RTG-TPMS INSTALL MANUAL RTG-TPMS-8 INSTALL MANUAL Revision:V 1.04 Suzhou Sate Auto Electronic Co.
RTG-TPMS INSTALL MANUAL Content RTG-TPMS OVERVIEW 1. Instruction for Master Installation--------------------------------3 1) Master Overview------------------------------------------------3 2) Instruction for led indication----------------------------------5 3) Setting------------------------------------------------------------6 2. Instruction for Repeater Installation------------------------------8 3. Instruction for Sensors Installation-------------------------------9 4.
RTG-TPMS INSTALL MANUAL RTG-TPMS-8 OVERVIEW RTG-TPMS-8 is the tire pressure monitoring system for the gantry crane, it monitors the pressure of tire full-time and alerters the driver with sound and light, at the same time the system can mutually interchange information with PLC, PC via communication socket. The system is made up of sensors, repeater and master. It can offer monitoring for 8 tires at most. Figure 1 Master Figure 2 Repeater 1. Master Install Manual 1.
RTG-TPMS INSTALL MANUAL 2. Accessories of Master (1)Power Wire 3-metre long power wire (2)Communication Wire Figure 4 Communication Wire 3. Installation Step 1.Fasten the Master on right position in the cab Screw Position M3X10 Figure 6 Screw Positions for Installing the Master 2. Adjust the angle of antenna to be vertical to master, screw the locknut on the antenna tightly.
RTG-TPMS INSTALL MANUAL 3.Connect the power wire Plug power plug into master power socket, and fasten power wire with tie. Note: Connect the red wire to anode 24V and black wire to cathode, screw the nut tightly. Figure 8 Power Wire Socket 4.Connect the communication wire Plug DB9 connector into the Master socket, screw the nut tightly Figure 9 Communication Wire Socket Note: If no request, communication wire may not be installed.
RTG-TPMS INSTALL MANUAL automatically. LED light will return into green or red depended on pressure value until information of the sensor can be received. 5.Setting Guide 1)Sensor ID Setting 1) Press ID key and hold it for 3 seconds long, then release the key, as shown below. Digital “1” began to flash, at this time you can adjust it to the tire number you want by key ,such as ↑ 、 ↓ , and then press ENTR . If you want to exit the setting of ID modified, adjust to” E” and then press ENTR to exit.
RTG-TPMS INSTALL MANUAL 3)Setting Pressure Unit Press ENTR key and hold it 3 seconds long, then release it. picture like down will be shown, digit 1 will flash, at this time adjust the digit to 2 by ↑ 、 ↓ , then press ENTR 。 At this time enter the step as below. You can press ↑ 、 ↓ key to choose one from two alternation pressure unite in Psi (abbr. P) and bar (abbr.
RTG-TPMS INSTALL MANUAL 5)Display Pressure Value in turn Pressure value of all tires will be displayed in turn when no action of pressing key on Master. The first digit on the left indicates current tire number (1-8). The second digit indicates current unit of pressure, “P” stands for “psi”, “b” for “bar”. The back four digits indicate current pressure.
RTG-TPMS INSTALL MANUAL 2. Repeater Installation Manual 1. Assemble position sketch map The four repeaters should be installed on the I-section Beam of the equipment. They are on upper and lower side of the RTG separately. 2. Installation Step: Prepare Tool: screwer, M13 aid-spanner, M10 spanner, 3M insulating tape, fastening tie. 1. Fixing repeater at bottom board of the I-section beam, place proof-water connector adown. Fill up rubber gasket and fasten screws. 2.
RTG-TPMS INSTALL MANUAL 4.Mechanism Characteristic Figure 10 3. Repeater Size Sensor Installation Manual 1.
RTG-TPMS INSTALL MANUAL 2. Installation Step 1) All the 8 Sensors are labeled with tire position numbers and ID code numbers, shown as below: Sensor for tire number 5 ID Code Figure 12 ID Code: 012012 2) Enter the corresponding Sensor ID Codes into the Master according to the tire position numbers shown below. Refer to Step 5.1 for the way to enter the codes. Figure 13 Tire Position Number 3) Screw the cap off the valve, then screw on the provided M14 locknut toward the tire valve.
RTG-TPMS INSTALL MANUAL 4) Use M3 socket head wrench to tighten the 6 locknuts. M14 Locknut Locknut Figure 14 Installation of the triple-valve assembly for Sensor 5) Screw on the tire valve cap to the inflating end of the triple-vale. 6) Check if there is air leakage through soap bubbles. 3. Notes: 1)Check if all accessories are all ready before installation and if it is tight between rubber washer and plug, whether it is trim on the side.
RTG-TPMS INSTALL MANUAL Reason: 1. The power of repeater does not connect well 2. Light fails to work. Solution: 1. Measure by multimeter whether i nput vol t age is 24V. (1) No, check the power supply of system (2)Yes, next step 2. Replace transmitter, and hand it in the technologist. 3.Master 1. No display and No sound of Key Reason: power is not connected well. Solution 1.Check the power a. yes, replace the Master b. no. check system of power supply. 2. LED light has no indication.