WS 8355 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 © Swing-N-Slide Inc.
Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statesments and warnings reduces the likelihood of serious or fatal injury This playset has been designed for use by a maximum of thirteen occupants at one time having a combined weight of 1,365 pounds. This playset is intended for use by children from (2) to (10) years of age. On-site adult supervision for children of all ages is recommended.
PLAYSET MAINTENANCE Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by our warranty. To help minimize these natural defects we recommend applying a sealer or stain every two or three years, or more often as the climate dictates.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
PLAYSET SAFETY ZONE 21'-3 5/8" 14'-0" 6'-0" 6'-0" 6'-0" 28'-0" 28'-0" 11'-9 3/16" 6'-0" 6'-0" 14'-0" 2'-0" 33'-3 11/16" MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
TOOLS REQUIRED DRILL 1/2” & 7/16’’ SOCKETS & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SCREWDRIVER PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 1/8” DRILL BIT HELPFUL ASSEMBLY INFORMATION Your playset consists of several boxes or modules. It is important to ensure all lumber, accessories and hardware is accounted for. The following pages list the contents of each box. Use these pages to take an inventory of all parts.
(2) [PF 6010] 1’’ x 3-3/8’’ x 47-1/2’’ TOWER MODULE SA 6081 (1) [PF 6011] /SA6022 1’’ x 3-3/8’’ x 47-1/2’’ BOARD LIST (4) [PF 6062] 1’’ x 3-3/8’’ x 42-1/2’’ ROOF A-FRAME TOWER MODULE: SA6042 (4) [PF 6164] 3’’ x 3’’ x 94’’ 6008] 3/4’’ x 5-3/8’’ x 42’’ A-FRAME BASE (2)(7) [PF[PF 6063] 3/4’’ x 3-3/8’’ x 59-5/8’’ (1) [PF 6020] 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT (3) [PF 6006] 3/4’’ x 3-3/8’’ x 44-1/2’’ (9) [PF 6013] 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD (1) [PF 6019] 2-11/16’’ x 5-3/8’’ x 93’’ SW
TOWER MODULE SA 6081 /SA6022 COMPONENTS CONT.
1/4”-20 x 1-1/4” Hex Bolt (x12) 5/16”-18 x 6-1/2” Carriage Bolt (x12) 5/16”-18 x 6” Carriage Bolt (x3) 5/16”-18 x 2-1/2” Hex Bolt (x2) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 4” Hex Bolt (x5) 5/16”-18 x 6” Hex Bolt (x2) 5/16”-18 x 7” Hex Bolt (x1) 5/16”-18 x 8-1/2” Hex Bolt (x1) FS2831 3 5/16-18 T-Nut (x28) Small FS2830 2-1/2 1/4’’ Loc Washer (x12) FS2829 2 FS2831 3 FS2830 2-1/2 FS2829 FS2831 32 FS2828 FS2830 1-3/4 2-1/2 FS2831 FS2827 FS2829 3 2 1-5/8 FS2826 F
