Certification Exhibit FCC ID: U9O-RF200A IC: 7084A-RF200A FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-2096 Manufacturer: Synapse Wireless, Inc. Model: RF200A User Manual 3998 FAU Blvd.
DATA SHEET ® RF Engine 200A Series Model Number: RF200A Part Numbers: RF200APD1 and RF200APF1 Document Revision v2.0 © 2013 Synapse, All Rights Reserved All Synapse products are patented or patent pending Specifications are subject to change without notice – confirm that data is current Synapse, the Synapse logo, SNAP, and Portal are all registered trademarks of Synapse Wireless, Inc.
Model RF200A Data Sheet ©2013 Synapse Wireless, Inc. · · Document Number 430133-01D 500 Discovery Drive, Huntsville, AL 35806 · 256-852-7888 · · Page 2 of 15 synapse-wireless.
Model RF200A Data Sheet ©2013 Synapse Wireless, Inc. · · Document Number 430133-01D 500 Discovery Drive, Huntsville, AL 35806 · 256-852-7888 · · Page 3 of 15 synapse-wireless.
Table of Contents 1.0 RF200APD1/RF200APDF1 OEM Module Overview 1.1 Specifications 1.2 Module Pin Definitions 1.3 Electrical Characteristics 1.4 Mechanical Drawings 1.5 Board Mounting Configurations 1.6 Ordering Information 2.0 Agency Certifications 2.1 United States (FCC) 2.1.1 OEM Labeling Requirements 2.1.2 FCC Notices 2.1.3 FCC Approved Antennas 2.2 Canada (IC) 2.2.1 OEM Labeling Requirements Model RF200A Data Sheet ©2013 Synapse Wireless, Inc.
1.0 RF Engine 200A Series OEM Modules Overview The RF Engine 200A Series (Model Number RF200A) is an IEEE 802.15.4, low power, highly-reliable solution to embedded wireless control and monitoring network needs that require high data rates. The RF200A embeds Synapse’s SNAP OS, the industry’s first Internet-enabled, wireless mesh network operating system into the Atmel ATmega128RFA1 single-chip AVR® microcontroller with an integrated transceiver that delivers up to 2Mbits/sec.
Figure 1.0 Block diagram showing the major subsystems comprising the RF200A 1.1 Specifications Table 1.0. RF200APD1 / RF200APF1 Specifications Performance Power Requirements General Networking Available I/O Agency Approvals Outdoor LOS Range Transmit Power Output RF Data Rate Receiver Sensitivity Supply Voltage Transmit Current (Typ@3.3V) Idle/Receive Current (Typ@3.3V) Power-down Current (Typ@3.3V) Frequency Spreading Method Modulation Dimensions Operating Temperature Up to 2 miles at 250 Kbps 18.
1.2 Module Pin Definitions Table 1.1.
1.3 Electrical Characteristics Table 1.2. RF200APD1 / RF200APF1 DC Characteristics Symbol VCC TOP VIH VIL 2 Parameter Condition Supply Voltage Operating Temp Input Hi Voltage Input Low Voltage VOL Output Low Voltage VOH Output High Voltage ILIN TX-ICC RX-ICC SHDN-ICC In Leakage Current Transmit Current Receive Current Sleep Current Min Typ 1 Max Units 3.3 3.6 85 0.4 V °C V V 0.4 V 2.7 -40 VCC - 0.
1.4 Mechanical Drawings These drawings in Figure 1.1 show the module with the RPSMA connector for use with an external antenna, and the keep put area for the F-antenna. There should be no copper, components, or fasteners on any layer of the host board beneath the keep out area. Figure 1.1 Mechanical drawings of the RF200APD1 and RF200APF1 Modules 1.5 Board Mounting Configurations The RF200PD1 and RF200PF1 modules are designed to mount into a receptacle (socket) on the host board. Picture 1.
to either the host board or to the enclosure to handle the mechanical stresses that can occur when an external antenna is screwed into the SMA. Picture 1.1 shows the RF200PD1 with RPSMA connector mounted to the host board. 1.6 Ordering Information Part Number Description RF200APD1 RF200APF1 802.15.4 Wireless Module with RPSMA connector 802.15.4 Wireless Module with PCB Inverted-F Antenna Host Board RF200APD1 Mounted Picture 1.1 RF200APD1 Mounted To Host Board 2.0 Agency Certifications 2.
1. 2. 2.1.1 The system integrator must place an exterior label on the outside of the final product housing the RF200A Modules. Figure 2.1 below shows the contents that must be included in this label. RF200A Modules may only be used with the antenna that has been tested and approved for use with the module. Please refer to the antenna table provided in this section. OEM Labeling Requirements NOTICE: The OEM must make sure that FCC labeling requirements are met.
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Recommended Antenna (RF200APD1): RF Exposure WARNING: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
MANUFACTURERS NAME BRAND NAME or TRADE NAME MODEL: RF200A Contains IC: 7084A-RF200A Figure 2.2 IC Label NOTE: The OEM can choose to implement a single label combined for both FCC and IC labeling requirements. If a combined single label is chosen, there must be a clearly visible label on the outside of the final product housing displaying the contents shown in Figure 2.3 below.
