Stepper User manual Please read this manual carefully before using this product and keep it properly
1、Directory Serial Content number 1 Directory 2 Instructions for safe use 3 Filed under box 4 Assembly instructions 5 Electrical control instructions 6 Maintenance guidelines 7 General fault and troubleshooting 8 Maintenance terms 9 Workout instructions 10 Warm body exercise You are welcome to choose the electric walker machine made in China. Our products will improve your health level. The more familiar with your walker machine, you will find it easy to use it.
II. Safe use instructions We consider many safety issues in design and manufacturing. To ensure your safety, be sure to read the entire manual before operating it, just in case.We do not bear any consequences arising from an abnormal operation. Dangerous . Do not use the heart rate device simultaneously with other wireless heart rate devices, otherwise it will cause electrical interference.
10, Please place the machine on clean and flat ground to keep the ventilation good, ensure there are no sharp items nearby and do not use it near the water and heat source. 11, Use the handrail when going up and down the machine. When the walker is not completely stopped, do not get off.If you need to jump away urgently, you must unout the safety lock: the walker will stop immediately. 12, Do not operate the trainer when using oxygen equipment or sprays near the machine.
Accessory details Serial Parts number Number A Safety lock One B 6mm inside the hexagon wrench One C Lubricant One D Round knob Two E Remote control One F Key box One G Cross recessed half round head tapping nail ST4.0*16 4、Assembly instructions Step 1: Lift the main frame out of the carton.
Step 2: Please hold the column with the figure by hand and slowly in the direction shown in the icon arrow, and use the D#(circular knob) to fix the column to the main frame.
Before using the walker: please plug in the power supply first, turn on the switch (switch in red), please wait for the screen to illuminate, and enter the start interface. Power switch 1. function instructions The appearance of the electronic balance sheet is shown in Fig 2. boot start Start normally after 3 seconds. 3. security lock function Pull out the security lock and immediately show that the "- - -" walking machine stops quickly, and issue a beep alarm sound.
4.1. Start / Stop key: Start key, in the walker stop state, press the stop key, the speed shows "0.5", and the walker starts.Stop key. In the running state of the walker, press the open and stop key to clear all data. After the walker will stop, return to manual mode and the walker will stop. 4.2. Speed add and minus key: It can be used to adjust the set value when setting the parameter.After the walker starts, it can be used to adjust the speed, step by 0.
value is 0.1MPH 7、Operation during the .motion: 7.1. Reduce the running speed. 7.2. Press increases the speed of the walker. 7.3. Press Step to slow down to stop. 7.4. Remote control battery installation instructions 7.4.1 below: rotate the battery cover for 90 ° counterclockwise and remove the battery cover. 7.4.
8. energy-saving mode: In standby mode, no operating machine enters the energy saving mode, when the display has no display, press either button to exit to standby mode. Scope of each display data: TIME:5:00 – 99.59(MIN) DISTANCE: 1.0 – 99.0(KM) CALORIES: 20.0 – 990 (C) SPEED:0.5-6.5(MPH) 9. others The standard value of calories is 30k cal / km. Acceleration is 0.1MPH, and deceleration is 0.1MPH.
4,To facilitate movement, the walker set installed wheels, please confirm that the power is disconnected and fold the body before moving. 5,Regularly check and lock all the parts of the walker; the parts of the damaged ring must be replaced immediately. 6,To better maintain and extend the life of the walker, it is recommended that you let the walker rest for 10 minutes after continuing for 30 minutes.
8,Lubricant The stepper is added with lubricating oil at the factory, but often checks the lubricity of the stropper, which helps the walker to keep in the optimal use condition.The walker must be lubricating after one year or for 100 hours. After 30 hours or 30 days, pull the starting belt on the side to touch the running surface inside, if feeling the lubricating oil; if there is a strong dry feeling when touching the surface, follow the following instructions.
It means that the controller did not E02 detect the voltage above the motor Check that the terminal connection of the motor line on the control is secure 1 Shutdown time into fault state, electronic meter buzzer sounds 9, display fault code, and other areas do not display content.Restboot restart after about 10 seconds into standby.
the system self-protection; adjust the stepping machine to start operation.Also check whether the motor has current or burnt odor, replace the motor, replace the controller, or check whether the power supply voltage specification is inconsistent or low, retest using the correct voltage specification. Inindicates that no safety lock --- signal was detected in the spreadsheet The magnetron is damaged, whether the magnetron is installed is correct and the magnet is placed. 2.
VIII. Maintenance terms 1,Warranty range Non-human damage under normal use and maintenance. 2. The following terms are not under the warranty a.Damage caused by abuse, negligent use, accident, or unauthorized modification; b.Damage caused by improperly adjusting the running belts and drive belts; c.Damage due to abnormal maintenance; d.Other violations and resulting damage. 5. The warranty commitment is only valid for family private use and is not applicable to professional training situations such as gyms.
1、Stretch down: Knees slightly curved, the body slowly bend forward, let the back and shoulders relax, hands try to contact the toes.Hold it for 10-15 seconds, and then relax.It was repeated three times 2、Foot tendon extension: Sit on a clean cushion, straighten one leg, and close the other inward, keep it close to the inside of one leg, and try to touch your toes with your hands.Hold it for 10-15 seconds, and then relax.
FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.