4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Note United States Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Product Model List： ： Model AS;9104DU AS;3104DU AS;9108DU AS;3108DU AS;9116DU AS;3116DU AI;9104DU AI;9108DU AI;9116DU Specification 4 input (USB & PS.2) 1 output（PS.2), Supporting cascade & hub 8 input (USB & PS.2) 1 output（PS.2), Supporting cascade & hub 16 input (USB & PS.2)1 output（PS.2), Supporting cascade & hub 4 input (USB & PS.2) 1 output（PS.2), Supporting cascade & hub&IP Control 8 input (USB & PS.2) 1 output（PS.
/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Content Overview .................................................................................................................................................................................. 6 Common Language Introduction .......................................................................................................................................... 7 Chapter 1 ...........................................................................
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual F2 SCAN： ............................................................................................................................................................ 26 F3 LIST：............................................................................................................................................................... 27 F4 QV：...........................................................................................................
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Overview This User Manual will assist you in the effective use of the product features, including the installation, setup and operation of the equipment. You will find the following in this manual: Chapter 1: Overview This chapter introduces the Rack;Mountable KVM Switch system, including its functions, features, and benefits, aslo describes the front and rear panel components.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Common Language Introduction Symbol Text Information 【】 The parentheses indicate the keys that need to be entered. For example, [Enter] means to press the Enter key. For keys that need to be entered at the same time, they are placed in the same bracket, and the keys are joined by a plus sign. For example: 【Ctrl + Alt】 1.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Chapter 1 Introduction Product Introduction 4/8/16 Port USB, PS2 Rack;Mountable KVM Switch is a 4/8/16 VGA computer that allows administrators to access a USB keyboard, mouse, or PS2 keyboard, mouse, and console from a group Multi;functional equipment.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Features One console controls 4 , 8 or 16 computers Be compatible with USB / PS/2 keyboard and mouse in console and PS/2, USB keyboard and mouse in computer.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual HARDWARE REQUIREMENT Console A set of VGA display screen, which is compatible with the installation architecture to install any computer under the highest resolution A set of USB interface mouse A set of USB interface keyboard A group of PS/2 interface mouse A set of PS/2 interface keyboard IP remote control terminal 1000M network interface (optional installation) Computer The following equipment must be installed on each computer: A group of VGA
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Operation System Operation System Windows Linux RedHat SuSE Debian Ubuntu UNIX AIX FreeBSD Sun Solaris Mac Novell Netware Version Windows 2000/XP/2003/2008/Vista/7/10 9.0 or higher 10/11.1 or higher 3.1/4.0 7.04/7.10 4.3 or higher 5.5 or higher 8 or higher OS 9.0~10.6 (Snow Leopard) 6.0 or higher More operating system support, please pay attention to the latest version of the relevant product compatibility.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Component Front View 4 port selection switches 8 ports selection switches 16 ports selection switches 1&2 No. 1 2 3 3 Section Function Port Selection Press a switch button to access the computer attached to its Switches corresponding port.The internal buzzer beeps, it means that the switching action is performed correctly, The selected port LED will light up as well. Port LEDs The port LEDs are built into the Port Selection Switches.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Rear View 4 port KVM rear view 8 port KVM rear view 5 3 4 16 port rear view 6 No. Section 2 1 Function Port to connect computer.Connect one end of the VGA connector of the corresponding KVM cable to this, and the other end of the keyboard connector to the port corresponding to the PC. (Refer to the description of "Cable" in the relevant section.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual If you purchase the product does not contain IP expansion module is similar to the product shown below. 1No IP Module Rear View The part marked with "1" is the external baffle of the extended IP module, and it needs to be removed and replaced to install the IP module. (For details, refer to the description of the hardware installation section.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Chapter 2 Installation Placement and Installation The KVM switch can be placed in any suitable plane and sufficient to securely support the weight of the equipment plus additional cables. Cabinet Installing 1. Remove the two screws on the left and right side of the front of the unit (two screws in total). 2. Use the screws supplied with the package rack assembly kit to secure the rack retention tabs to the front of the unit. 3.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual hole of the mounting plate with the mounting hole on the rack. Use the rack mounting screws in the mounting bracket to secure the mounting plate to the front end of the rack tight.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Expansion IP Module Installation If you buy a KVM switch, and need to increase the remote control and operation, you canbuy the IP module directly from the dealer for equipment upgrades and expansion, the operation method is simple and quick, can quickly enhance the integrated management of KVM Application ability.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual 4. Take the extended IP module and push it gently into the recess in the mounting module cavity as shown. 5. Push the IP module to the bottom, and then tighten the IP module with the two screws which removed from the front panel. 6.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Single device installation Note: Before installation, make sure that the equipment is powered off. To prevent damage to the equipment during installation, make sure that all the devices installed are well grounded. To install a single;level KVM, refer to the following online diagrams (numbered in the order of steps on the online graph) and operate as per bellowing: 1.