/16’’ x 3’’ x 62’’ A-FRAME SUPPORT (2) [PF 6060] 5/8’’ x 5-3/8’’ x 13’’ SUN ’’ x 3-3/8’’ x 83’’ A-FRAME LEGS ’’ x 3-3/8’’ x 60’’ ROCKWALL SUPPORT 8’’ x 3-3/8’’ x 58’’ A-FRAME SUPPORT TERRACE MODULE SA 6031 (4) [PF 6001] 5/8’’ x 5-3/8’’ x 9-1/4’’ BOARD LIST TERRACE MODULE: SA6001 (1) [PF 6061] 1-1/2’’ x 1-1/2’’ x 40’’ (2) [PF 6028] 1-3/8’’ x 3’’ x 79’’ 8’’ x 3-3/8’’ x 43-1/2’’ 8’’ x 3-3/8’’ x 17-1/4’’ SLIDE STAKE (2) [PF 6026] 1’’ x 3-3/8’’ x 42’’ 8’’ x 3-3/8’’ x 15-1/2’’ DECK SUPPORT (3) [PF 6005]
6004] 3/4’’ x 3-3/8’’ x 24-3/4’’ 42’’ (2) [PF 6150] (6) [PF 6135] 3/4’’ x 5-3/8’’ x 26-1/4’’ LADDER MODULE: SA6005 (5) (1) [PF 6005] 6023] 3/4’’ x 3-3/8’’ x 42’’ 22-1/2’’ LADDER MODULE SA6005 (2) [PF 6002] 3/4’’ x 3-3/8’’ x 22-1/2’’ BOARD LIST (10) [PF 6021] 5/8’’ x 5-3/8’’ x 30-3/4’’ (1) [PF 6034] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-L PICNIC TABLE MODULE SA6018 (1) [PF 6035] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-R BOARD LIST (2) [PF 6058] 5/8’’ x 3-3/8’’ x 30’’ (1) [PF 6029] 5/8’’ x 3-3
SIDEWINDER BOARD LIST (2) [PF 6014] 1-1/2’’ x 3-1/2’’ x 36’’ (2) [PF 6012] 1-1/2’’ x 3-1/2’’ x 15’’ Sidewinder Slide (x1) SIDEWINDER SLIDE HARDWARE FS2831 3 FS2830 2-1/2 2-1/2” Deck Screw (x10) FS2829 2 30mm Deck Screw (x2) FS2828 1-3/4 FS2827 1-5/8 3/4’’ 5/16”-18 x 3/4” Hex Bolt (x9) #14 x 1” Truss Screw (x6) FS2826 1-1/4 FS2826 3/4 1-1/2’’ 5/16” Loc Nut (x9) 5/16” Washer (x18) 12 2’’
STEP 1 6’’ 47-1/2’’ Flush ’’ 5/8 9x5 /8’’ 3-3 SE x ’ A ’ 3/4 ME B 3 6 RA 60 A-F PF 6’’ (3) 2-1/2’’ Screws ’’ 01 01 F6 P (3) 2-1/2’’ Screws ’’ 1/2 /8’’ 7x4 -3 x3 T-Nut Small PF 6164 3’’ x 3’’ x 94’’ PF 6164 3’’ x 3’’ x 94’’ (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 59-1/4’’ 006 6 PF 3 ’’ -3/8 x3 /4’’ ’’ 1/2 4x4 FRAME A (2) 2-1/2’’ Screws Hint!! Use parts from your Tower Box. 2-1/2” Deck Screw (x14) 1. Assemble Frame A as shown above.
STEP 2 6’’ (3) 2-1/2’’ Screws Flush /8’’ 5 59x ’ ’ -3/8 E x3 ’ AS ’ 4 3/ EB 3 M 606 -FRA A PF 6’’ PF 6164 3’’ x 3’’ x 94’’ (3) 2-1/2’’ Screws 0 01 F6 P ’’ -3/8 3 1’’ x PF 6164 3’’ x 3’’ x 94’’ 47-1/2’’ ’’ 1/2 7x4 T-Nut Small (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 59-1/4’’ PF 6 600 (2) 2-1/2’’ Screws ’’ 3/4 /8’’ -3 x3 x /2’’ 1 44- (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME B 2-1/2” Deck Screw (x14) 1-1/2’’ ALL JOINTS 1.
STEP 3 (3) 2-1/2’’ Screws Check to make sure structure is square (3) 2-1/2’’ Screws Flush PF 600 53 /4’’ PF x3 -3/8 ’’ x 600 53 /4’’ x3 -3/8 ’’ x 42’ ’ (2) 2-1/2’’ Screws 42’ ’ PF 600 43 /4’’ x3 -3/8 ’’ x 42’ ’ Flush (2) 2-1/2’’ Screws PF 600 43 /4’’ x3 -3/8 ’’ x 42’ ’ (3) 2-1/2’’ Screws PF FRAME A 2-1/2” Deck Screw (x13) 1. Attach support boards to Frame A as shown.
STEP 4 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME B (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x13) 1. Attach Frame A to Frame B as shown.
