User's Manual

ManualsBrandsTaiwan Carol Electronics ManualsAudio EquipmentDIGITAL WIRELESS MICROPHONE

DWR-882 Digital Wireless Microphone Manual

Thank you very much for selecting DWR-882 Digital Wireless Microphone. It is

recommended to read this manual carefully before using to make optimum use of your

equipment.

DWR-882 Digital Wireless microphone, based on the concept of designing for modern

lifestyle, with graceful curve, fine texture and user friendly design, is suitable for all kinds of

indoor activities, such as family, karaoke, school, company, organization and so on.

I. Product Contents:

1. One DWR-882 Digital Wireless Receiver

2. Two DWM-880 Digital Wireless Handle Microphones

3. One DC 7.5V Power adapter

4. One

φ6.3 M-XLR/M-XLR Cable

5. One User’s Manual

II. Parts Identification:

OUT PUT RESETRESET

figure 1

1. DWR-882 Digital Wireless Receiver (as shown in figure 1)

(1) POWER SWITCH: Switches on/off the Receiver (with status LED).

(2) MIC 1 CONNECTING LED: Lights up when microphone 1 is connected.

(3) MIC 2 CONNECTING LED: Lights up when microphone 2 is connected.

(4) VOLUME CONTROLLER 1: Controls the output volume of microphone 1.

(5) VOLUME CONTROLLER 2: Controls the output volume of microphone 2.

(6) ANTENNA: Receives signals from the microphone. The angle of the antennas can

be adjusted leftward, rightward or backward manually.

Summary of content (6 pages)

PAGE 1
DWR-882 Digital Wireless Microphone Manual Thank you very much for selecting DWR-882 Digital Wireless Microphone. It is recommended to read this manual carefully before using to make optimum use of your equipment. DWR-882 Digital Wireless microphone, based on the concept of designing for modern lifestyle, with graceful curve, fine texture and user friendly design, is suitable for all kinds of indoor activities, such as family, karaoke, school, company, organization and so on. I. Product Contents: 1.
PAGE 2
(7) RESET BUTTON 1: Resets microphone 1 (FOR TECHNICIANS USE ONLY). (8) φ6.3 FEMALE JACK: Connects to the output of amplifier. (9) RESET BUTTON 2: Resets microphone 2 (FOR TECHNICIANS USE ONLY). (10) DC POWER RECEPTACLE: Connects DC adapter, and the polarity of central pole is positive. UM-3 UM-3 figure 2 2. DWM-880 Digital Wireless Handle Microphone (as shown in figure 2) (1) BALL GRILLE: Protects the capsule, and the enclosed windscreen effectively reduces pop noises.
PAGE 3
plug the DC adapter to a wall outlet. (2) Press the Receiver’s power switch to turn the power on, and the status LED will light up green. (3) Press the microphone’s power switch to turn the power on, and the status LED will light up green. When the microphone connecting LED on the Receiver lights up red, it indicates the microphone signal is been received by the Receiver. (4) If the feedback noise appears when the volume is too high or the microphone is too close to the speaker, turn the volume down.
PAGE 4
3 4 figure 5 4. Change the Digital Wireless Microphone Channel When using wireless microphone, there might be interferences from the signals transmitted by another wireless microphone or other 2.4G wireless appliances near by. These disturbances can be solved by selecting a different channel. When selecting the channel, aim the arrow at the Fit the slotted screwdriver into this slot. scale or in between two scales. figure 6 (1) When changing the channel, it is not necessary to turn the power off.
PAGE 5
(3) The transmitting range is 20 meters, so keep the microphone within the effective range, or the output audio might be inconsistent. V. Specification: 1. Digital Wireless Receiver Model : DWR-882 Power Consumption Receiving Sensitivity : 1.5W : -78dBm Volume Adjusting Range : 0dB~12dB Output Jack Output Lever Dimension : φ6.3 Stereo Female Jack : 100mV : 284(L) × 157(W) × 211(H) mm Weight : 1.5Kg 2. Digital Wireless Handle Microphone Model : DWM-880 Carrier Frequency : 2.404～2.
PAGE 6
battery energy is running low, so please replace the batteries. VII. Caution 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not co-located or operating to conjunction with any other antenna or transmitter. 3. This device complies with Part 15 of the FCC Rules.