Safety Instructions

ManualsBrandsSyber Sense ManualsElectronicsXPD-01

Table Of Contents

XPD-01 Door/Window Sensor Manual

DOC ID – 1705 • Rev 01

XPD-01 Door/Window Sensor Manual

Part number:

Door/Window Sensor, White (XPD-01-W)

Door/Window Sensor, Brown (XPD-01-B)

Description

The XPD-01 Door/Window Sensor is a magnetic sensor device

designed to fit seamlessly alongside a door frame or windowsill.

When the door or window are opened, the magnetic contact is

disrupted, and the sensor transmits an alarm notification to the

control panel.

Important safety instructions

Before you install this sensor, be sure to:

 Read, keep, and follow all instructions.

 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

 Do not expose the device to water.

 When there is a low battery, replace with a compatible

lithium ion battery.

Installation

The door/window sensor can be installed using the provided

adhesive or screws.

Mounting orientation

The sensor and magnet should be placed near the top of the

door with the sensor attached to the unmoving part of the

closure. For example, attach the main body of the sensor to

the door frame, not the door. We recommend that the sensor is

placed in the top corner of the opening side of the door, see

Figure 1.

Figure 1: Sensor orientation

The sensors and magnet each have a slightly engraved line.

This line denotes where the sensors align to function properly.

If the sensor and magnet, when together/closed, do not line up

correctly, the sensor will not report correctly. See Figure 2, on

page 2.

Summary of content (5 pages)

PAGE 1
XPD-01 Door/Window Sensor Manual  When there is a low battery, replace with a compatible lithium ion battery. Installation The door/window sensor can be installed using the provided adhesive or screws. Mounting orientation The sensor and magnet should be placed near the top of the door with the sensor attached to the unmoving part of the closure. For example, attach the main body of the sensor to the door frame, not the door.
PAGE 2
Figure 2: Sensor alignment c. Remove the adhesive film cover. (Optional) d. Place the back plate against the door frame/windowsill, making sure that the orientation is correct for the desired position. Note: Once the adhesive is secure, the sensor cannot be moved. To install the door/window sensor: 1. Select the desired position for the sensor and magnet. Notes   The sensor and magnet must be within .25 inch of each other on final installation.
PAGE 3
Adhesive a. Select the desired position for the sensor. b. Peel one side of the adhesive tape, and then press the tape firmly against the sensor. d. (Optional) Mark the screw hole locations, then using a power drill, drill holes and install the 2 provided wall anchors. e. Insert the first screw into a screw hole, and then use a screwdriver to partially secure the screw in the wall. Do not fully insert the screw until the second screw has secured the magnet position. f.
PAGE 4
Table 1: Sensor and magnet gap range Non-metallic surface Supports Metallic Surface Open Close Direction Open Close 31 mm 29 mm X 30 mm 25 mm 34 mm 31 mm Y 36 mm 35 mm 35 mm 31 mm Z 45 mm 40 mm 4. Battery replacement The XPD-01 Door/Window Sensor requires a CR2032 battery. Once the battery is low, the panel displays a low battery icon next to the sensor in the devices list. The battery must be replaced within 7 days of the first low battery notification.
PAGE 5
Regulatory information Manufacturer Syber Sense North American standards ETL listed to: UL 634, ULC ORD634 FCC compliance FCC ID: 2AVDC-XPD-201 2004/108/EC (EMC directive): Hereby, Syber Sense declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.