STEP 5 PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (6) 1-3/4’’ Screws (2) 2-1/2’’ Screws (6) 1-3/4’’ Screws PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ 16-1/2’’ PF 6011 1’’ x 3-3/8’’ x 47-1/2’’ 16-1/2’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (2) 2-1/2’’ Screws PF 6011 1’’ x 3-3/8’’ x 47-1/2’’ FS2831 3 FS2830 2-1/2 FS2829 2 FS2831 FS2828 3 1-3/4 1-3/4” Deck Screw (x12) TOP VIEW FS2830 FS2827 2-1/2 1-5/8 2-1/2” Deck Screw (x4) 1. Install Deck Boards as shown.
STEP 6 (7) PF 6008 3/4’’ x 5-3/8’’ x 42’’ (6) 1-3/4’’ Screws per board 1 0 9 8 7 6 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 3/8’’.
STEP 7 Flush (3) 1-3/4’’ Screw per joint (4) 3’’ Screw NOTE: PRE-DRILLED HOLES Flush NOTE: Insert Hardware From Outside 005 6 PF 1 (3) 2-1/2’’ Screws 0 9 1 8 07 1-3/4” Deck Screw (x6) 2-1/2” Deck Screw (x6) 1 96 3” Deck Screw (x4) 0 6 8 9 1. Install Deck Supports as shown.
STEP 8 Check to make sure structure is square (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer T-Nut Small PF 602 61 ’’ x 3 -3/8 ’’ x 4 2’’ 47-1/4’’ Flush Hint!! Use parts from your Terrace Box. 2-1/2” Deck Screw (x4) 1. Install Deck Support Board as shown.
STEP 9 Check to make sure structure is square PF ’’ x /4 53 600 x /8’’ 3-3 ’ 42’ (3) 2’’ Screws PF 6028 1-3/8’’ x 3’’ x 79’’ PF 6028 1-3/8’’ x 3’’ x 79’’ (3) 2’’ Screws Flush PF Flush 5 600 ’’ 3/4 (3) 2’’ Screws /8’’ -3 x3 x ’ 42’ (3) 2’’ Screws FS2831 3 FRAME CFS2830 2-1/2 FS2829 2 FS2828 1-3/4 1. Assemble Frame C as shown.
STEP 10 Check to make sure structure is square PF ’’ x 6 1 026 3 ’’ -3/8 2’’ x4 5/16-18 X 2’’ Hex Head Bolt 47-1/4’’ 5/16’’Loc-Washer 5/16’’ Washer (2) 2’’ Screws T-Nut Small 1 0 9 8 7 2” Deck Screw (x4) 1. Install Deck Support Board as shown.
STEP 11 Flush With Outside Face of 1-3/8’’ x 3’’ Check to make sure structure is square Flush With Outside Face of 1-3/8’’ x 3’’ Flush With Top of Frame (2) 2-1/2’’ Screws PF 602 53 /4’’ Flush With Top of Frame -3/8 ’’ x 2 9-1 /4’’ (2) 2-1/2’’ Screws 3/4 ’’ x PF 60 3-3 /8’’ 25 x2 9-1 (2) 2-1/2’’ Screws x3 3/4 ’’ x PF 6 3-3 025 /8’’ x2 9-1 /4’’ /4’’ Flush With Outside Face of 1-3/8’’ x 3’’ 50-5/8’’ (2) 2-1/2’’ Screws 3/4 ’’ x PF 60 3-3 /8’’ 24 x2 7-3 Flush With Outside Face of 1-
STEP 12 Check to make sure structure is square (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws (3) 2-1/2’’ Screws 79’’ (2) 2-1/2’’ Screws FRAME C 1. Attach Frame C to Tower as shown.
STEP 13 (1) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ (1) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ 31 30 10-5/8’’ 10-5/8’’ 29 PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ 8 27 6 TOP VIEW 1-3/4” Deck Screw (x10) 1. Install Deck Boards as shown.
