. To program the lockset. 3. 4. When mis-typing codes during any process, press Cancel button to cancel the wrong codes and re-enter the correct codes if the yellow light is on or keeps flashing. To lock the lockset by pressing Lock button.
P4. MAIN OPERATING INSTRUCTIONS Inductive Zone LED Lock button Unlock button Inductive Zone (only available for Proximity Card Electronic Deadbolt) 1. Inductive zone is around the keypad. 2. The proximity card we offer is the latest Radio Frequency Identification (RFID) technology, compatible with standard Mifare -13.56 MHz. 3. Please contact the proximity card with the inductive zone. Remote Control (Radio Frequency, RF) (only available for Remote Control Electronic Deadbolt) 1. 2. 3.
P5. PROGRAMMING CODE AND USER CODE PROGRAMMING CODE 1. Only one programming code will be allowed, and the lockset can be programmed by entering the programming code. 2. A programming code is restricted to 6-digits in length only. The pre-set programming code is 1-2-3-4-5-6 (factory setting), please change it before operating the lockset. 3. The lockset can be unlocked by entering programming code. USER CODE 1. A user code can be from four (4) to six (6) digits in length. 2.
P6. COMPONENTS U A. B. C. D.
P7. E. F. G. H. I. J. K. L. M. N. O. P. Q. 1-1/4" (32mm) Screw (1) 2-1/8" (54mm) Mounting Bolt (2) Interior Assembly 5/16" (7.8mm) Screw (2) 13/16" (20mm) Screw (1) Decorative Cover Adjustable Latch (Square or radius faceplate or drive-in) 6/8" (19mm) Wood Screw (4) Strike Plate Reinforced Strike Plate Dust Box 3" (76mm) Wood Screw (2) Key (2) R. S. T. U.
P8.
P9.
P10.
P11.
P12.
P13.
P14.
P15.
P16. INSTALLATION INSTRUCTIONS: COMBINE THE EXTERIOR ASSEMBLY WITH LATCH Drill a 5/16”(ø8mm) hole on the door when the screw post is installed.
P17.
P18. INSTALLATION INSTRUCTION Make sure the mounting plate is parallel with the edge of the door Fasten the mounting plate with 2-1/8" (54mm) screws*2 and 1-1/4" (32mm) screw*1 Note: Screw (E) is an optional screw. We recommend using screw (E) for the stability of the lockset.
P19. INSTALLATION INSTRUCTIONS: REMOVE THE DECORATIVE COVER 1. Hold on the lip of the decorative cover 2. Put the thumbs on the thumbturn 3. Remove the decorative cover by pushing the thumbturn.
P20. INSTALLATION INSTRUCTIONS: CONNECTING THE CABLE Cable Connect the cable into the connector port. Connector port The metal connector side should face outside. Note: The red portion of the cable is aligned with the red portion of the connector port.
P21. INSTALLATION INSTRUCTIONS The cable must be arranged as shown in the diagram.
P22. INSTALLATION INSTRUCTIONS: INSTALL THE INTERIOR ASSEMBLY Tighten three screws as Insert 5/16" (7.8mm) screws "H" shown below and tighten Insert 13/16" (20mm) screw "I" and tighten.
P23. INSTALLATION INSTRUCTIONS: AUTOMATIC - BOLT DIRECTION DETERMINATION Steps: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press press button. Enter [00] and button. The Red LED will light up for 10 seconds. The lockset will have the bolt direction set. Note: We recommend to do bolt direction determination first once the lockset is installed on the door.
P24. INSTALLATION INSTRUCTIONS: RE-INSTALL THE DECORATIVE COVER We recommend re-installing the decorative cover after completing setup mode in page 18 to page 30. If you want to remove the decorative cover, Re-install the please hold the bottom of the decorative cover decorative cover and pull it toward yourself.
P25. SETUP MODE HOW TO CHANGE PROGRAMMING CODE Important: The pre-set programming code is 1-2-3-4-5-6. Please change the programming code before operating the lockset. Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter new programming code (six digits) and press button . Enter [10] and press .
P26. SETUP MODE HOW TO ADD AN USER CODE Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter new user code (four to six digits) and press button . Enter [20] and press . The Red LED will light up for 10 seconds. The lockset will have the new user code set.
P27. SETUP MODE HOW TO ADD A PROXIMITY CARD (only available for Proximity Card Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [20] and press . Put card to contact with the inductive zone. The Red LED will light up for 10 seconds. The lockset will have the new card set.
P28. SETUP MODE HOW TO ADD A REMOTE CONTROL (only available for Remote Control Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Press any button on the remote control and press button . Enter [20] and press . The Red LED will light up for 10 seconds. The lockset will have the new remote control set.
P29. SETUP MODE HOW TO ADD A SINGLE-USE USER CODE/ REMOTE CONTROL (single-use remote control only available for Remote Control Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button . 3. Please turn on auto-lock mode according to page 38 before following the below steps to enable single-use user code/ remote control.
P30. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING USER CODE Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or a current programming code) and then press button button 3. . Enter [30] and press . Enter existing user code (that you wish to delete) and press button . The Red LED will light up for 10 seconds. The lockset will delete the existing user code that you do not want.
P31. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING REMOTE CONTROL (only available for Remote Control Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button 3. . Enter [30] and press button . Press any button on the remote control (that you wish to delete) and press button . The Red LED will light up for 10 seconds.
