Thumb Controller User Manual V1.0 2015.
Disclaimers and Warnings Congratulations on purchasing your new DJI product. Carefully read the manual and all disclaimers before using this product. By using this product, you hereby agree to this disclaimer and signify that you have read it in its entirety. You agree that you are responsible for your own conduct, for all content that is created using this product, and for any consequences that may arise from either.
Content Disclaimers and Warnings In the Box Introduction Thumb Controller External Receiver (For Ronin Only) Installation Installing the Thumb Controller Installing the External Receiver (For Ronin Only) Connecting the Thumb Controller to the Gimbal Connecting the Thumb Controller to the Ronin-M Connecting the Thumb Controller to the Ronin Indicator Status Using the Thumb Controller Mode Function Gimbal Settings Device Settings DJI Assistant App Tuning DJI PC/MAC Assistant Tuning Settings Updating the Thumb
In the Box Check to ensure that all of the following items are included in the package. If any items are missing, contact DJI or your local dealer. The following items are included with the Thumb Controller for the Ronin-M: Thumb Controller×1 Quick Release Accessory Mount×1 USB Cable×1 Rubber Ring×1 The following items are included with the Thumb Controller for the Ronin: Thumb Controller×1 Receiver×1 4 Quick Release Accessory Mount ×1 4-Pin Cable×1 © 2015 DJI. All Rights Reserved.
Introduction The Thumb Controller is designed specifically for DJI Ronin series handheld gimbals. It provides a simple, intuitive interface for controlling the gimbal’s pan, tilt, and roll motion. The pressuresensitive stick and the easy-to-read OLED display give Ronin users more control than ever before. The Thumb Controller communicates with the Ronin-M via a preinstalled internal receiver. An external receiver is needed when the Thumb Controller is used with the Ronin.
[5] Micro-USB Port For charging the Thumb Controller and upgrading its firmware [5] [6] Override Button Allow the Thumb Controller to reactivated and updated following a failure update process [6] External Receiver (For Ronin Only) [1] [3] [2] [1] CAN Port Connects the receiver to the Ronin [2] Bind Button Connects the Thumb Controller to the Ronin [3] LED Indicator Indicates the status of the receiver [4] 6 © 2015 DJI. All Rights Reserved.
Installation Installing the Thumb Controller 1. Install the quick-release accessory mount by clamping it around the handlebar of the Ronin and tightening the screw. Remember to place the rubber ring on the on the handlebar and clamp the accessory mount around it when installing the unit on the Ronin-M. 2. Insert the Thumb Controller into the quick-release accessory mount and ensure that it is secure. © 2015 DJI. All Rights Reserved.
Installing the External Receiver (For Ronin Only) 1. Use the 4-pin cable to connect the CAN port on the Ronin to the CAN 1 or Can 2 port on the receiver. 2. Use the adhesive tape to secure the receiver on the Ronin. 8 © 2015 DJI. All Rights Reserved.
Connecting the Thumb Controller to the Gimbal Connecting the Thumb Controller to the Ronin-M 1. Turn on the Ronin-M. 2. Press the Ronin-M’s Bind Button (shown below) one time. The LED indicator on the Ronin-M will rapidly blink green. 3. Turn on the Thumb Controller. If the LED indicator on the Ronin-M and the LED indicator on the Thumb Controller both glow solid green, they have been successfully connected. Bind Button Connecting the Thumb Controller to the Ronin 1. Turn on the Ronin. 2.
Bind Button The binding process only needs to be completed one time, unless the bind button is pressed or the Ronin/Ronin-M needs to be connected to another Thumb Controller. 10 © 2015 DJI. All Rights Reserved.
Indicator Status Thumb Controller LED Indicator Status — Solid Red Blinking Red — Solid Green Description The Thumb Controller is being updated The Thumb Controller is not connected to the receiver The Thumb Controller is connected to the receiver Blinking Green The update process is complete — Solid Yellow External Receiver LED Indicator Status — Solid Red Blinking Red — Solid Green Blinking Green The Thumb Controller is fully charged Description The receiver is being updated The Thumb Controller
Using the Thumb Controller To enter the Main Menu, press and hold the center of the pressuresensitive stick. Mode Function ST Off ST On Auto Center Fast Normal Slow Up/Down Channel Left/Right Gimbal Setting Up/Down Direction Left/Right Menu Calibration Sensitivity Device Setting Sleep Power off 12 Default Setting Restore About Version ** © 2015 DJI. All Rights Reserved.
