Geniox Core Control system 43.04.02 230V

ManualsBrandsSystemair ManualsAir Handling UnitsGeniox Core

Table Of Contents

Geniox

Access CU27 Controller

Frontpage

Project:

Date:

Geniox-Core CS 43.04.02 230V GB

07-08-2020

Rev.:

initials:

MIKE

43.04.02

Sheet:

Next sheet:Total sheets:

Manufacturer:

Systemair A/S, Denmark

Project cover sheet: page 1

Geniox Core Control system 43.04.02 (230V)

Documents listed on pages below:

AHU unit data.

Total consumed power:

Ik max on fuse in unit:

Heat exchanger type:

Heat coil type:

Cooling coil type:

Electrical data:

Fan fuse size:

Supply air fan cable resistance:

Extract air fan cable resistance:

See data in the attached annex - Technial data

Quick Guide: page 2

Cable plan: page 100-116

6 kA

Max pre-fuse: Watch printed order

Watch printed order

External connections: page 10-17

Modbus address list: page 26

Circuit Diagram: page 19-26

General Description: page 3-4

Units with internal cabinet:

Modbus Guide: page 21

Ved Milepælen 7

8361 Hasselager

Cabinet is always inside the unit.

Summary of content (37 pages)

PAGE 1
Geniox Core Control system 43.04.02 (230V) Documents listed on pages below: Project cover sheet: page 1 Quick Guide: page 2 General Description: page 3-4 External connections: page 10-17 Circuit Diagram: page 19-26 Modbus Guide: page 21 Modbus address list: page 26 Cable plan: page 100-116 Units with internal cabinet: Cabinet is always inside the unit. AHU unit data.
PAGE 2
Geniox Access CU27 Controller Quick guide Project: Date: 06-11-2019 Rev.: Sheet: 2 Geniox-Core CS 43.04.02 230V GB 43.04.
PAGE 3
RSA (D+) RSB (D-) GND Symbols are according to IEC 60617. On the following 2 pages there are descriptions of used symbols in the project.
PAGE 4
Labeling of wires are marked with terminal name Components are marked with component codes followed by a number according to IEC 61346-1 Chart 1 Components code -F9 Number BN BU Wire has colour blue -F 10 Wire has colour brown -T105 Geniox Access CU27 Controller General Description Wires Project: Date: 06-11-2019 Rev.: Sheet: 4 Geniox-Core CS 43.04.02 230V GB 43.04.
PAGE 5
0 1 2 3 4 5 6 7 8 9 A -SF2 Switch -SF3 Switch 1 -SF5 Switch -SF6 Switch ** 1 1 2 -W581 1 2 -W583 Ext. stop 2 -W584 1 2 -W580 B ** C -BP5 Extra filterguard Supply air ** C 3 B A 1 2 -W363 D D E F REF DI5 T28 REF DI4 T29 REF DI3 T30 REF DI2 T31 REF DI1 T32 DI1 DI2 DI3 DI4 DI5 -KF1 -KF1 -KF1 -KF1 -KF1 Reduced speed Normal speed ext. Ext. Stop / High speed/ Extra filter guard Cooling alarm Ext. Change over / HP defrost DI1:T32 20.2 DI2:T31 20.
PAGE 6
1 2 3 4 5 6 7 8 9 3 0 -X4 2 -X4 BN-W456 -BR2 Fire thermostat Extract air 17.3 DI9 0V 17.3 DI9 ** C BN-W359 1 BK -SF22 BU-W456 ** GY B ext. BU-W457 ** Fire Supply air 60 °C 16.3 DI7 0V 16.3 DI7 -BR1 Fire thermostat If there are no Fire thermostat or Smoke detector. a connektion between X4:1 and X4:3 is necessary.
