User manual GSM anti-theft alarm controller Scan QR code here download and install APP Android App Store 99+8 DEFENSE ZONES
GSM anti-theft alarm controller
GSM anti-theft alarm controller GSM anti-theft alarm controller Contents Preface.......................................................................................................... 3 24. Host Logs Deleting ....................................................... ........................... 21 Function Introduction.................................................................................... 4 25. SMS Notification of Arm/Disarm..............................................................
GSM anti-theft alarm controller GSM anti-theft alarm controller Preface Function Introduction Thank you for choosing the wireless alarm system product of our company. Apply advanced mobile communication technology, support SMS and dialing alarm, etc. Wireless alarm system adopts the most advanced digital sensing and controlling 8 wired defense zones and 99 wireless defense zones.
GSM anti-theft alarm controller GSM anti-theft alarm controller Alarm Host Installation wire connecting terminal: ZONE 8 Z8 GND GND ZONE 7 Z7 GND GND ZONE 6 Z6 ZONE 5 Z5 ZONE 4 Z4 GND GND ZONE 3 Z3 GND GND ZONE 2 Panel schemes: Z2 avoid steel-reinforced concrete and fire-proof doors. ZONE 1 receiving effect from all wireless detectors.
GSM anti-theft alarm controller GSM anti-theft alarm controller Installation and Use of Infrared Detector Please tear off the plastic insulating tape before use. Installation height is about 2.2 meters Installation and Use of Magnetic Door Sensor Door sensor is installed on the door. First clean a right place of the door, take out the sensor from the ground, should be installed in a corner indoors to obtain the ideal detection range, at and then stick a double-sided adhesive at the bottom.
GSM anti-theft alarm controller Function Setting 1.Initialization GSM anti-theft alarm controller Operating method: [21] [#] LCD display: Please insert SIM card and power on the system by adapter, built-in speaker would make a sound, and all icons display on the LCD, the time shows normally after all LED indicators are ON. Signal mark with 5 grids on screen in 10 seconds means host starts up normally with strong GSM signals.
GSM anti-theft alarm controller Operating method: [23] [XX] [#] XX Indicates:02~99 defense zones number GSM anti-theft alarm controller Operating method: [25] [#] LCD display: Example: Code defense zone 02 Operating method: [23] [02] [#] LCD display: 7 . Single Wireless Detector Deleting Setting In setup state, enter number [24] and then press the [02~99] defense zone number which needs to be deleted, finally press [#] to confirm.
GSM anti-theft alarm controller Operating method: [26] LCD display: GSM anti-theft alarm controller [02] [1] [#] 10 . Wireless Siren Coding Setting In setup state, input [28]+8-digit wireless siren coding, then enter [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Note: Wireless equipment coding includes sc2262 coding four data bits & 8 address bits.
GSM anti-theft alarm controller 12.Siren Ring Time Setting In setup state, enter [32], then input time [00~15] minutes, finally press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”. Default: 3 minutes Operating method: [32] [XX] [#] XX indicates: siren ring time, unit: minute Example: Set 2 minutes of siren ring time Operating method: [32] [02] [#] LCD display: GSM anti-theft alarm controller 14.
GSM anti-theft alarm controller GSM anti-theft alarm controller 16.Remote Call Ringing Times Setting In setup state, enter [36], then input ringing times [0~9], finally press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”.
GSM anti-theft alarm controller GSM anti-theft alarm controller 19.Host Keypad Lock Setting In setup state, enter [40], then input [0/1], finally press [#] to confirm. The host makes a “tick” 21. Host Timing Arm /Disarm Setting In setup state, enter [42], and then input disarming time [AABB], and then input arming time sound, and then a voice prompts “setting completed”. [XXYY], finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts Operating: [40] “setting completed”.
GSM anti-theft alarm controller GSM anti-theft alarm controller 23. Host Logs Inquires LCD display: In setup state, first enter [44], then press [#] to confirm; The host will make a “tick” sound and then enter into records list. Press “2” to page up and press “8” to page down. There are 10pcs of alarm logs in total. Operating: [44] [#] LCD display: 26. System Clock Setting In setup state, use keypad to input [48], then input the last 2 digits [YY] of the present year, 24.
GSM anti-theft alarm controller GSM anti-theft alarm controller LCD display: 27.SMS Phone Number Setting In setup state, enter [49~50], then input phone number, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.
GSM anti-theft alarm controller GSM anti-theft alarm controller Example: deleting the first group alarm phone number Operating: [51] [#] 32. Host GSM Signal Checking In setup state, enter [62] and then press [#] to confirm. The host makes a “tick” sound, and LCD display: then a voice prompts “setting completed”. GSM signal value is displayed. Operating: [62] [#] LCD display: 31.
GSM anti-theft alarm controller GSM anti-theft alarm controller 34.Sound Volume Setting In setup status, enter [64],then input volume level [0~9],press [#]to confirm. Once the host makes a “tick” sound, you will hear a voice prompt“setting completed”.Default level “6”. Operating method: [64] [X] [#] Mobile APP Operation The system can be controlled by APP. iOS mobile will map to SMS interface, Android mobile won’t map to SMS interface, but will finish the SMS operation in background.
GSM anti-theft alarm controller GSM anti-theft alarm controller App Use In the state of factory defaults, user can control the panel remotely on the SMS interface of the APP from any mobile phone. The panel only receive the APP command from the pr-set numbers which have been stored in it. (1)Add host account (3)Delete Account iOS mobile: Press [Edit], then press [Delete], the added host account will be deleted.
GSM anti-theft alarm controller GSM anti-theft alarm controller Daily Operation Operating: press [Out Arm The Host Operating: [Out Arm Remote controller is one kind of device which carries out mufti-function operation by radio. Its function is convenient for user to control its state when he is at the door (outdoor) or longdistance, such as Out Arm, Stay Arm , Emergency Alarm , Disarm functions etc. ] of remote controller.
GSM anti-theft alarm controller GSM anti-theft alarm controller 3 . Disarm 5 . Remote Control by SMS Disarm means to make the alarming host into non-alert state. One is, to Disarm the host from Arm state; the other is, to stop the alarm when the host is making alarms. After disarming, even if you trigger the detector, the host would not sound alarm (excluding 24- hour defense areas). If keypad lock is closed, press [ [ ]keypad directly to disarm.
GSM anti-theft alarm controller Maintenance 1.System detection GSM anti-theft alarm controller Technical Parameters 1、2 Appendix 1 Although the alarm system is used every day, it still needs regular care and maintenance and detection to ensure that the alarm system will be stable, reliable and safe. Normally the host needs a thorough inspection every 3 months and the detectors need to be checked once a month, at least once every 3 months in case of bad conditions. 2.
Wireless intelligent security alarm system GSM anti-theft alarm controller Technical Parameters 3 Appendix 3 :Administrator password system setup command table No Setting item Address Data(XY) Remark Appendix 3 :Administrator password system setup command table Factor y Default Coding of Remote Controller Setting Address Data(XY) Remark Factor y Default ON OFF Coding of Wireless Detector Setting 99 Single Wireless Detector Deleting Setting 99 Host Timing Arm / Disarm Setting All Wireless
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.