GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual System Planning Corporation 3601 Wilson Boulevard Arlington, VA 22201 (703) 351‐8700 www.globaltrak.com www.sysplan.com support@globaltrak.com Prepared: J.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual GlobalTrak™ Assembly, E‐Seal with ZigBee Interface V2 Operation Manual The purpose of the GlobalTrak™ Assembly, E‐Seal with ZigBee Interface V2 Operation Manual is to: • • Familiarize the user with the functions and capabilities of the GlobalTrak E‐Seal with ZigBee Interface V2 Provide a guide for operation procedures for the GlobalTrak E‐Seal with ZigBee Interface V2 Prepared: J.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual Table of Contents 1.0 GlobalTrak E‐Seal with ZigBee Interface V2 Overview ............................................................................ 4 1.1: GlobalTrak E‐Seal with ZigBee Interface V2 Overview................................................................................ 4 1.2: Feature List...........................................................................................................................
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual 1.0 GlobalTrak E‐Seal with ZigBee Interface V2 Overview 1.1: GlobalTrak E‐Seal with ZigBee Interface V2 Overview The GlobalTrak E‐Seal with ZigBee Interface V2 provides enhanced security capability to the GlobalTrak Asset Monitoring Units using a CT‐PAT electronic barrier seal.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual Figure 2. Bolt Figure 3. Locking Cap Prepared: J.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual 1.2: Feature List The product is designed to provide additional security information for assets monitored by Asset Monitoring Units. This is accomplished by equipping the GlobalTrak E‐Seal with ZigBee Interface with the following features: a) ZigBee Wireless: The wireless standard for low‐power short‐range bi‐directional communications, suitable for mesh networks and sensor reads. Line‐of‐sight of up to 250 meters.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual 2.0: Using the GlobalTrak E‐Seal with ZigBee Interface V2 2.1: Device Power Instructions 2.1.1: Power On 1. Insert the bolt into the hole on the side that says “enter”. Figure 4. Insert Bolt 2. Red and yellow LEDs will flash until the GlobalTrak E‐Seal with ZigBee Interface V2 begins communicating with a GlobalTrak Asset Monitoring Unit. The GlobalTrak E‐Seal with ZigBee Interface V2 will search for up to four minutes.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual Figure 5a & 5b. Searching for Asset Monitoring Unit. LEDs flashing. 2.1.2: Power Off 1. Remove the bolt and wait for the red LED to flash twice. Figure 6. Remove bolt, red LED flashes twice. 2. Insert the bolt again, and remove it after 1‐3 seconds. Note: A solid red light will show for 3 seconds, indicating that the device will shut down after sending a shutdown message. Prepared: J.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual 2.2: Installation 1. Close container door. 2. Seal the container by threading the bolt through the locking aperture on the truck door, and then through the “enter” port on the GlobalTrak E‐Seal with ZigBee Interface V2. Figure 7. Thread locking bolt through locking aperture and “enter” port. 3.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual 2.3: Removal & Deactivation 1. Remove the GlobalTrak E‐Seal with ZigBee Interface V2 by cutting the chimney of the locking body. Note: Bolt cutters are needed for removal. Figure 10. Cut locking body chimney. 2. Once the locking body is removed, proceed by pulling the GlobalTrak E‐Seal with ZigBee Interface V2 off of the bolt by using a downward motion. Figure 11. Pull body downwards. Prepared: J.
GlobalTrak™ Assembly 203026, E‐Seal with ZigBee Interface V2 Operation Manual Per FCC 15.21: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Per FCC 15.105: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