P32. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING PROXIMITY CARD (only available for Proximity Card Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [30] and press . Put the card that you wish to delete to contact with the inductive zone. The Red LED will light up for 10 seconds.
P33. SETUP MODE HOW TO DELETE ALL EXISTING USER CODES AT ONCE Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [40] and press . The Red LED will light up for 10 seconds. The lockset will delete all existing user codes. Note: 1.
P34. SETUP MODE HOW TO DELETE ALL EXISTING PROXIMITY CARDS/ REMOTE CONTROLS AT ONCE (only available for Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [41] and press . The Red LED will light up for 10 seconds.
P35. SETUP MODE HOW TO DISABLE ALL EXISTING USER CODES (VACATION MODE) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [50] and press . Enter [0] and press button . The Red LED will light up for 10 seconds. The lockset will turn on vacation mode. 4. Enter [1] and press button . The Red LED will light up for 10 seconds.
P36. SETUP MODE HOW TO DISABLE BUTTON SOUND (MUTE MODE) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [60] and press again. Enter [0] and press button . The Red LED will light up for 10 seconds. The lockset will turn on mute mode. 4. Enter [1] and press button . The Red LED will light up for 10 seconds.
P37. SETUP MODE HOW TO SETUP AUTO-LOCK TIME DELAY Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [70] and press . Enter the seconds for delay time of auto-locking (10 to 90) and press button . The Red LED will light up for 10 seconds. The lockset will setup auto-lock time delay. Note: 1.
P38. SETUP MODE HOW TO ENABLE AUTO-LOCK MODE Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [80] and press . Enter [0] and press button . The Red LED will light up for 10 seconds. The lockset will turn on auto-lock mode. 4. Enter [1] and press button . The Red LED will light up for 10 seconds.
P39. SETUP MODE HOW TO ENABLE DOUBLE AUTHORIZATION MODE (only available for Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt) Steps as following: 1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button button 3. . Enter [99] and press . Enter [0] and press button . The Red LED will light up for 10 seconds.
P40. SETUP MODE HOW TO RESTORE FACTORY SETTING Steps as following: 1. Remove one battery from the battery pack. 2. Press [SET] button and put the battery back simultaneously. The Green LED will light up and beep twice. All functions will be restored back to factory setting. Note: 1. 2. 3. All existing user codes and current programming code will be deleted. Lock will be restored to pre-set programming code of 1-2-3-4-5-6.
P41. SETUP MODE HOW TO REPLACE BATTERIES OF REMOTE CONTROL Steps as following: 1. Loose two screws before opening the bottom shell. 2. Take the PCB out. 3. Push the battery out by inserting the tool into the crack between the PCB and the electrode terminal. 4. Push into the new battery. 5. Replace the PCB. 6. Place the bottom shell back and tighten the screws.
P42. OPERATION MODE HOW TO LOCK manually Keypad: Press button to lock the door. Remote control: Press lock button to lock the door as shown. (Only available for Remote Control Electronic Deadbolt) HOW TO LOCK automatically 1. Auto-lock mode should be turned on and auto-lock time delay should be also set up. 2. The lockset will be auto-locked in few seconds (default 10 seconds or the time you entered) after unlocking by using codes, card, or remote control.
P43. OPERATION MODE HOW TO UNLOCK 1. Enter a valid code, put card to contact with the inductive zone, or press unlock button on the remote control to unlock the lockset. 2. With double authorization mode is turned on, both user code and card, or both user code and remote control, must be authenticated to unlock the lockset. Note: 1.
P44. OPERATION MODE SAFE MODE 1. The keypad will be automatically deactivated for 1 minute after 4 wrong attempts. 2. Wrong attempts will not be counted when you press button to clear previous incorrect codes before the red LED lights up. 3. The deadbolt can be locked or unlocked by a valid traditional key under security.
P45. TROUBLESHOOTING GUIDELINE QUESTIONS ANSWERS The lockset did not operate correctly after 1. Check center of strike hole for alignment installation. with latch hole on the door to ensure free movement for the deadbolt. 2. Make sure the tailpiece is properly inserted (in the horizontal position) in the latch. 3. Do [AUTOMATIC -BOLT DIRECTION DETERMINATION]. Feel a bump while turning of the motor. 1. Please rotate the thumbturn back and forth a few times.
3. The new user code will not be accepted if 10 sets of user codes are already stored in the memory. The lockset is not able to unlock by the 1. Make sure you have entered the correct keypad user code. 2. Check to see if the Yellow LED light is flashing or not. It means "low battery" if the light keeps flashing. 3. Please make sure the position of strike plate is installed correctly if you see the latch is jammed. I am unable to reset the lockset. 1.
maybe not compatible with this lockset. Need more proximity cards. 1. Proximity card we offer is the latest Radio Frequency Identification (RFID) technology, compatible with standard Mifare -13.56 MHz. 2. You can use any card compatible with standard Mifare -13.56 MHz or purchase new cards from an authorized retailer. What should I do if the lockset cannot be 1. unlocked by using card? Make sure this card is stored in the lockset. 2. Please press button first then use card to unlock. 3.
P49. DECLARATIONS AND SAFETY STATEMENTS Federal Communications Commission Statement This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
P50.