*** USER’S MANUAL *** FCC ID : RLS-STAVL0358
Federal Communications Commission (FCC) Warning THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERECE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
IntelliTrac® X Series Hardware Installation Guide 1. Install SIM Card To install the SIM card: - Press the yellow button to eject the SIM card holder. - Before insert the SIM card, make sure the PIN code has been disabled. - Insert the SIM card. - Check that it fit into place correctly.
2. Install GPS and GSM Antennas Connect GPS antenna to the GPS connector. The optimum location for the GPS antenna is on the roof of the vehicle. The covert and GPS antenna are directional, make sure they are facing up and laying as flat as possible. Secure them in place with glue, or zip ties. Note : Do not block or cover the GPS antenna with metal. Connect GSM antenna to the GSM connector. The GSM antenna is non-directional, so you can hide it in any place of vehicle. 3.
(1) General Installation (Without immobilizer installed) Connect Ground(-Black) and BAT(+Red) wires to the battery of vehicle. (2) With immobilizer installed Connect Ground (-Black) and BAT (+Red) to the battery of vehicle. Connect Ignition Key (Pink) to the IGNITION wire.
4. Install Immobilizer Relay (Optional) (1) If the wireless relay terminal is same as car original fuel pump (or ignition, or starter) relay terminal, please just unplug the car original relay, then plug in the wireless relay. (2) If the wireless relay terminal is different with car original fuel pump (or ignition, or starter) relay terminal : Please plug the wireless relay into the spare relay socket, then a. Connect the socket Black wire to Ground. b. Connect the socket Red wire to IGNITION c.
5. Install Input Cable 1 3 1 3 5 7 9 11 1 3 5 7 9 2 4 2 4 6 8 10 12 2 4 6 8 10 Power Input Output Input Connector 1 : Input1 2 : Input2/ACC 3 : Input3 4 : Input4 5 : Input5 6 : Input6 7 : Input7 8 : Input8 9 : Analog Input1 10 : Analog Input2 11 : Vout +5V 12 : Ground The Input number 1, 2, 3, 4 are positive triggered inputs and Input number 5, 6, 7, 8 are negative triggered inputs. If you would like to use power saving function, please connect the Input2/ACC to ACC wire.
Positive Trigger: Negative Trigger: Copyright © 2003 Systems & Technology Corporation
6. Install Output Cable 1 3 1 3 5 7 9 11 1 3 5 7 9 2 4 2 4 6 8 10 12 2 4 6 8 10 Power Input Output Output Connector 1 : Output1 2 : Output2 3 : Output3 4 : Output4 5 : Output5 6 : Output6 7 : Output7 8 : Output7 (via relay) 9 : External Output Power 10 : Ground The output number 1, 2, 7 are positive triggered outputs and output number 3, 4, 5, 6 are negative triggered outputs.
7. LED Indicators Status Description There are 4 LEDs in front panel. When you power on the unit, these 4 LEDs will become blinking. After blinking several times, IntelliTrac X8 will start the modem which is inside the unit. In this time, the ERR led light is still bright. This is normal condition. Waiting for several seconds, the ERR led light will put out. Then you can start to manipulate the IntelliTrac X8.
90 ms On / 3 secs Off Logged to network. No call in progress.
8. Unit Configuration Connect the download cable between IntelliTrac unit and PC serial interface and use IntelliTrac InstallWizard program to configure a new IntelliTrac unit. Please refer to the InstallWizard User Manual for more detail information.