The Main Menu contains six tabs: Mode, Function, Gimbal Setting, Device Setting, Default Setting, and About. Press up/down on the pressure-sensitive stick to select an item. Press right to view and select options and press left to return to the Main Menu. RF NC DJI Ronin Thumb Controller Menu Mode ST Off SmoothTrack is off. The Thumb Controller is free to control the pan axis. The gimbal will stop and hold the last position determined by the pan axis control stick, without applying SmoothTrack.
Function The Function tab allows you to select the SmoothTrack speed. There are 3 possible speeds: Fast, Normal, and Slow. The value of each speed can be adjusted in the DJI Assistant app or the PC/ MAC Assistant. Gimbal Settings Channel Allows you to assign control of the pan, tilt, or roll motion of the gimbal to the up/down input on the pressure-sensitive stick. Allows you to assign control of the pan, tilt, or roll motion of the gimbal to the left/right input on the pressure-sensitive stick.
When the “Reverse” orientation is selected, the up/down and left/ right controls are switched. Calibration “Cali System” should be used if there is perceptible drift on any axis. The calibration procedure should take approximately 90 seconds to complete. Selecting “Auto Tune” will automatically adjustment each motor’s stiffness settings to achieve an optimal balance. This process should take approximately 20 seconds to complete.
DJI Assistant App Tuning You can adjust various parameters in the DJI Assistant app. Turn on the Thumb Controller and the gimbal, then launch the DJI Assistant app. You can adjust the control speeds in the Wizard menu. To meet your specific requirements, you can also access advanced functions through the Assistant app. In the Control Menu, you can adjust the Deadband, Maximum Speed, Smoothing, and Controller Priority.
DJI PC/MAC Assistant Tuning The DJI PC/MAC Assistant allows you to tune the Thumb Controller and update its firmware. The tuning procedures offered through the DJI Assistant App are the same as those offered through the DJI PC/MAC Assistant. There is no need to adjust the settings in both. The DJI Assistant app and the PC/MAC Assistant program cannot be connected to the Thumb Controller at the same time.
Updating the Thumb Controller and the Receiver You can find the latest firmware version information on this page and update the firmware by following the steps below: 1. Use the Micro-USB cable to connect the Thumb Controller to your computer, then wait until the indicator in the Assistant blinks blue. 2. Click “Update.” 3. Wait for the download to finish. 4. Click “Update” again and then click “Confirm.” 5. After the update is complete, turn the Thumb Controller off and then on again. 6.
Ensure that your computer is connected to the internet Close all antivirus programs and network firewalls Ensure that the device is turned on before beginning the update process Do not disconnect the USB cable until the update is complete If the Thumb Controller fails to update, follow the steps below: 1. Press and hold the override button. 2. Use the USB cable to connect the Thumb Controller to the computer. 3. Now, release the override button and wait for the connection to be established. 4.
Specifications Type RONIN TC Support Device Ronin, Ronin-M Operating Frequency 2.415GHz-2.454GHz Working Current <100mA @ 3.3V Communication Distance 60m Battery Life 18h Standby Life 20h Operating Temperature -20°~ 55° -20℃~50℃ Battery Type LiPo Battery Voltage 3.7V Battery Capacity 1150mAh Charge Time 2h Weight 50g Size 2.7×1.4×0.9 in. (68×36×23 mm) Mounting Bracket Diameter 1.0 in. or 1.2 in. (25 mm or 30 mm) Display White OLED, 0.96 inch, Dots: 128×64 20 © 2015 DJI.
The content is subject to change. Download the latest version from http://www.dji.com/product/ If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. © 2015 DJI. All Rights Reserved.
Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. The product is power by PC. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Hereby, SZ DJI TECHNOLOGY CO., LTD declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
