User Guide EZ Connect Single Band Consumer Booster
Table of Contents Overview 4 Before Installation Contents 4 Installation 4 Before installation Step 1 6 Step 2 7 System configuration Step 4 4 4 7 9 Product specifications 8 Regulatory Information 8
Chapter 1 Introduction 1.2 In the Box Remove Contents from packaging • • • • • • Receiving Unit Receiving Cable RG-174 (30’) Inside Antenna Inside Cable RG-174 Cable (10 ft) Power Injector Power Supply 1.3 System Requirements Download the SureCall EZ Connect app for easy installation 1.4 • • • • • • 1.
1.6 How it works 1. 2. 3. The receiving unit is used to communicate with your Verizon tower. It is placed in the area of best signal and aimed toward the tower in order to pick up the strongest signal. The receiving unit also amplifies the received signal and sends it to the inside panel antenna. The inside panel antenna broadcasts the signal to your mobile devices and then back to the cell tower. Chapter 2 Before Installation 2.
2.2 Identify Optimal placement for EZ Connect Scan and download the SureCall app to pair with your EZ Connect. Use the app to see real time feedback to guide you to the best placement for both components. 2.2.1 Receiving Unit Identify window location facing your closest tower that receives the strongest signal. 20’ separation is recommended when receiving unit is outside 30’ separation is recommended when receiving unit is placed inside 2.2.
Chap pter 3 Installa I ation 3.1 Mount Receiving R g Unit Multiple mounting m optionss are provided: Roof R mount (reccommended), w wall mount and Window W mount Option 1: Roof Mo ount ount Option 2: Wall Mo Option 3: Window w mount Once you u have determ mined the insid de location with h the strongesst signal, place e the receiving g unit in that lo ocation. 3M tape is prrovided for mo ounting on win ndow surface.
3.2 Mount inside antenna Choose to set on a desktop or mount to a wall. Receiving Unit Indoor Panel Antenna Refer to app to check for isolation issues Chapter 4 System Configuration 4.1 Recommendations for improving install Inside antenna should be 30’ (line of sight) Window-Mount / outside unit Confirm the inside antenna is pointing away from the Window-Mount / outside unit.
Chapter 5 Troubleshooting If the booster isn't receiving enough power or isn't working properly, the LED light on the power supply will be red instead of green Chapter 6 Product specifications Name EZ Connect Model: SC-EZ-Connect Certifications: FCC (North America) Parameter Type Single band Bands Supported 13 Uplink(776-787MHz) System Gain(dB) 64 Max Output Power(dBm) 25 Outdoor Antenna Gain(dBi) 5 EIRP(dBm) 30 Noise Figure(dB) 5 Downlink(746-757MHz) System Gain 71 Active Gain(dB) 7
Operating Temperature -10~55Ԩ Host size (H x W x L, in) 8¼xWx2¼ Host installation Pole, Wall Coax Cable (connected to booster) 30 ft RG-174, SMA Connector Waterproof level of host IP66 or higher Host LED TBD Power box RF Connector SMA Coax Cable (power injector to inside antenna) 10' RG174 White With SMA Connector Power port DC 2.
2.3 Regulatory Information THIS IS A CONSUMER DEVICE BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 Inches) from any person.
Antenna kitting: Component Prod No. Description Gain/Loss Notes LTE-V Outdoor Antenna* SC548-1W 5dBi Indoor Cable* Power box10Feet 4dB Indoor Antenna* SC548-2W 5dBi Default Matching Antenna * All equivalent antennas and cables are suitable for use with the EZ Connect booster.