DJI SRW-60G User Manual 2016.06 V1.
Disclaimer and Warning Congratulations on purchasing your new DJITM product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, or damage to your DJI product or damage to other objects in the vicinity.
Before You Begin Make sure all the parts listed in the In the Box section below are included in the package. Read this entire User Manual and watch the informational and tutorial videos on the product page of DJI’s official website (http://www.dji.com). Read the disclaimers and warnings above to understand your legal rights and responsibilities. If you have any questions or problems during the installation, maintenance or use of this product, please contact DJI or a DJI authorized dealer.
SRW-60G Diagram Transmitter 1. HDMI Port For connecting to the HDMI output for HDMI transmission. 2. Gimbal Mounting Adapter For mounting to a Ronin-MX or Ronin-M. The adapter can be removed when not used with the Ronin-MX or Ronin-M. 3. Cable Slot For fastening the cable in position. 7 6 5 4 1 3 2 4. Link Button For linking to the Receiver. 6. Power Port For power supply. 5. Micro USB Port For firmware upgrades and power supply. 7. Status LED Indicates the communication status with the Receiver.
Usage Using the SRW-60G with a Ronin Series Gimbal 1. Loosen the screw of the clamp on the gimbal mounting adapter of the Transmitter. Then attach the Transmitter to the arm of the Ronin-MX or Ronin-M and tighten the screw. 2. Link the HDMI Ports of the Transmitter and the camera by using a soft and flexible HDMI cable (not provided). 3. Connect the Power Port on the Transmitter to the CAN1 Port (or the USB port) of the Ronin-MX by using the provided transmitter power cable.
4. If using a Ronin, remove the gimbal mounting adapter and stick the Transmitter onto the Ronin or your camera. Antenna Position 5. Remove the mounting adapter and mount the Receiver in place. Antenna Position NOTICE Ensure both the Transmitter and Receiver are not obstructed during use. Using the SRW-60G in a Meeting Room or at Home 1. Remove the mounting adapters. 2. Connect the HDMI output and input to the Transmitter and Receiver separately. 3.
Linking The Transmitter is linked to the Receiver before delivery. Linking is only required when using a new Transmitter or Receiver. Ensure the Transmitter and Receiver are properly connected to the HDMI device before linking to avoid failure. How to link Press the Link button on the Transmitter once. The linking process will complete in approximately 10 seconds. Status LED Descriptions Transmitter Status LED Receiver Status LED ...... Blinks red ...... Blinks green slowly slowly Blinks red ...... ......
Specifications General Max Transmission Distance 10 m (unobstructed) Max Transmitter Power (EIRP) Transmitter: 17 dBm, Receiver: 30 dBm Receiver Sensitivity -72 dBm Operating Frequency 57 GHz to 64 GHz Video Output Port HDMI Video Resolution From 480 i / 576 i to 1080p 60Hz Latency < 1 ms Transmitter Dimensions 78 mm (L) × 33 mm (W) × 16 mm (H) Weight 46 g Antenna Gain LRP Mode: 5 dBi; MRP Mode: 9 dBi Operating Voltage (DC) 7.4-12 V (CAN Port) or 5 V (USB Port) Max Consumption 1.
FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Radiation Exposure Statement: This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
DJI Support http://www.dji.com/support The content is subject to change. Download the latest version from http://www.dji.com/product/ronin-mx If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. RONINTM is a trademark of DJI. Copyright © 2016 DJI All Rights Reserved. Printed in China. © 2016 DJI All Rights Reserved.