Certification Exhibit FCC ID: U9O-RF26X FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0339.W06.11.A Manufacturer: Synapse Wireless Inc. Model: RF26X Manual 5015 B.U.
® DATA SHEET RF Engine 26X Series Model Number: RF26X Part Numbers: RF260PC1 RF261PC1 RF266PC1 Document Revision v1.0 © 2011 Synapse, All Rights Reserved All Synapse products are patented or patent pending Specifications are subject to change without notice – confirm that data is current Synapse, the Synapse logo, SNAP, and Portal are all registered trademarks of Synapse Wireless, Inc.
RF26X Data Sheet Document Number 430141-01A Page 2 of 14
Table of Contents 1.0 RF26X OEM Module Overview 1.1 Specifications 1.2 Module Pin Definitions 1.3 Electrical Characteristics 1.4 Mechanical Drawings 1.5 Board Mounting Configurations 2.0 Agency Certifications 2.1 United States (FCC) 2.1.1 OEM Labeling Requirements 2.1.2 FCC Notices 2.1.3 FCC Approved Antennas 2.2 Canada (IC) 2.2.
1.0 RF Engine 26X Series OEM Modules Overview The RF Engine 26X Series (Model Number RF26X) is an IEEE 802.15.4, low power, highly-reliable solution to embedded wireless control and monitoring network needs that require high data rates. The Model RF26X is pin-compatible with Digi International’s XBee and XBee-PRO RF modules.
Figure 1.0 Block diagram showing the major subsystems comprising the RF26X 1.1 Specifications Table 1.0. RF26X Specifications Performance Power Requirements General Networking Available I/O Agency Approvals RF26X Data Sheet Outdoor LOS Range Transmit Power Output RF Data Rate Receiver Sensitivity Supply Voltage Transmit Current (Typ@3.3V) Idle/Receive Current (Typ@3.3V) Power-down Current (Typ@3.
1.2 Module Pin Definitions Table 1.1. RF26X Module Pin Assignments Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name Description 3.
Table 1.3. ADC Electrical Characteristics (Operating) Symbol Parameter Condition Min Typical Max Unit VREFH3 Voltage Reference, High Programmable 1.5 1.6 1.8 V VINDC Analog input voltage Single Ended 0 1.8 0 3.3 3 4 4 Differential V VREFH is programmable to three fixed values; 1.5V, 1.6V, and 1.8V. The default is 1.6V. Each differential analog input may be as high as 3.3V but the differential voltage is still limited. Table 1.4.
1.4 Mechanical Drawings These drawings in Figure 1.1 show the RF26X module mechanical specifications. Figure 1.1 Mechanical drawings of the RF26X Module 1.5 Board Mounting Considerations The RF26X module is designed to mount into a receptacle (socket) on the host board. Picture 1.1 shows an RF26X module plugged in to an example host board. The receptacle sockets are on standard 2mm centers.
Host Board Example RF26X Mounted Picture 1.1 RF26X Mounted To Host Board 2.0 Agency Certifications 2.1 United States (FCC) The Model RF26X modules comply with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required. In order to comply with FCC Certification requirements, the Original Equipment Manufacturer (OEM) must fulfill the following requirements. 1. 2. 2.1.
MANUFACTURERS NAME BRAND NAME or TRADE NAME Figure 2.1 FCC Label Contains RF26X FCC ID: U9O-RF26X This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.1.
2.1.3 FCC Approved Antennas The RF26X modules are FCC-approved for fixed base station and mobile applications. The FCC requirement for mobile applications states that the antenna must be mounted at least 20 cm (8 in) from nearby persons. Notice: To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
RF26X Data Sheet Document Number 430141-01A Page 12 of 14
RF Exposure WARNING: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTICE: The preceding statement must be included as a CAUTION statement in OEM product manuals in order to alert users of FCC RF Exposure compliance. 2.
NOTE: The OEM can choose to implement a single label combined for both FCC and IC labeling requirements. If a combined single label is chosen, there must be a clearly visible label on the outside of the final product housing displaying the contents shown in Figure 2.3 below. MANUFACTURERS NAME BRAND NAME or TRADE NAME Figure 2.3 Combined FCC and IC Label Contains RF Engine FCC ID: U9O-RF26X Contains RF Engine IC: 7084A-RF26X This device complies with Part 15 of the FCC Rules.
