Safety Instructions

ManualsBrandsSyber Sense ManualsElectronicsXPM-01

Table Of Contents

XPM-01 Motion Sensor Manual

DOC ID – 1706 • Rev 01

XPM-01 Motion Sensor Manual

Part number: XPM-01

Description

The XPM-01 is designed to fit seamlessly in the corner or the

room or alongside a wall/door. When the PIR senses motion it

transmits an alarm notification to the panel.

Important safety instructions–

Before you install this sensor, be sure to:

 Read, keep, and follow all instructions.

 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

 When there is a low battery, replace with a compatible

lithium ion battery.

Installation

Note: We recommend adding the motion sensor to a panel

before installation. Step 4 shows how to pair with a panel.

The motion sensor can be installed using the provided

adhesive and/or screws.

Note: We recommend using the provided screws for

installation. This method is more secure than using adhesive

alone.

To install the motion sensor:

1. Select the desired position for the sensor.

Note: The sensor only detects motion within 3.28 ft (1m)

in front of it (installed at 6.88 ft (2.1m) having a range of

32.80 ft (10m).

2. Remove the sensor’s battery pull tab.

3. Adhere the sensor to the wall using the provided screws or

adhesive.

Note: We recommend using the provided screws for

installation. This method is more secure than using

adhesive alone.

Screws

a. Locate the bottom of the sensor (the slotted flat

end), and then use a screwdriver to remove the

casing’s screw.

Gently slide a fingernail/fingertip into the slot and

push the top casing of the sensor upward.

Summary of content (6 pages)

PAGE 1
XPM-01 Motion Sensor Manual Note: We recommend using the provided screws for installation. This method is more secure than using adhesive alone. To install the motion sensor: 1. Select the desired position for the sensor. Note: The sensor only detects motion within 3.28 ft (1m) in front of it (installed at 6.88 ft (2.1m) having a range of 32.80 ft (10m). Part number: XPM-01 2. Remove the sensor’s battery pull tab. 3. Adhere the sensor to the wall using the provided screws or adhesive.
PAGE 2
g. Use the sensor’s casing screw to secure the cover. Adhesive c. a. Locate the bottom of the sensor (the slotted flat end), and then use a screwdriver to remove the casing’s screw. b. Gently slide a fingernail/fingertip into the slot and push the top casing of the sensor upward. c. Set the PINs and jumpers to the desired position. See, Pin function on page 4. d. Once the sensor is configured as desired, press the sensor cover against the base, until there is an audible snap. e.
PAGE 3
4. Battery replacement Add the sensor to the panel, by putting the panel in learning mode, then pressing the button on the side of the sensor to pair the sensor to the panel. The XPM-01 requires a CR123A battery. Once the battery is low, the panel displays a low battery icon next to the sensor in the devices list. The battery must be replaced within 7 days of the first low battery notification. If the battery is not replaced within 7 days, the sensor may not function properly.
PAGE 4
5. Press the sensor cover back onto its back plate. There will be an audible snap. 6. Use the sensor’s casing screw to secure the cover 7. Test the sensor. Table 1: Pin configuration Configuration Pet Immunity Sensitivity Top and middle pin Up to 33lb dog Low – max of 19ft (6m) distance range Middle and bottom pin Up to 55lb dog High – max of 32ft (10m) distance range Pin function The PIR Motion Sensor has 2 sets of adjustable pins.
PAGE 5
Specifications 6. Replace the sensor plate, and then continue to installation. – or – Wireless signal range 820.21 ft. (250 m) Transmitter frequency 433.95MHz TX Encrypted Yes Pet immunity 33 to 55lb dog Detection length Default: 32.80 ft. (10 m) Optional: 19.68 ft. (6 m) Detection angle 90 degree Mounting height 7.5 to 9.5 ft. (2.28 to 2.89 m) Transmitted indications Tamper Low battery Adjust the sensitivity level, and then and then continue to installation.
PAGE 6
Regulatory information Manufacturer Syber Sense North American standards ETL listed to: UL 639, ULC S306 FCC compliance FCC ID: 2AVDC-XPM-201 2004/108/EC (EMC directive): Hereby, Syber Sense declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.