User's Guide

2 3 4 5 6 7 8 9 11 1210
LED: Indicates an incoming call.
EARPIECE
MINI-HEADSET JACK: Plug
headset into phone for hands-
free use.
LCD SCREEN: Shows the status
of the phone and menu options.
SELECTION KEYS: Use to
select the option displayed on the
LCD screen.
END KEY: (Hard and Soft Key)
Use to end a call, refuse a call,
power off the phone and to return
to the previous menu.
FCT KEY: (Hard and Soft Key)
Use to access PBX specific
feature functionality.
Note: The
PBX specific features may be
available only if they are support
ed by the gateway and
programmed by the administrator.
HOLD KEY: Use to put a call on
hold and switch to the other line.
MOUTHPIECE
:
SERIAL PORT:
Use to download
software.
SND KEY: Use to call the number
dialed, accept a call, power on
the phone and to select and save
settings in the phone menus.
SCROLL KEYS: Use to move up
and down when selecting a feature,
option or to increase or decrease
call volume.
Battery Operations
Fully charge the battery for the
NVP before initial use of the
phone. Charge the battery
attached or detached from
the phone.
Charging the Battery
When charging the battery while
attached to the phone, turn off
the phone before inserting it into
the charger. Place the battery or
battery and phone combination
into the charger.
The LEDs on the charger indicate
the following:
GREEN indicates a fully charged
battery.
RED indicates the battery is
charging; wait until the LED
changes to GREEN before using
battery.
AMBER indicates the charger is
waiting to charge the other battery.
The charger charges the phone
first. The charging cycle for the
other device starts when the first
cycle finishes.
Removing the Battery
Remove the battery by depressing
the latch and pulling the top of the
battery away from the phone.
Note: When the battery latch
is opened. You will find the part
number, serial number and
manufacturing and regulatory
information located on the inside
compartment.
Replacing the Battery
Replace the battery to the phone
by aligning the feet on the battery
with the notches on the phone.
Push the top of the battery into the
phone until the latch clicks.
Basic Functions
Basic Functions introduces the
user to tasks, such as:
• Power on
• Login
• Logout
• LCD Icons
• Make a call
• Adjust call volume
• Receive a call
• End a call
• Keyguard
• Power off.
Power On
When powered on, the NVP
will associate itself with the RF
network and register with the
telephony gateway.
To power on the NVP, press SND.
The screen briefly displays the
NetVision splash screen containing
the phone firmware version
number.
Login
There are two different status
displays, one for shared mode
and the other for personal mode.
Personal Mode:
If your phone is configured in
personal mode, the phone profile
name displays with
Func
and
Menu
soft key options. If prompt-
ed, enter your user PIN. When you
are finished, press SND.
Note: Obtain a user name and
password (PIN) from the system
administrator.
Shared Mode:
If your phone is configured in
shared mode, a
User Login
screen displays.
1. Enter your extension number
or select your name using the
scroll keys.
2. Press SND.
3. If prompted, enter your
user PIN.
4. When you are finished,
press SND.
Logout
To logout of the network:
1. From
Menu
, select
Logout
.
2. Press SND.
User Login
displays on the LCD.
LCD Icons
Phone Lines -
Indicates on which line
a call is taking place.
Number 1 for line 1 and number 2
for line 2.
Signal Strength
Indicator -
Shows the RF signal
strength from the access point.
“X” -
Indicates that the phone
is not associated. Note:
When the phone is not associated,
it will beep three times and turn off
after 5 minutes.
Battery Strength -
When battery is low,
the battery indicator will begin
to flash and the phone will
beep once.
Make a Call
To place a call (to another NVP):
1. Enter extension number or
select name of the NVP by
using the scroll keys.
2. Press SND.
The phone displays the name or
number of the user being called.
Adjust Call Volume
When in an active call, adjust the
volume of the current call using the
scroll keys. Select from
Level 0
(low) to
Level 15
(high).
Receive a Call
For an incoming call, the caller ID
feature allows user to identify
callers before answering the call.
There are two types of incoming
call modes: no active call and
call waiting.
No Active Call
To accept an incoming call when
there is no active call taking place,
press SND.
Call Waiting
To accept an incoming call while
on an active call, press HOLD
and the phone will switch to the
second line to answer the call.
End a Call
To end a call, press END.
The LCD screen displays
Call Hangup
.
Keyguard
Lock the keypad in order to
prevent accidental phone
operation and unnecessary
battery power consumption.
Any incoming call can be
answered without unlocking
the keypad.
To lock keypad:
1. From
Menu
, scroll to
Keyguard
menu option.
2. Press SND.
Keys Locked
displays on the LCD screen.
--or--
The
NetVision Phone
(NVP) provides on-site, wireless voice communication capability. The NVP performs like a cellular phone.
Before use, the NVP requires configuration to the local network by the system administrator.
1
Soft Keys appear as text
on the LCD screen
: Use to return to the
previous menu.
: Use to ignore an incoming
call. When used, it disables
all ring tones temporarily.
Note: The incoming call
may still be answered by
pressing SND.
: Use to place a call.
: Use to clear an entry.
: Use to display the phone
user menu.
: Use to display name
directory.
: Use to accept an entry or
answer a call.
Battery
Latch
LEDs
Battery