STEP 14 (6) PF 6135 3/4’’ x 5-3/8’’ x 26-1/4’’ All Boards Flush (6) 1-3/4’’ Screws per board Note: Holes 1-7/8’’ From Edge on This Side 31 0 9 8 7 6 6 1-3/4” Deck Screw (x36) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 7/16’’.
STEP 15 PF 6022 3/4’’ x 3-3/8’’ x 19-1/2’’ (3) 2’’ Screws 50-5/8’’ 1 0 9 8 7 2” Deck Screw (x3) 1. Install Barrier Support Boards as shown.
STEP 16 PF 6005 3/4’’ x 3-3/8’’ x 42’’ (6) 2-1/2’’ Screws 53-7/8’’ 2-1/2” Deck Screw (x6) 1. Attach Gap Filler Boards as shown.
STEP 17 (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ NO GAPS BETWEEN BOARDS (4) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws #12 x 3/4” Pan Screw (x4) INSIDE VIEW 30mm Deck Screw (x12) 1. Install Barrier Boards as shown.
STEP 18 (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ 2-1/8’’ 2-1/8’’ 2-1/8’’ 30mm Deck Screw (x12) 1. Attach Barrier Boards as shown.
STEP 19 PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ Flush (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws PF 6005 3/4’’ x 3-3/8’’ x 42’’ PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ Flush (2) 2-1/2’’ Screws 62-5/8’’ FS2831 3 FS2830 2-1/2 1. Install Barrier Support Boards as shown.
STEP 20 1’’ 3-1/8’’ 3-1/8’’ 1’’ 1-5/8’’ PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 1/2’’ GAP PRE-DRILL (4) 1/8’’ HOLES 1/2’’ GAP PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ 4-7/8’’ FS2831 3 FS2830 2-1/2 PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 17-3/8’’ (4) 30mm Screws per board PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ FS2829 2 FS2828 1-3/4 (10) 3/4’’ Screws per Window Frame PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ x2 FS2827 2-13/16’’ 1-5/8 x2 2-13/16’’
STEP 21 1’’ (4) 30mm Screws per board (4) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws #12 x 3/4” Pan Screw (x8) 30mm Deck Screw (x24) 1. Install Window Panels.
STEP 22 PF 6020 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT TOP OF BEAM SUPPORT 84’’ FROM BOTTOM OF POST Loc Nut 5/16’’ Washer Wood Loc-Washer 5/16-18 X 6’’ Carriage Bolt 1. Install Swing beam support as shown.
STEP 23 CENTER PF 6019 2-11/16’’x5-3/8’’x93’’ Swing Beam TOWER THIS SIDE T TH OWE IS R SID E = DRILL HERE (6 PLACES) MARK HOLE LOCATION 30mm Deck Screw (4 per Clamp) 5/16”-18 x 6-1/2” Carriage Bolt BOTTOM VIEW SIDE VIEW 5/16” Clamp, Beam 2-1 PF 1/1 6 601 Sw ’’x5-3 9 ing /8 Be ’’x93 am ’’ HD Swing Hanger NOTE HOLE LOCATIONS NOTE HOLE LOCATIONS 5/16” Washer A-FRAME THIS SIDE 5/16” Loc Nut 1. Locate the PF 6019 Swing Beam in your kit. 2.
STEP 24 PF 6018 2-11/16’’x3’’x62’’ A-Frame SB Support 5/16”-18 x 7” Hex Head Bolt (1) 3’’ Screws (1) 3’’ Screws 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 6017 1-3/8’’x3-3/8’’x83’’ A-Frame 5/16”-18 x 2-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Washer (2) 2-1/2’’ Screws 5/16”-18 x 4” Hex Head Bolt (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 5/16-18 T-Nut Small PF 6016 1-3/8’’x3-3/8’’x58’’ A-Frame Support 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut
STEP 25 (2) Swing Beam Bracket 5/16”-18 x 3-1/2” Hex Head Bolt x2 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/2” Hex Head Bolt 5/16” Washer x2 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
STEP 26 Beam Brace 5/16”-18 x 3 1/4” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 1. Install Swing Beam Brace as shown.
