User's Manual

ManualsBrandsSZ DJI TECHNOLOGY ManualsElectronicsRONIN RX

Mode

ST Off

SmoothTrack is off. The Thumb Controller is free to control the pan

axis. The gimbal will stop and hold the last position determined by

the pan axis control stick, without applying SmoothTrack.

ST On

SmoothTrack is on. The Thumb Controller is free to control the pan

axis. The gimbal will stop and hold the last position determined by

the pan axis control stick, while applying SmoothTrack.

Auto Center

SmoothTrack is on. The gimbal will apply SmoothTrack when

reorienting and resetting the pan angle to the forward-facing

direction after the pan axis control stick is released.

RF NC

DJI Ronin

Thumb Controller

The Main Menu contains six tabs: Mode, Function, Gimbal Setting,

Device Setting, Default Setting, and About.

Press up/down on the pressure-sensitive stick to select an item. Press

right to view and select options and press left to return to the Main Menu.

Summary of content (12 pages)

PAGE 1
The Main Menu contains six tabs: Mode, Function, Gimbal Setting, Device Setting, Default Setting, and About. Press up/down on the pressure-sensitive stick to select an item. Press right to view and select options and press left to return to the Main Menu. RF NC DJI Ronin Thumb Controller Menu Mode ST Off SmoothTrack is off. The Thumb Controller is free to control the pan axis. The gimbal will stop and hold the last position determined by the pan axis control stick, without applying SmoothTrack.
PAGE 2
Function The Function tab allows you to select the SmoothTrack speed. There are 3 possible speeds: Fast, Normal, and Slow. The value of each speed can be adjusted in the DJI Assistant app or the PC/ MAC Assistant. Gimbal Settings Channel Allows you to assign control of the pan, tilt, or roll motion of the gimbal to the up/down input on the pressure-sensitive stick. Allows you to assign control of the pan, tilt, or roll motion of the gimbal to the left/right input on the pressure-sensitive stick.
PAGE 3
When the “Reverse” orientation is selected, the up/down and left/ right controls are switched. Calibration “Cali System” should be used if there is perceptible drift on any axis. The calibration procedure should take approximately 90 seconds to complete. Selecting “Auto Tune” will automatically adjustment each motor’s stiffness settings to achieve an optimal balance. This process should take approximately 20 seconds to complete.
PAGE 4
DJI Assistant App Tuning You can adjust various parameters in the DJI Assistant app. Turn on the Thumb Controller and the gimbal, then launch the DJI Assistant app. You can adjust the control speeds in the Wizard menu. To meet your specific requirements, you can also access advanced functions through the Assistant app. In the Control Menu, you can adjust the Deadband, Maximum Speed, Smoothing, and Controller Priority.
PAGE 5
DJI PC/MAC Assistant Tuning The DJI PC/MAC Assistant allows you to tune the Thumb Controller and update its firmware. The tuning procedures offered through the DJI Assistant App are the same as those offered through the DJI PC/MAC Assistant. There is no need to adjust the settings in both. The DJI Assistant app and the PC/MAC Assistant program cannot be connected to the Thumb Controller at the same time.
PAGE 6
Updating the Thumb Controller and the Receiver You can find the latest firmware version information on this page and update the firmware by following the steps below: 1. Use the Micro-USB cable to connect the Thumb Controller to your computer, then wait until the indicator in the Assistant blinks blue. 2. Click “Update.” 3. Wait for the download to finish. 4. Click “Update” again and then click “Confirm.” 5. After the update is complete, turn the Thumb Controller off and then on again. 6.
PAGE 7
Ensure that your computer is connected to the internet Close all antivirus programs and network firewalls Ensure that the device is turned on before beginning the update process Do not disconnect the USB cable until the update is complete If the Thumb Controller fails to update, follow the steps below: 1. Press and hold the override button. 2. Use the USB cable to connect the Thumb Controller to the computer. 3. Now, release the override button and wait for the connection to be established. 4.
PAGE 8
Specifications Type RONIN TC Support Device Ronin, Ronin-M Operating Frequency 2.415GHz-2.454GHz Working Current <100mA @ 3.3V Communication Distance 60m Battery Life 18h Standby Life 20h Operating Temperature -20°~ 55° -20℃~50℃ Battery Type LiPo Battery Voltage 3.7V Battery Capacity 1150mAh Charge Time 2h Weight 50g Size 2.7×1.4×0.9 in. (68×36×23 mm) Mounting Bracket Diameter 1.0 in. or 1.2 in. (25 mm or 30 mm) Display White OLED, 0.96 inch, Dots: 128×64 20 © 2015 DJI.
PAGE 9
PAGE 10
The content is subject to change. Download the latest version from http://www.dji.com/product/ If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. © 2015 DJI. All Rights Reserved.
PAGE 11
Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Hereby, SZ DJI TECHNOLOGY CO., LTD declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
PAGE 12
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences, et (2) c et appar eil doi t ac cepter t oute i nterférence, y c ompris c elles pouv ant causer un mauvais fonctionnement de l'appareil. RONIN RX could be powered DC 12V-16V (powered by RONIN through CAN port with a 4-Pin Cable)or DC 5V (powered by PC through USB port) RONIN is powered by intelligent battery, the battery capacity is 3400mAh, voltage is 14.