PAGE 7
0 1 2 3 4 5 6 7 8 9 A A BK -R1 2,2K W B ** BK GY BK BN-W513 RD-W458 GY BK BN-W514 BR ** RD GY BK BN-W515/516 ANG 24V -BT8 Room 1 P Temp sensor ** GY BK BN-W517/W520 0-10V DPT G0 (0V) G (24V) -BM1/BM4 RH sensor P Extract/Room Out 1 (0-10V) DPT ANG 24V -BQ1/BQ2 CO2 sensor P Duct/Room 0-10V ** ANG 24V -BP4 Pressure transmitter P 0-10V -BQ3 Smoke det.
PAGE 8
0 1 2 3 4 5 6 7 8 9 -BT13 Pre-heat Frost Pt 1000 -BT7 Outdoor Temp. ** Pt1000 -BT10 Frost protection Pt 1000 Pt1000 -BT5 Supply air Duct sensor Pt1000 A Pt1000 A Pt 1000 B B WH BK -W357 WH BK -W367 -BT14 Pre-heat Temp. ** Pt 1000 BN BU -W507 Pt1000 BN BU -W355 C C WH BK -W369 D D AI U1 AIU2 24V 0V UI4 REF T84 24V 0V UI3 REF T83 24V 0V UI2 REF T82 24V 0V UI1 REF T81 AIU3 AIU4 E E -KF1 -KF1 -KF1 -KF1 Supply air Frost Pre-heat Frost. Outdoor Pre-heat Temp.
PAGE 9
0 1 A 2 3 4 5 6 7 8 9 A -KF1 -KF1 -KF1 -KF1 Start heating Pump 230V out Start cooling 1 Heat pump cooling Pre-heat / extr. Contr. Alarm / Fire damper / Run indication DO1:T61 20.6 DO2:T62 20.6 DO3:T63 20.6 DO5:T65 20.
PAGE 10
1 2 3 19.4 19.4 0 0VDC 24VDC A 4 5 6 7 8 9 A -KF1 -KF1 Damper Start Heat 1/Heat Pump Change over DO4:T64 20.6 DO6:T66 20.6 B B T64 Com Com DO6 DO 6 DO4 DO 4 T66 C 1 2 3 C -X5 BNBK GY -W530 D D =Damper +Splitter E E ** F -QM31.1S ** Damper Motor **option Damper Motor Supply air Damper Geniox Access CU27 Controller ** -QM71.1S -QM32.1 ** Damper Motor Supply air Damper 2 Damper Motor Damper Motor Extract air Damper -QM72.1 BNBU -W572.
PAGE 11
0 A 1 2 3 4 5 6 7 8 9 A -KF1 -KF1 Heater 1 Cooling / DX Circuit 1 Change over / HP AO1:T71 20.8 AO2:T72 20.8 B B T71 0V AO2 24V 0V AO 2 AO1 24V AO 1 T72 C 11.3 11.3 14.0 14.
PAGE 12
0 A 1 2 3 4 5 6 7 8 9 A -KF1 -KF1 Pre-heater Free AO3:T73 20.8 AO4:T74 20.8 B B T73 0V AO4 24V 0V AO 4 AO3 24V AO 3 T74 C 11.8 11.8 19.2 19.
PAGE 13
0 1 2 3 4 5 6 7 8 A L1 N PE A 9 -X1 -F1 1 3 ** -F3 1 3 BNBUPE -W1000 Main power supply 2 4 B 2 4 B C C 1 3 5 N -S10 PE 2 4 6 N Main Switch ** D D - Supply L1 - Supply N - Supply PE F +Supply air -GQ1 Control power BN BU +Extract air -W102 GNYE L N PE L 19.3 L1 230V 19.3 N 230V 19.
PAGE 14
F **option Geniox Access CU27 Controller Control power -EA1 ** -EA2 ** Project: Date: 06-11-2019 ** -EA3 ** RDBK -W703 RDBK -W702 -EA4 ** + + 20.2 20.2 7 -EA5 ** - -SF1 Light switch - + RDBK -W700 - Lamp Lamp 20.1 20.1 18.3 18.3 18.3 6 + 1 2 switch switch L1 230V N 230V PE 230V 5 - -24V 4 + B B C C L N PE 3 - V+ V- -T1 Power supply 24V DC - 14.6 A + DO3 (L) 2 Damper 15.2 0VDC Motor 15.2 24VDC 4 (L) 3 (N) PE 1 Capillar 11.2 0V Heat 11.2 24V Controller 20.
PAGE 15
