SWIT Electronics Co., Ltd.
Preface 1. All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2. All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners. 3.
Safety Precautions Please follow the safety precautions before using. The following conditions are not covered by warranty. 1. Unauthorized repairs or other Unauthorized operations. 2. Inappropriate placement including but not limited to lighting, fire, exposure to rain, water or gas. 3. Using the wrong power supply. Warning Do not get any liquid inside the products Do not block the ventilation openings or put substances inside, in order to avoid short circuit, fire or electric shock.
1. Product Introduction FLOW2000 includes transmitter and receiver, adopts the latest encrypted transmission technology, and supports SDI and HDMI wirelessly transmitted in 600 meters scale (Line-of-Sight), 2 channels SDI/HDMI digital video transmission, auto pairing and OLED display. FLOW2000 is equipped with DC power connector, compact size, portable, and the receiving signal is very stable. 2. Features ◆ HD/SD-SDI and HDMI transmission Support up to 1080p 50/60Hz SDI & HDMI wireless transmission.
3. Appearance Instruction Transmitter FLOW2000 ⑴ Antenna ⑵ Product label ⑶ Link:Wireless status indicator ⑷ Video:Video signal indicator ⑸ Power:Power status indicator ⑹ OLED:0.96-inch OLED ⑺Five-direction switch:Five-direction adjustment button (adjust the display menu to switch and confirm in five directions: up, down, left, right, and vertical) ⑻ Installation thread:1/4”-20 thread. Use the package supplied articulating arm trestle to install the device to the camera.
The description of LED status indicator Receiver FLOW2000 ⑴ ⑵ ⑶ ⑷ ⑸ ⑹ ⑺ ⑻ ⑼ ⑽ ⑾ Antenna ON/OFF:Power switch USB:Micro USB, software upgrade interface Link:Wireless status indicator Video:Video signal indicator Power:Power status indicator DC in:Support DC 7-34V voltage input, 5.5mm (outer diameter) /2.1mm (inner diameter). Outside: negative, Inside: positive OLED:0.96-inch OLED Five-direction switch:Five-direction adjustment button.
The description of LED status indicator 4. OLED Display Boot Screen Main Screen (When Tx and Rx both have no signal connection, (When Tx and Rx have normal signal connection, Tx and Rx display the same. Fig.1) Tx and Rx display the same. Fig.2) Signal source No signal Signal format Auto channel mode Frequency switch Signal strength Signal strength Fig.1 Fig.2 Remark: Channel switch is adjusted up or down by the red five-direction adjustment button under OLED, 7 wireless channels in total.
REBOOT" prompts to REBOOT. After that, setting is ok. 4. To set several receivers to receive signal from one transmitter simultaneously (one transmitter to multi-receivers mode), we need to set all receivers except for "HOST" mode to "SLAV" mode, and then, push the five- direction switch up and down, select "SLAV" and press the five- direction switch. At the bottom of the screen, "PLEASE REBOOT" prompts to REBOOT. After that, setting is ok.
6. In one transmitter to multi-receivers mode, when “SLAV” mode receiver and transmitter are paired, the "HOST" mode receiver must be powered on. 7. The way to get the best effective of Wireless Transmission ⑴Set the antenna on both transmitter and receiver vertically straight up, no request to spread. If installed flat, still keep the antenna vertically straight up to extend transmission distance and stabilize transmission quality. (Fig.9) Fig.
⑵ Set the receiver as high as possible to avoid interference. ⑶ Avoid walls, trees and water to reduce signal attenuation.
8.
9. Specification Model FLOW2000T Transmitter FLOW2000R Receiver Input SDI×1、HDMI×1 / Output SDI×1 HDMI×1、SDI×2 Video format 1080I(60∕59.94∕50)∕1080PsF(24∕23.98)∕720P(60∕59.94∕50)∕1080P (60∕59.94∕50∕30∕29.97∕25∕24∕23.98) Wireless frequency 5180~5220MHz and 5760~5820MHz modulation mode OFDM transmission distance 600m(Line of sight) Power consumption ≤8W ≤8W Transmitting power / / Human-Machine Interaction 0.
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.