User's Manual

ManualsBrandsSuzhou Sate Auto Electronic ManualsElectronicsTPMS Transmitter

TSB23

Sensor User Manual V1.0

1 of 5

TSB23 Sensor User Manual

1 General Description

1.1 Purpose

Ｉｔ　ｉｓ　ａ　Ｖａｌｖｅ　Ｓｔｅｍ　Ｄｅｖｉｃｅ　ｔｈａｔ　ｗｏｒｋｓ　ｏｎ　ａｉｒ　ｐｒｅｓｓｕｒｅ． This manual is to make

　ｓｕｒｅ　ｔｈｅ　ｒｅｌｉａｂｉｌｉｔｙ　ｏｆ　ｃｏｍｍｕｎｉｃａｔｉｏｎ　ｂｅｔｗｅｅｎ　ｒｅｃｅｉｖｅｒ　ａｎｄ　ｓｅｎｓｏｒ，　ａｎｄ　ｔｉｇｈｔｎｅｓｓ　

between sensor and wheel hub.

2 Basic Requirements

2.1 Tire valve

2.1.1 Suitable pore size for tire valve

The valve is suitable for wheel hub with tire valve pore size of Φ11.5±

0.2mm.

2.1.2 Valve nut dimension

Valve nut O.D. is Φ14mm, length is 19mm。

2.2 Housing

Housing of the sensor must be sealed to meet water proof and dust proof

requirement, with protection degree IP54. The housing material should make the parts

meet vibration, shock and drop requirement, and tests for vibration, shock and drop

should comply with test requirements of IS016750-3 2007 《 Road Vehicles ─

Environmental conditions and testing for electrical and electronic equipment》.

Housing material: PA6+GF30 (black)

2.3 Dimension requirement

TSB23 dimension is as below:

Summary of content (5 pages)

PAGE 1
TSB23 Sensor User Manual V1.0 TSB23 Sensor User Manual 1 General Description 1.1 Purpose ＩｔｉｓａＶａｌｖｅＳｔｅｍＤｅｖｉｃｅｔｈａｔｗｏｒｋｓｏｎａｉｒｐｒｅｓｓｕｒｅ． This manual is to make ｓｕｒｅｔｈｅｒｅｌｉａｂｉｌｉｔｙｏｆｃｏｍｍｕｎｉｃａｔｉｏｎｂｅｔｗｅｅｎｒｅｃｅｉｖｅｒａｎｄｓｅｎｓｏｒ，ａｎｄｔｉｇｈｔｎｅｓｓ between sensor and wheel hub. 2 Basic Requirements 2.1 Tire valve 2.1.1 Suitable pore size for tire valve The valve is suitable for wheel hub with tire valve pore size of Φ11.5± 0.2mm. 2.1.2 Valve nut dimension Valve nut O.D.
PAGE 2
TSB23 Sensor User Manual V1.0 Item Size Length 76mm Width 63mm Height 26mm Remark Including tire valve 2.4 Installation requirement 4N.m(±0.5 N）torque force should be employed to screw tire valve nut when install TSB23 sensor to make sure the installation reliability.
PAGE 3
TSB23 Sensor User Manual V1.0 ② Screw the sensor nut by hand, and employ 12mm sleeve to tighten it（torque force 4N.M）. ③ Mount the rubber tubes; ④ Inflate the tires to standard pressure, and check whether there is leakage between the valve and lock nut with soap water; ⑤ Screw the valve cap on to finish sensor installation; ⑥ Check the tire’s dynamic balance after sensor installation, and then install the other three sensors one by one, and mount the tire.
PAGE 4
TSB23 Sensor User Manual V1.0 Note: During installation, the sensor need to be clean, not polluted by lubricant oil, etc; During tire mounting and dismounting, the sensor shouldn't be touched; During tire inflation and deflation, no force should be employed to the sensor; 2.5 Temperature requirement Operation temperature and storage temperature range of TSB23 sensor are as below: Parameter Temperature range Unit Minimum Maximum Operation temperature -40 125 ℃ Storage temperature -40 85 ℃ 2.
PAGE 5
TSB23 Sensor User Manual V1.0 FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.