0 -KF1 1 2 3 4 5 6 7 8 Systemair A/S Access CU27 Controller A B C D A DI1:T32 10.1 DI1 Reduced speed AI:T1 12.0 (0) Smoke detector AI DI2:T31 10.2 DI2 Normal speed ext. AI6:T14 12.2 0V Pressure supply AI DI3:T30 10.4 Ext. Stop / High speed/ DI3 Extra filter guard DI4:T29 10.6 DI4 Cooling alarm AI5:T15 12.4 0V Pressure extract AI4:T16 12.7 CO2 sensor/RH sensor/ 0V DI5:T28 10.8 DI5 Ext. Change over / HP defrost DI6:T27 11.1 DI6 Frost thermostat AO1:T71 Heater 1 AI DO1:T61 14.
PAGE 16
0 1 2 3 4 5 6 7 8 9 Access controller Int-link 1 Int-link 2 A A Splitter B DPT (8) X Exchanger DPT-Supply (5) Rotor control (7) ** B ** X By.pass damper Splitter (25) C ** (26) ** ** Sectional defrost controller (53) C ** Splitter EC fan (1) D EC fan (2) E F DPT Extract (6) D E F Modbus Address (x) **option Geniox Access CU27 Controller RS485 Modbus guide Project: Date: 06-11-2019 Rev.: Sheet: 21 Geniox-Core CS 43.04.02 230V GB 43.04.
PAGE 17
0 1 2 3 4 5 6 7 8 9 A A 20.3 20.3 20.2 20.2 0V link1 24V link1 B- link1 A+ link1 0V link1 24V link1 B- link1 A+ link1 1 B B C C D -BP1 Dual DPT IN1 IN2 T1+ T1- T2+ T2- Dual DPT E BP1:A+ BP1:ABP1:B+ BP1:B- Yellow SAF GNYE WH -W601 GQ1 BUS Grey SAF Red Filter Blue Filter E EC fan DI1 F -BT4 Eff. Temp -GQ1 EC fan Pt1000 -BT3 Extract Temp. Pt1000 BK WH BK WH -W444 -W343 Extract Temp. Effencicy Temp. 24V MODBUS ADDRESS 5 A (D+) B (D-) GND A B D WH-W661.
PAGE 18
0 1 2 3 4 5 6 A 7 8 9 A 24.9 24.9 24.9 24.9 0V link2 24V link2 B- link2 A+ link2 2 B GNYE BN B WH-W662.2 =BUS RS485 +Splitter C C D MODBUS ADDRESS 6 -BP2 Dual DPT IN1 IN2 T1+ T1- T2+ T2- Dual DPT WH -W341 BK Intake Temp. Yellow EAF GNYE WH -W602 GQ2 BUS Grey EAF Red Filter Blue Filter E BK WH -W442 Exhaust Temp./de-ice -GQ2 EC fan -BT2 Exhaust Temp. DI1 ** F Pt1000 -BT1 Intake Temp. EC fan Pt1000 ** F MODBUS ADDRESS 2 ** EBM connections for EC fan see page 3.
PAGE 19
0 A 1 20.4 20.4 20.4 20.3 2 3 4 5 6 7 8 0V link2 24V link2 B- link2 A+ link2 0V link2 24V link2 B- link2 A+ link2 2 GNYE BN B GNYE BN WH-W642.
PAGE 20
0 1 2 3 4 5 6 7 8 A 9 A Agnd B AI1 B 50 A 51 N 52 E 53 =Sec. defrost Box B MODBUS ADDRESS 53 Sectional defrost controller -KF5 D AO5 AO4 AO3 AO2 - - + + -X2 AO1 C G G0 C D E E 24.9 24.9 24.9 24.
PAGE 21
0 1 2 3 4 5 6 7 8 9 A A B B C C D D E E F F Geniox Access CU27 Controller Modbus address list Project: Date: 06-11-2019 Rev.: Sheet: 26 Geniox-Core CS 43.04.02 230V GB 43.04.
PAGE 22
Geniox Access CU27 Controller -W232, -W251, -W253, -W341 Rotor control RHC Project: Date: 06-08-2020 =A3+DVAF-SA-BT1 Pressure Guard -W341 3 2 -W253 3 2 -W251 17 A 18 B 19 GND Pressure Guard -BP53 -BP51 U V W PE L N PE Intake Temp. Pt1000 BK WH 1 2 1 2 BN BU PE mm² mm² mm² mm² mm² mm² mm² Black White mm² mm² Remark: Intake Temp.
PAGE 23
