SAVE VTC 200 Installation instructions Document in original language | 254294 · v01 GB
© Copyright Systemair UAB All rights reserved E&OE Systemair UAB reserves the rights to alter their products without notice. This also applies to products already ordered, as long as it does not affect the previously agreed specifications. Systemair is not liable or bound by warranty if these instructions are not adhered to during installation or service.
Contents 1 Overview ......................................................1 1.1 General Description ................................1 1.2 Warranty ..............................................1 1.3 Type label.............................................1 2 Important Safety Information .............................1 2.1 Intended Use.........................................1 2.2 Admonitions .........................................2 3 Technical Data ................................................2 3.
Overview | 1 Overview 1.1 General Description Read the instructions carefully and in its entirety. For description of advanced settings and installation of accessories see Service and Accessories Installation manual. All documents can be found in our online catalogue at www.systemair.com. 1.2 Warranty For the assertion of warranty claims, the products must be correctly connected and operated, and used in accordance with the data sheets.
2 | Technical Data • The system should operate continuously, and only be stopped for maintenance/service. • Do not connect tumble dryers to the ventilation system. • Make sure that filters are mounted before starting the unit. 2.
Technical Data | 3.1 Dimensions and Weight Fig. 2 Dimensions of left hand unit * Height with mounting bracket. ** Drainage The unit weight is 47 kg.
4 | Technical Data The hatch can be lifted off by loosening a screw at the bottom of the unit. 3.2 Connections Left and Right models Fig. 3 Duct connections Position Description R Right hand model (Supply air connection is situated on the right hand side of the unit viewed from the front) L Left hand model (Supply air connection panel is situated on the left hand side of the unit viewed from the front) Symbol 3.3 3.3.
Delivery, Transport, Storage | the unit to outside (chimney effect). If no dampers are installed there is risk of condensation inside the unit and the outdoor ducts during these stop periods. It also might be that cold air from outside could pass the unit and enter into the building. That could cause condensation outside the supply and extract air ducts and even at the valves in the rooms.
6 | Prerequisites for Installation • Only remove the packaging shortly before assembly. • Beware of sharp edges during mounting and maintenance. Use protective gloves. 5 Prerequisites for Installation To ensure a proper and fail-free operation, it is important that the unit is installed according to these instructions. 5.1 Location and Space Requirements The SAVE VTC 200 should preferably be installed in a separate room (e.g. storeroom, laundry room or similar.).
Installation | C — concrete/bricks, W — wood block, G — gypsum, M — mineral wool X* — adaptable height according to needs. Make sure the mounting bracket is completely level.
8 | Installation Follow the ventilation drawing when connecting the unit to the duct system. 6.1 Condensation drainage Depending on the relative humidity in the extract air, condensation may occur on the cold surfaces of the unit. The condensate water is led out through the drainage (exhaust air side) situated on the bottom of the unit. A one meter hose with 13 mm (½″) connection and a hose clamp are included at delivery. Exhaust air side drainage is not mounted with an end cap at delivery.
Electrical connections | 6.3 Installation and Configuration of Accessories Please follow instructions included with the accessory or consult “Service and Accessories Installation” manual which can be found in our online catalogue. 7 Electrical connections 7.1 Main circuit board layout The SAVE VTC 200 is equipped with built-in regulation and internal wiring. Fig.
10 | Before Starting the System Position Description 15 Analog output 1 — Rotary heat exchanger control signal (for VSR, VTR type models) / Damper control signal (for VTC, VSC type models), UI6 — Bypass damper feedback signal (for VTC, VSC type models) 16 Terminals for speed control of extract air fan 17 Terminals for speed control of supply air fan 7.2 External connections (Connection board) External connections to the main circuit board are done via connection board situated inside of the unit.
Commissioning | • Outdoor air intake is positioned with sufficient distance to pollution sources (kitchen ventilator exhaust, central vacuum system exhaust or similar) • All external equipment is connected • The unit is correctly wired 9 Commissioning Follow the first startup instructions and fill in the Commissioning record as you go through the settings. The Startup Wizard cannot be skipped.
12 | Concluding Routines 10 Concluding Routines Perform the following procedures before leaving the site: 1. Ensure that the product is operational and that no alarms are active. 2. If applicable, save the configuration backup. 3. Make sure that the Commissioning record is complete. 4. Collect all tools. 5. Inform the appropriate person that work is finished. 6. Follow the procedures for the return and disposal of replacement parts and the disposal of packing.
EU Declaration of Conformity | 12 EU Declaration of Conformity Manufacturer EN 60529 Systemair UAB Linų st. 101 LT–20174 Ukmergė, LITHUANIA Office: +370 340 60165 Fax: +370 340 60166 www.systemair.com The manufacturer hereby confirms that SAVE VTC 200 comply with all applicable requirements in the following directives and regulations.
Phone +370 340 60165 Fax +370 340 60166 www.systemair.com SAVE VTC 200 · Installation instructions · 254294 · en_GB · 2021-03-10 · v01 Systemair UAB Linų st.