Remote Controller User Manual www.swellpro.
Remote Controller Illustration [01] [14] [02] [13] [03] [04] [05] [06] [12] [11] [10] [09] [07] [08] [15] [01] 2.4G Remote Antenna For drone control signal [02] Return-Home Switch Commands the drone to return automatically [03] Camera Tilt Down Button Tilts the camera down [04] Follow Me Button Controls the drone to follow the remote controller [06] Left Joystick Control the drone’s ascent (up), descent (down) and/or to rotate the aircraft nose left or right.
Remote Controller This section introduces the remote controller functions, including the drone operation and the camera operation. Charging Remote Controller Battery The Spry remote controller has a built-in battery and charging circuit. Charge the controller using the supplied micro-USB cable and a regular 5V /2A USB charger. Some USB ports and some USB cables cannot provide the full 2 amps (2A) of power required.
Flight Modes Remote Control Operation GPS Circle Flight ATTI Description GPS：GPS mode Circle Flight：Orbit mode ATTI：ATTI mode Note: In circle mode, by activating the Follow Me mode the aircraft can fly around a moving object as long as the speed of moving objects is less than 4 m/s (15km/h). Follow Me Mode Remote Control Operation Follow Me Green Status light indicates good GPS fix.
Remote Controller Pairing Remote Control Operation Description 1. To pair the remote controller to the drone, hold the Return Home switch down and simultaneously power on the remote controller. 2. The remote controller will vibrate and beep twice. The Controller Status Light will flash red and green. 3. Power on the drone. After pairing has completed, the Controller Status Light will turn green. 4. Long-press the FPV channel button.
Camera Control Remote Control Operation Description Long-press the camera button (five beeps) to start or stop video recording. Short-press the camera button (two beeps) to take a photo. You cannot take a photo if video recording is started. After taking a photo, the camera information window will display a camera icon Photo/Video and the resolution of the photo. The card In video mode, the card icon indicates the remaining hours and minutes (hh:mm) the microSD card can hold.
APP Control How to Use The Spry remote controller has a built-in WI-FI module that can be used to connect your mobile device and control the aircraft to perform various intelligent automatic flight modes with the Spry APP. APP installation: The Spry app is available for iOS and Andoid devices. Android systems can download the APK from either the Android market or our website www.swellpro.com.
1. Once you have a minimum of 8 GPS satellites, you can unlock the drone and start flying with the remote controller or click the “takeoff” button on the APP, set the take off altitude and then slide to unlock, the drone will ascend automatically and hover. 10 11.2V GPS Take-off Drag to set take-off height: 3m Cancel -10 Ok I I I I I I I 10 I I 10 -10 0 D: 0.0m H: 0.0m H.S: 0.0m/s V.S: 0.0m/s Lat：113.860667 Ing：22.704291 Lat：113.860667 Ing：22.704291 10 11.
10 11.2V GPS 0 Delete Upload Lat：113.860667 Ing：22.704291 Lat：113.860667 Ing：22.704291 10 11.2V GPS Point Edit Altitude：66m FlySpd: 4.0m/s Hover Time: 3sec LNG:113.8698811 LAT: 22.6258727 Cancel Ok 3. Flight Path Setting a.Tap the “Flight Path Setting” at the top of the screen and tap the map to set the flight path (double tap the flight point to delete it, tap the “Delete” button to delete all flight paths). Tap the flight point again to edit. b.
APP control requires a good wireless communication environment. If the drone does not execute the operation command, this may be due to interference, please try again. If the drone continually fails to respond to your APP commands, please operate the drone with the remote controller: quickly switch the Flight Mode switch once, it is suggested to use the GPS mode to take over control. FCC Statement This device complies with part 15 of the FCC rules.