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Cascade device connection This product can be cascaded to increase the number of controlled devices, combined with IP remote control mode can be flexibly used in a variety of user environment requirements.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual The cascade mode, it’s the same method of keyboard, mouse and computer connectionsas stand;alone connection, this part will not repeat them, the number part of the description is as follows: 1. A cascaded KVM switch can be connected in two ways by using a USB KVM cable (as shown in connection number 2 in the figure) or a PS/2 KVM cable (as shown in connection number 1 in the figure) Connect to the upper;level switcher. 2.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Chapter 3 Basic Operation Hot Plug The KVM switch supports hot;swapping, removing and removing components by unplugging the cable from the computer's connection port without shutting down the switch. To make the hot swap function work properly, please follow the steps as below.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Manual Selection Use the buttons on the front panel for port selection. OSD Menu Screen Selection (Please check the OSD Operation Chapter for more information) Hot key Selection This product offers four methods for hot;key switching: 【SCRLL】+【SCRLL】+【NUM】 【CTRL】+【CTRL】+【NUM】 【SHIFT】+【SHIFT】+【NUM】 The default hot;key toggle key combination is【SCRLL】+【SCRLL】+【NUM】, the【NUM】is the keyboard no.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Chapter 4 OSD Operation OSD Introduction OSD (On Screen Display), provides a menu driven interface to handle the computer switching procedure to provide instant access to any computer on the installation. OSD Log in The OSD function provides a two;level (administrator / user) password mechanism.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual 【F1】 ;;; 【F6】 at the bottom of the screen is the function setting of OSD menu, and corresponding operation and setting of corresponding function by keyboard. After entering the OSD main screen, the port number in the center of the screen is the port number of the selected PC. To move up and down through the list one line at a time, use the【↑】【↓】Arrow Keys, press 【Enter】 to select the switch port.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual 3. Press the【Esc】key to return to the previous menu. F1 GOTO： ： Press the 【F1】 key to start the GOTO function. The GOTO function allows you to switch directly to the connection port by typing the port name or its port number. 1. To use “NAM” method, move highlight bar to “NAME”, press 【Enter】, input name of a port, then press [Enter] to confirm. 2.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual F3 LIST： ： The LIST function lets you broaden or narrow the scope of which ports the OSD displays on the main screen. Many of the OSD functions only operate on the computers that have been selected for listing on the main screen with this function. The choices and their meanings are given in the table below: Choice Meaning ALL Lists all of the ports on the installation. QVIEW Lists only the ports that have been selected as Quick View Ports.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Move the highlight bar to a port, press [F4], an icon of up triangle appears. Press [F4] again, the icon disappears. F5 EDIT： ： EDIT function creates or edits the name of a port. Press [F5], a pink edit box will appear on the screen. Input name, and then press [Enter], the port is set a name and it will also appear on the screen. F6 SET： ： SET function settings can be set to the administrator and the user to set the OSD menu.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual 1.Move the highlight bar to an option, press 【Enter】to enter a setting option. 2.After selecting an item, the sub;menu and the further options provided will appear. To select it, double;click the mouse or move the selection column to the option, and then press the [Enter] key, an icon will appear. Select the option before to indicate that the item has been selected.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual SWITCH HOTKEY It provides you with four hotkey combinations: 【SCRLL】 【SCRLL】 【NUM】、 【CTRL】 【CTRL】 【NUM】、 【ALT】 【ALT】 【NUM】、 【SHIFT】 【SHIFT】 【NUM】You can use the keyboard 【↑】 【↓】 to move cursor to select, and then press 【Enter】 key to save. The defaultis to use【SCRLL】【SCRLL】【NUM】as the OSD menu start hotkey. 【NUM】 is the numeric keypad of the keyboard. The valid numeric range is 【1】 ; 【16】.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual CHANNEL DISPLAY DURATION Time the tip window last. Options are following: 3 SECOND The tip window lasts for 3seconds. ALWAYS ON The tip window always on the screen. CHANNEL DISPLAY POSITION Position of the tip window. A small blue window appears on the screen. Use arrow key to move it, then press [Enter] to specify the position. SCAN DURATION Duration for scanning one port.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual SET PASSWORD Set new password. First enter old password, then enter new password and confirm it. The new password is set. If error occurs, the screen will remind users. SET SUPER PASSWORD 设置管理员密码时，需要正确输入原来的密码。才可以更新新密码，连续正确输入两次，新密码 生效。When setting the administrator password, you need to enter the correct password. Before new password is updated, input the previous password twice, the new password to take effect.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual LOCK CONSOLE You cannot switch or scan after you lock the console (including switch by push button on the panel or OSD). You need to enter password to set. Note: After Locking the console, you can also unlock the console by this option. It also needs password verification.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Appendix Safety Instruction In General This product is for indoor use only. Please read all the instructions for future reference. Follow all the warnings and instructions on the device. Do not place this equipment on any unstable surface (such as cart, stand, table, etc.). If this equipment falls,it will cause serious damage. Do not use this equipment near water. Do not place this equipment near or over the radiator or heating equipment.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual qualified service representative for repair.
4/8/16 Port USB/PS2 Rack Mountable KVM Switch User Manual Specification Function Computer Direct Connections Cascade(Max) CPU Port Selection Console Connectors Video Keyboard Mouse Connector Computer Video/Key Connectors board/Mou se Power IP Module Network Interface Toggle Connection Port Switch Selection KVM Reset IP Module Reset IP Module Default LEDs Computer Selection Port On Line IP Module Network Interface Analog Mode Keyboard, Mouse Video resolution (Max) Scan time interval Operating Operating tem
