Installation Manual

Before installation, ensure adequate separation between the locations of the outside antenna and Inside antenna – at least 25 ft.
1. FIND AREA OUTSIDE WITH STRONGEST SIGNAL
Using your phone, identify the outside location with the strongest signal. Generally, this is found on the side facing your nearest
cell tower and as high as possible.
Note that Bars are not always a reliable measure of signal. The best way to conrm signal coverage is the ability to place and hold
a call. For specic dB signal measurements, use the methods below. Note that dB measurements appear as a negative number
where the closer to 0, the stronger the signal (eg. -100 dB would be considered a weak signal while -65 dB a strong signal).
Apple iPhones: Dial *3001#12345#* and press Call. In the top-left corner, a dB number appears instead of bars.
Android devices: download the app “Network Signal Info” in the Google Play store.
This signal booster requires a minimum cellular signal reading of -100dB at the location of the outside antenna. Signal between
-70dB and -90dB is recommended for best performance.
Please note: Signal stronger than -50dB may cause the aected frequency bands to turn o.
2. INSTALL THE OUTSIDE ANTENNA
Once you have located the area of strongest signal, mount the antenna to a pole or pipe
(not included) at the highest possible elevation. The directional Yagi antenna works best
when facing the direction of your carrier’s cellular tower. To nd the location of your carrier’s
closest cell tower go to www.cellreception.com.
To install the outside antenna, assemble the u-bolt, bracket, nuts and washers as shown
in the illustration. Keep the connections loose enough to allow the antenna to rotate until
the optimum direction is found.
Note: The outside antenna may be installed on a variety of pipe angles. Ensure that the
mounting area has at least a 12-inch radius clear of obstructions and other radiating
elements and orient the antenna vertically with the drip hole at the bottom.
Once the outside antenna is secured to a pipe or pole, connect one end of the provided
50 ft. coax cable to the antenna and tighten the connection.
3. INSTALL THE SIGNAL BOOSTER AND INSIDE ANTENNA
Choose a location for mounting the directional panel antenna on vertical surface. The antenna should be at the approximate
height of your cell phone when in use and facing a central area where signal is needed. Please note: Be sure to provide enough
separation from outside antenna - at least 25 ft. Also, the outside and inside antennas should face away from one another.
Using the plate, mark position of desired screw placement and screw mounting plate into place with the slide panel protruding
towards you (see panel antenna illustration below). Slide antenna securely onto mounting plate.
To install the booster, select a location that is near the inside panel antenna and a working AC outlet*. Use the supplied screws
or appropriate screws for surface of mounting location and drill through screw tab holes on booster (see Booster Components
Diagram illustration) and mount the booster to a wall.
Connect the inside antenna and booster by connecting one end of the provided 20 ft. of coax cable to the inside antenna and
the other end of the cable to the booster port marked “INSIDE” and hand-tighten the connection.
Next, connect the outside antenna and booster by connecting the remaining end of the 50 ft. cable leading from the outside
antenna to the port of the booster marked “OUTSIDE”.
4. CONNECT POWER
Connect the AC power cord to the booster and plug into a 110V AC power outlet. Once the booster has been completely
assembled, turn the booster’s power switch on.
Note: If the Power LED does not turn ON or the Alert LEDs continue to ash, see the Troubleshooting section. This booster is rated for 5-15V input
voltage. DO NOT use the booster with a higher voltage power supply. This can damage the booster, cause personal injury and void your warranty.
CONFIGURE GAIN SETTINGS
The SureCall gain dials should always be at maximum level unless the control light in a specic band is ashing red or ashing
red-yellow. In either of these cases, the rst action should be to increase the antenna isolation between the inside and outside
antenna as much as possible and restart the booster. If the situation continues, you can lower the gain with an attenuator or, as
the last resort, reduce the booster gain by 5dB at a time until the control light in the frequency band ashes yellow.
Coax Cable (50 ft.)
Power Supply
Signal Booster
Inside Antenna
Outside Antenna
Coax Cable (20 ft)
Install Overview
Quick Install Guide
Outside Antenna Assembly
Nut
Washer
U-bolt
Bracket
Download the complete manual at www.SureCall.com
SC-PolyH3-72-YP-CA / SC-PolyH-72-YP-Kit Rev3 11.05.18
Contents
Connector to Inside Antenna
44
OFF
54
64
44
OFF
54
64
45
OFF
55
65
52
OFF
62
72
51
OFF
61
71
Connector to Outside Antenna
Power Jack
Power Switch
Booster Components Diagram
Troubleshooting
Problem Resolution
Signal booster has no power Connect the power supply to an alternate power source.
Verify that the power source is not controlled by a switch that has removed power from
the outlet.