Geniox Access CU27 Controller -W351, -W353, -W355 -BT5 7 8 GO Y Electric pre-heater Project: Date: 06-08-2020 -W355 7 8 GO Y 1 2 -W353 Electric heater L1 L2 L3 N PE L1 L2 L3 N PE Supply air Duct sensor Pt1000 BN BU BK BN BU GY RD WH BK BN BN BU GY RD WH mm² mm² mm² mm² mm² mm² mm² -T61:N -T26:REF -T71:AO1 -T26:DI7 -T71:0V -T61:DO1 mm² mm² mm² mm² mm² mm² -T87 -X2:4 (L) -X2:3 (N) -T24:REF -T86 -T24:DI9 Brown Blue mm² mm² -T81:UI1 -T81:REF Remark: Temperatur sensor supply air Cable-
PAGE 24
Geniox Access CU27 Controller -W357, -W359, -W363, -W367 -BT13 1 -W367 3 Extra filterguard Supply air -BP5 -W363 White Red -W359 Capillar sensor -E1 Frost protection Pt 1000 Pt1000 Pre-heat Frost Pt 1000 Project: Date: 06-08-2020 Pt1000 Brown Gray BN GY BK WH -T82:REF -T82:UI2 mm² mm² mm² -T94 =A1-24V:+ =A1-24V:- Black White mm² mm² Remark: Pre-heat Frost Cable-type: mm² mm² -T83:REF -T83:UI3 -T30:DI3 -T30:REF Remark: Extra filter guard Cable-type: Black 1 2 mm² mm² Remark
PAGE 25
Pre-heat Temp. Pt 1000 Geniox Access CU27 Controller bypass Modulating -W369, -W445A, -W446A, -W447A Modulating Project: Date: 06-08-2020 =Sec.defrost+DVQ-QM47A 2 1 3 -W447A =Sec.defrost+DVQ-QM46A 2 1 3 -W446A 2 1 3 -W445A Pt1000 BK BN GY BK BN GY BK BN GY BK WH Black Brown Gray Remark: Cable-type: Black Brown Gray Remark: Cable-type: Black Brown Gray Remark: Cable-type: Black White mm² mm² mm² mm² mm² mm² mm² mm² mm² mm² mm² =Sec. defrost Box-X2:+ =Sec. defrost Box-X2.1:=Sec.
PAGE 26
Geniox Access CU27 Controller -W448A, -W449A, -W456, -W457 -W457 Fire thermostat -BR1 2 1 3 -W456 =Sec.defrost+DVQ-QM49A Modulating -BR2 Modulating -W449A 2 1 3 BN BU BN BU BK BN GY BK BN GY mm² mm² mm² mm² mm² mm² =Sec. defrost Box-X2:+ =Sec. defrost Box-X2.1:=Sec. defrost Box-KF5:AO5 =Sec. defrost Box-X2:+ =Sec. defrost Box-X2.1:=Sec.
PAGE 27
Room 1 Temp sensor -W458, -W507, -W508, -W513 P -W513 24V -BP3 Pt1000 -W508 Pt 1000 ANG Project: Date: 06-08-2020 ANG Pressure transmitter P DPT 0-10V Geniox Access CU27 Controller Outdoor Temp. -BT8 ** -BT7 Smoke det.
PAGE 28
P -W517/W520 24V RH sensor Extract/Room P G (24V) Project: Date: 06-08-2020 1 2 3 -W531.1 Out 1 (0-10V) -W514, -W515/516, -W517/W520, -W531.1 G0 (0V) -QM31.
PAGE 29
Geniox Access CU27 Controller -W531.1S, -W532.1, -W532.1S, -W551, -W553, -W571.1 Valve Pre-Heating Project: Date: 06-08-2020 2 3 1 1 2 3 -W571.1 Modulating motor -QM71.1 -QN53 Modulating motor -W553 2 3 1 -W551 1 2 -W532.1S 1 2 3 -W532.1 Valve Heating -QN51 Damper Motor -QM32.1S -QM32.1 -QM31.
PAGE 30
Geniox Access CU27 Controller -W571.1S, -W572.1, -W572.1S, -W580, -W581, -W583 Project: Date: 06-08-2020 -T30:REF -W581 -W583 Switch -T30:DI3 -W580 1 2 -W572.1S 1 2 3 -W572.1 Switch -SF3 -SF2 Damper Motor -QM72.1S -QM72.1 -QM71.1S 2 1 1 2 1 2 BN BU BK BN GY BN BU mm² mm² =A1-X5:1 =A1-X5:3 mm² mm² mm² =A1-X5:2 =A1-X5:1 =A1-X5:3 mm² mm² =A1-X5:1 =A1-X5:3 -T32:D1 -T32:REF:2 mm² mm² Remark: Ext.
PAGE 31