STEP 27 5/16”-18 x 6” Carriage Bolt 5/16”-18 x 8-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16” Wood Loc Washer 5/16” Washer 5/16” Loc Nut 1. Install Swing Beam as shown.
STEP 28 (4) 30mm Screws per board (6) PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ BARRIER BOARD SPACING: Outer boards will be flush against 3’’ x 3’’ Uprights. All boards inbetween will have a 3/4’’ gap. 30mm Deck Screw (x24) 1. Install Barrier Boards as shown.
STEP 29 (1) 3’’ Deck Screws 1-5/8’’ 1-5/8’’ 13-1/2’’ PF RA F ’’ x PF 1 62 3- ’’ 3/8 2 x4 OO R ’’ /2 -1 FA ME 60 PF 6058 5/8’’ x 3-3/8’’ x 30’’ (4) 30mm Deck Screws Check to make sure structure is square 60 62 1’’ x3 -3 /8’ ’x 42 -1 /2’ ’R OO FA -F RA ME x2 3/4’’ CENTERED PF 6060 5/8’’ x 5-3/8’’ x 13’’ SUN (4) 30mm Screws 3” Deck Screw (x2) x2 1. Assemble Roof A-Frames as shown.
STEP 30 (4) 30mm Screws (6) 30mm Screws (1) PF 6056 5/8’’ x 2’’ x 10’’ (2) PF 6059 5/8’’ x 2’’ x 7’’ x2 Note: Place screws through A-Frame and into end of PF 6053 CENTERED Note: PF 6053 Rests on Top of PF 6056 (2) 2-1/2’’ Screws 2’’ / 3-1 4 PF 6053 1-3/8’’ x 3-3/8’’ x 43-1/2’’ SIDE VIEW (2) 2-1/2’’ Screws Note: Place screws through A-Frame and into end of PF 6053 2’’ / 3-1 4 FS2831 3 FS2830 2-1/2 30mm Deck Screw (x20) 1. Assemble the Roof frame as shown.
STEP 31 3/4’’ Offset Each Side (3) 1-5/8’’ Screws Side View (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws 1-5/8” Deck Screw (x12) 1. Attach Roof Frame to Tower as shown.
STEP 32 PF 605 03 /4’’ x3 (4) 2’’ Screws (4) 2’’ Screws PF 605 03 /4’’ x3 -3/8 ’’ x 43- 1/2 ’’ 1 2” Deck Screw (x8) 1. Attach Roof Side Support Boards as shown.
STEP 33 (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer 3/4” Pan Head Screw (x6) 1. Attach Tarp as shown.
STEP 34 x -3/8’’ 035 1 PF 6 ’’ 3-3/8 x 66- -1/4’’ RT-R 6 ’’ x 6 PPO 3-3/8 R SU E LADD 1/4’’ x -3/8’’ 034 1 PF 6 -L ORT UPP ER S LADD (2) 2-1/2’’ Screws per Rung (2) 2-1/2’’ Screws per Rung (5) PF 6032 1’’ x 3-3/8’’ x 18-1/2’’ PF 6029 5/8’’ x 3-3/8’’ x 20-1/2‘’ (4) 2-1/2’’ Screws 2’’ Hint!! Use parts from your Ladder Box. 2-1/2” Deck Screw (x24) 1. Assembly Ladder as shown.
STEP 35 (3) 2-1/2’’ Screws Panel Bracket (4) 3/4’’ Pan Screw Underdeck View 2-1/2” Deck Screw (x3) #12 x 3/4” Pan Screw (x4) 1. Attach Ladder to Tower as shown.
STEP 36 Flush (4) 30mm Screws per board 1-5/8’’ GAP TO UPRIGHT BOTH SIDES (4) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ NO GAPS BETWEEN BOARDS Under Deck View PF 6024 3/4’’ x 3-3/8’’ x 27-3/4’’ (4) 2-1/2’’ Screws 31’’ 2-1/2” Deck Screw (x4) 30mm Deck Screw (x16) 1. Install barrier support and barrier boards as shown.