If the POWER LED on the signal booster remains OFF, contact tech support at:
1-888-365-6283 or [e-mail]
After completing installation,
indoor signal coverage has not
improved
( 1) Verify that all cable connections are tightly tted. (2) Try further separating the booster
and antenna. (3) Verify that there is usable signal where the outside antenna is placed.
 Remember: Bars are not always a reliable measure of signal. The best way to conrm
signal coverage is the ability to place and hold a call.
Specications
Fusion4Home 3.0 (US) Fusion4Home 3.0 CA (Canada)
Uplink Frequency Range (MHz): 698-716 / 776-787 / 824-849 / 1850-1915 / 1710-1755
Downlink Frequency Range (MHz): 728-746 / 746-757 / 869-894 / 1930-1995 / 2110-2155
Maximum Gain: 72 dB
Supported Standards: CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all cellular standards
Input Impedance: 75Ω donor port / 50Ω server port
Noise Figure: 8 dB
AC Input: Input AC110V, 60 Hz; Output DC 5-15V
Maximum Output Power: 1 Watt EIRP
Cable: RG6 / SC-240
RF Connectors: F Female / N Female
Power Consumption: <15W
Operation Temperature: -4º to +158º F
Certications FCC ID: RSNF4HOME IC: 7784A-F4HOME
Fremont, CA 94538 USA | +1-888.365.6283 | [e-mail] | www.surecall.com
© 2018. All Rights Reserved
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent
to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specied by the manufacturer. Antennas MUST be installed at least 20 cm
(8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider.
WARNING: E911 location information may not be provided or may be inaccurate for calls served by using this device.
This device may operate in a xed location only, for in-building use.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
3-Year Warranty
Thank you for your SureCall purchase. Please register your new product at www.surecall.com/activate (US) or
www.surecall.com/CA/activate (Canada)
SureCall warranties its products for three years from the date of purchase against defects in workmanship and/or materials.
Products returned by customers must be in their original, un-modied condition, shipped at the customer’s expense in the orig
-
inal or protective packaging with proof-of-purchase documentation enclosed and a Return Merchandise Authorization (RMA)
number printed clearly on the outside of the shipping container. RMA numbers are obtained by contacting Customer Support.
This warranty does not apply to any product determined by SureCall to have been subjected to misuse, abuse, neglect, or
mishandling that alters or damages the product’s physical or electronic properties.
For complete warranty text, including limitations and liability, see the Fusion4Home full user manual, available online.
Have questions?
We have answers! Reach out to our US-based support team:
Call: 1-888-365-6283
Email: [e-mail]
Visit: www.surecall.com/support to download the user manual for:
» Detailed setup instructions  Troubleshooting tips » Warranty information
Power Supply Coax Cable - (50 ft. RG6 &
20 ft. SC-240)
Outside Antenna -
Directional Yagi
Inside Antenna -
Directional Panel
Booster
If you Want to Improve Coverage
1. Find a location that receives a stronger signal and relocate the outside antenna to that location.
2. Optimize the Yagi antenna angle.
3. Increase the distance between the outside and inside antenna.
4. Set each dial on the booster to maximum gain.
LED Indicators
Color Condition Indication
OFF
This is part of normal operation. Light is o while band is active.
Yellow Solid
This is part of normal operation. Indicates that the band is Inactive. After a period of time, if there’s
no activity the band will go into sleep mode. Light is o while band is active.
Yellow Flashing
This is part of normal operation. Indicates that the Automatic Gain Control (AGC) is self-adjusting.
Red Flashing Indicates that the booster is receiving too much signal which could cause the aected band to
automatically turn o. When this happens:
1. For kits using an OMNI outside antenna, relocate the outside antenna to a location where the signal
is weaker.
2. For kits using a YAGI outside antenna, turn the antenna in short increments away from the signal source.
3. Increase the separation between antennas (additional vertical separation works best).
4. Add an inline attenuator to the cable coming into the outside port of the booster.
5. As a last resort, turn down the dB gain on the dial until the light goes OFF or ashes yellow.
Yellow/
Red
Alternately
Flashing
Oscillation is detected.
First, try increasing the separation between the inside and outside antennas. If your booster kit uses
two directional antennas (example: outside Yagi antenna and inside panel antenna), ensure that they
are facing away from one another.
If oscillation continues, lower the dB gain in small increments until the light turns o or ashes yellow.
Red Solid Band is o.
If a red light has been ashing for an extended time, the band will automatically shut o and display a
solid red light.
This can also happen when the booster attenuation has been turned all the way down.
WARNING: Do not attenuate the uplink and downlink dB settings below 35dB. This could cause the aected frequency band to turn o.
SureCall Fusion4Home
™
Yagi / Panel Kit