Geniox Access CU27 Controller -W584, -W601, -W602, -W642.1 14 15 16 24V Project: Date: 06-08-2020 U V W PE EC fan =A1+RHC-TA2 -X1 -GQ2 EC fan DI1 24V DI1 Switch 17 A 18 B 19 GND L N PE -W642.
PAGE 32
Geniox Access CU27 Controller Damper Damper -W645, -W646, -W655 Pressure Exchanger Project: Date: 06-08-2020 =A3+DVE-SA-BP8 A B 24VDC 0VDC -W655 C2 =BUS RS485+Extract air-QM46 C1 24V 0V -W646 BN GN WH YE BN GN WH YE BN GN WH YE mm² mm² mm² mm² mm² mm² mm² mm² Brown Green White Yellow mm² mm² mm² mm² Remark: Sec. defrost Cable-type: Brown Green White Yellow Remark: Extract Cable-type: Brown Green White Yellow Remark: Extract Cable-type: =Sec. defrost Box-X2:+ =Sec.
PAGE 33
Pressure Exchanger Geniox Access CU27 Controller BP8:B+ BP8:B- -W666, -W1000, -W332, -W532 +RHC-BG32 Main Switch 2 4 6 N =A1-W332 1 3 5 N +RHC-MA32 =A1-X1:PE -S10 -W1000 U1V1 W1PE Rotor Motor =A1-W532 PE PE BK BN BU mm² mm² mm² Project: Date: 06-08-2020 mm² mm² mm² Remark: Rotor sensor Cable-type: mm² mm² mm² mm² Remark: Rotor Motor Cable-type: Brown Blue 1 2 3 PE mm² mm² mm² mm² -KF1:24V -KF1:A+ -KF1:0V -KF1:B- +RHC-TA2:14 +RHC-TA2:16 +RHC-TA2:15 +RHC-TA2:U +RHC-TA2:V +RHC-TA2:
PAGE 34
Geniox Access CU27 Controller -W550, -W554, -W700, -W701, -W702 Project: Date: 06-08-2020 + - + =A1-W702 - =A1-W701 Light switch -EA2 2 3 1 =A1-W700 Modulating motor -EA1 Valve for cooling/ Change over -SF1 Mixer pump 1 =A1-W554 N PE BK RD BK RD BK RD 1 2 3 BN BU PE mm² mm² mm² mm² mm² mm² mm² mm² mm² mm² Black Red mm² mm² Remark: Light P20 Cable-type: Black Red Remark: Light P20 Cable-type: Black Red Remark: Light switch Cable-type: Black Gray Brown Remark: Cooling valve
PAGE 35
Geniox Access CU27 Controller Dual DPT -W703, -W704, -W705, -W661.1, -W662.1 Project: Date: 06-08-2020 Dual DPT T2+ T2- + + BK RD BK RD BK RD BN GN WH YE 24VDC 0VDC A B BN GN WH YE =A1 controller-W662.1 24VDC 0VDC A B =A1 controller-W661.
PAGE 36
Dual DPT Geniox Access CU27 Controller 24V DI1 -W662.2, -W343, -W442, -W444 Project: Date: 06-08-2020 =A3-W444 Pt1000 Exhaust Temp. +DVAF-EA-BT3 =A3-W442 Pt1000 Eff. Temp +DVAF-EA-BT2 A (D+) B (D-) GND =A3-W343 BP2:A+ BP2:ABP2:B+ EC fan BP2:B+DVE-SA-BT4 -GQ2 24VDC 0VDC A B Extract Temp. Pt1000 BK WH BK WH BK WH GN WH YE BN mm² mm² mm² mm² 0.25 mm² 0.25 mm² +DVE-SA-BP1:T2+ +DVE-SA-BP1:T2- 0.25 mm² 0.25 mm² Black White 0.25 mm² 0.25 mm² Remark: Extract Temp.
PAGE 37
Geniox Access CU27 Controller N PE BN BU PE Braun Blue GNYE mm² mm² mm² +PS230V-F1:1 +PS230V-F1:3 N PE L BN BU PE Brown Blue GNYE mm² mm² mm² +PS230V-F1:1 +PS230V-F1:3 Remark: motor supply air =EC Single/Twin+Supply air-W101 Cable-type: 1 =EC single-GQ1 =EC single-GQ2 18 18 18 18 18 18 Sheet L Remark: motor extract air =EC Single/Twin+Extract air-W102 Cable-type: Cable Plan 4 5 5 7 8 8 Path 1 -W102, -W101 Project: Date: 06-08-2020 Rev.: Sheet: 115 Geniox-Core CS 43.04.02 230V GB 43.