User's Manual

ManualsBrandsSYMA MODEL AIRCRAFT INDUSTRIAL ManualsCamera & PhotoWifi-camera-1

-8-

Fine-tuning operation

Turn left/right fine-tuningSideward fly fine-tuningForward/Backward fine-tuning

When the quadcopter

keeps flying forward /

backward, you can correct

it by pressing fine-tuning

button down / up.

When the quadcopter

keeps flying to left / right

side, you can correct it by

pressing the fine-tuning

button right / left.

When the quadcopter

keeps rotating to left /

right, you can correct it

by pressing the fine-

tuning button right / left.

Ready to fly your quadcopter

1.Press the ON/OFF

power switch up.

2. Open battery cover,

and connect battery

connector with dash

receiver.

3. Enclose battery into

the fuselage, after

closing battery cover,

turn on the switch on

the bottom of aircraft.

4.Push the throttle lever to the highest position,

and then pull it back to the lowest position.

There will be one clear sound from the transmitter,

this shows that the quadcopter has entered into

the pre-fly state.

Summary of content (10 pages)

PAGE 1
Fine-tuning operation Forward/Backward fine-tuning When the quadcopter keeps flying forward / backward, you can correct it by pressing fine-tuning button down / up. Sideward fly fine-tuning When the quadcopter keeps flying to left / right side, you can correct it by pressing the fine-tuning button right / left. Turn left/right fine-tuning When the quadcopter keeps rotating to left / right, you can correct it by pressing the finetuning button right / left. Ready to fly your quadcopter 1.
PAGE 2
Function introduction 1.Low-voltage protection: If four indicator lights in the bottom of aircraft start to twinkle, it means that the aircraft is short of electricity and is not able to roll. At that time, a return voyage shall immediately be made to the aircraft. 2.Over-current protection: In the condition of rotating aircrafts fan blade, when being crashed or stuck, aircrafts circuit will conduct over-current protection. 3.
PAGE 3
Front Left Right Read 2. After aircraft connects with power supply, place the switch in ON position, adjust the direction pointed by aircrafts handpiece and regard it as the dead ahead in headless situation. 3. Push the accelerators push rod of remote control to the highest point and pull back to the lowest point. When remote control pops, it indicates that frequency modulation and forward definition have already finished. 2. Switch to headless function and general function 1.
PAGE 4
Battery replacement and charging method Steps of battery replacement: 1. Turn off aircrafts power supply, and push the switch to OFF. 2. Open aircrafts battery cover backward. 3. Connect battery interface with dash receiver. Steps of battery charge: 4. After battery replacement, fasten the battery cover again. ⭫ Ⓠ ᓝ 2. Connect charger to power supply socket. 1. Connect battery switch with charger. Balanced charger: 1.
PAGE 5
WIFI install camera Disassembly steps of camera: 1. Pull out power supply cable of the camera as shown in Figure (1). 2. Press safe lock of lower main body forcibly and pull back the camera simultaneously. Installation steps of camera: 1. Push the camera in place as shown in Figure (1). 2. Connect connecting line of camera with power supply socket of fuselages camera as shown in Figure (2).
PAGE 6
Maintenance procedure Problems Aircraft has no response Causes Solutions 1. Aircraft enters into low-voltage protection. 2. Electric quantity of remote control is insufficient, power indicator light will flicker. 3. Channel selection of remote control is inconsistent with aircrafts match codes. 1. Charge the aircraft. 2. Change remote controls battery. 3. Adjust channels of remote control and aircraft, and make them become consistent. 1.Change battery with better quality. 2.
PAGE 7
; : ; : ; : ; : Cear Motor A Motor B Main stand ; : ; : ; : ; : Blade cover Blade lockstitch Base of Dash Receiver Battery cover (White / Black) ; : ; : ; : ; : Receiver board Battery A/B adaptor& charge box Lampshades ; : WIFI Camera (White / Black) ; : Phone attaching clamp ; & Transmitter ; & Iron shaft Brerkdown&Dlagram Blade lockstitch WIFI camera -14-
PAGE 8
-15-
PAGE 9
PP PP Maln parameter PP PP Length of fuselage:500mm Height of fuselage:190mm Width of fuselage:500mm Battery:7.
PAGE 10
FCC statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.