SE0510 SE0550 E50/E50w Installation Guide Built-in Bluetooth® Hi-Fi amplifier / touch panel
Important Safety Instructions CAUTION: To reduce the risk of electric shock, do not remove the cover. No user-serviceable parts inside. Refer to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Pack Contents E50/E50w touch panel x 1 Mounting frame x 1 47mm deep double gang Pre-fitted with IMO plugs for speaker cables M3 x 7mm screw x 1 Dry lining back box x 1 M3.5 x 30mm screws x 2 Dust cap x 1 Fits into front jack socket Power supply x 1 Speaker cables x 2 Power extension cable x 1 UK / EU / AUS / NZ 7m length 5m length Q Acoustics Qi 65CB in-ceiling speakers x 2 3.
Introduction Systemline E50 is an installed Bluetooth Hi-Fi system that is easy to fit into your room. It is particularly suited to kitchens or bedrooms but could equally be used in any other room in the house including bathrooms*. The following instructions assume that you are competent in general electrical installation skills. You will need to mount a touch panel into a double gang back box and route cables from this box to the speakers and mains.
E50 System Schematic The system is designed to be connected together as shown below: LINE IN DC IN SPEAKERS -L+ -R+ 6
Planning E50 Positioning and Back Box Locations Use the guidelines below to plan the positioning of the back boxes, speakers and cabling. Dimensions should be checked prior to installation to ensure the layout works correctly with the supplied lengths of cable.
First Fix Wiring Cut holes for required back boxes and speakers. Run speaker cables and power cable as shown, leaving the tails accessible for second fix. Optional line-in cable may be run at this point. Notes 1. Switched mains socket required next to cable break-out box. 2. Single gang back-box required next to TV aerial point for optional TV sound / AUX input.
Second Fix Connect cable tails to touch panel, speakers and PSU. Fix items in place, using the instructions supplied with the speakers to ensure correct speaker installation. Notes 1. Blanking plate required to cover break-out box - requires a single hole to exit DC cable. 2. Optional TV sound / Aux input requires a 25 x 50mm twin phono Euro module e.g. Philex EMSPK2W or similar.
Appendix 1: E50w Bathroom Installation Guide E50w is designed to be fitted into a bathroom environment, which is clearly different to most other rooms in the home. The nature of this wet environment is recognised by the respective standards authorities, who test products in terms of their suitability to be installed in such areas. E50w complies with IP54, subject to the following conditions: 1.
3. Installation Step 1 Step 2 Apply silicone sealant on the back of the frame. Fit the frame onto the back box and secure using 2 screws. Step 3 Step 4 Plug cables into keypad and fit into the frame. Secure the front using the screw provided and smooth out the edges using a sealant smoother. All other instructions for the connection and fitting of E50w apply, except in this instance the left & right speaker wires are connected to a single stereo Q Install speaker (Qi-65 CW-ST).
Stortford Hall Industrial Park Dunmow Road Bishops Stortford Hertfordshire CM23 5GZ United Kingdom www.systemline.co.uk ©2018 Armour Home Electronics, all rights reserved. Our policy is one of continuous improvement and we reserve the right to change the designs and specifications without notice. All information is given in good faith. The manufacturer accepts no responsibility for errors, omissions or incorrect assumptions. Designed and engineered in the United Kingdom. Made in China (P.R.C.