STEP 37 (4) 2’’ Screws (2) PF 6039 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT 3’’ (4) 1-1/4’’ Screws (2) PF 6037 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT 2-3/8’’ 3’’ 11-1/4’’ (2) PF 6133 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE OUTSIDE FACE TO OUTSIDE FACE (4) 2’’ Screws (4) 1-1/4’’ Screws 2-3/8’’ 6-7/8’’ OUTSIDE FACE TO OUTSIDE FACE 6-7/8’’ (2) 2’’ Screws 36’ ’ (2) PF 6038 1’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG (2) 2’’ Screws PF 6040 1’’ x 5-3/8’’ x 41-1/2’’ BENCH FS2831 3 Check to make sure
STEP 38 ALIGN SCREWS WITH PRE DRILLS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD (6) PF 6389 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARDS 1 (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD 0 9 8 7 2” Deck Screw (x32) 1. Align and install rock wall boards to the image above.
STEP 39 Panel Bracket (4) 3/4’’ Pan Screw (3) 2-1/2’’ Screws Underdeck View 2-1/2” Deck Screw (x3) #12 x 3/4” Pan Screw (x4) 1. Attach Rock Wall as shown.
STEP 40 (2) 1/4’’ T-Nuts (2) 1-1/4’’ Hex Head Bolts (2) 1/4’’ Flat Washer Per Rock (2) 1/4’’ Loc-Washer Per Rock 1. Attach Climbing Rocks as shown.
STEP 41 PF 6452 1-3/8’’ x 3-3/8’’ x 22’’ (2) PF 6180 5/8’’ x 3-3/8’’ x 10-1/2’’ (4) 1-3/4’’ Screws From Behind Deck Support (6) 30mm Deck Screws Flush to Support Flush to Upright Underdeck View Underdeck View (2) 30mm Deck Screws PF 6009 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake Grade 1” Truss Screw (x3) 30mm Deck Screw (x8) 1. Attach Slide Support Boards and Slide as shown.
STEP 42 (2) [PF 6014] 1-1/2’’ x 3-1/2’’ x 36’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Nut (4) 2-1/2’’ Screws per board 5/16’’ Washer 30-1/2’’ (4) 2-1/2’’ Screws per board 12’’ (2) [PF 6012] 1-1/2’’ x 3-1/2’’ x 15’’ (4) 1’’ Truss Screws (1) 1’’ Truss Head Screw per side Attach brace here (2) 30mm Deck Screws PF 5999 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake Grade 2” 12’’ FS2831 3 FS2830 2-1/2 45’’ 2-1/2” Deck Screw (x8) FS2829 2 FS2828 1-3/4 30mm Deck Screw (x2) 1” Truss Screw (x6) FS2827 1.
STEP 43 1/4” Washer 1/4’’ x 1-3/4” Pan Screw 11” Back View Front View 1/2” Pan Screw (x2) 1-3/4” Pan Screw (x2) 1. Attach Safety Handle and I.D. Tag as shown.
STEP 44 FIG. A HD Ring-Trap Combo Assembly 1. Attach Ring-Trap Chain to Swing Hanger as shown in (Fig. A). 2. Tighten Quick Link to secure chains to Swing Hangers as shown in (Fig. A).
STEP 45 FIG. A 83 Ha 8" Minimum HD Swing Seats 1. Attach Chain to Swing Hanger as shown in (Fig. A). 2. Tighten Quick Link to secure chains to Swing Hangers as shown in (Fig. A). NOTE: O nce installed, there must be a minimum 8’’ clearance between the bottom of the swings and the surfacing.
STEP 46 5/16” Washer Fold up Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 1. Place swing set in final location and mount Anchor-It(s) at locations circled above. 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at: www.OnlineWarranty.net Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment to providing quality residential playground products.
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration Benefits of registering online: ■ Quick & simple from home or mobile ■ Record your purchase in our system ■ Initiate product warranty ■ Improved customer support ■ Notification of new product information Register your product online at www.OnlineWarranty.
