www.supremainc.com BioLite NET Innovative Fingerprint Terminal User guide((ver ver 1.0 )1.
Product Contents Basic Contents Product Contents E-ring Main Body Default Sub bbracket c e (optional) Wall-mounting metal bracket z Recommended power supply 12V ±10%, at least 2500mA for BioLite-NET alone installation. Comply with standard IEC/EN 60950-1 (CE Certification). To share the power with other devices, use a power supply with higher current ratings. Shrinking Tube 12V power adaptor (optional) Before Start 2 ⒸCopyright 2008 Suprema Inc.
Cable spec.
Power Connection Recommended power supply 12V ± 10%, at least 1000mA. z To share the power with other devices, use a power supply with higher current ratings. z 4 ⒸCopyright 2008 Suprema Inc.
Relay Connection – Fail safe lock 5 ⒸCopyright 2008 Suprema Inc.
Relay Connection – Fail secure lock 6 ⒸCopyright 2008 Suprema Inc.
Relay Connection - Automatic door 7 ⒸCopyright 2008 Suprema Inc.
Door switch connection BioLite NET 1 Door Status 4 (1) SW0 Input (PURPLE) (2) SW0 GND (GRAY) (3) SW1 Input (BROWN) (4) SW1 GND (GRAY) Request q To Exit 8 ⒸCopyright 2008 Suprema Inc.
Switch connection (Alarm, Emergency switches) 9 ⒸCopyright 2008 Suprema Inc.
RS485 connection for host communication 10 Before Start ⒸCopyright 2008 Suprema Inc.
RS485 connection for Secure I/O (1) Power 12V (Red) (2) Power GND (Black) (3) Signal GND (White) (4) TRX+ (Blue) (5) TRX- (Yellow) Power Power BioLite NET (Master) *Enable termination ((optional, ti l see Note1) N t 1) (1) Power 12V (Red) ((2)) Power GND ((Black)) (3) Signal GND (White) (4) TRX+ (Blue) (5) TRX- (Yellow) BioLite NET (Slave) TRX GND TRX+ TRXSecure I/O TRX GND TRX+ TRX- ...
Installation Reference - Stand alone 12 ⒸCopyright 2008 Suprema Inc.
Installation Reference – Using Secure I/O, 2 door RTE switch Switch 0 Internal Relay RS485 Secure I/O Relay 0 Door 1 Door 0 Door Status RTE switch Switch 0 Switch 1 Switch 1 Door Status 13 ⒸCopyright 2008 Suprema Inc.
ⒸCopyright 2008 Suprema Inc.
Installation Reference – Using RFID card item Model Transmit Receive Modulation Communication Channel Mode content ( ) BioLite-NET(BLN-OC) 13.56MHz 13.56MHz ASK Single propagation Single channel 1:1 Using RFID card (13.56MHz = Mifare model only) In case 1:1 mode is set as RF Card z If the 1:1 mode is set as Card Only, user can access just by placing the card to BioLite-NET without any additional procedure. z 15 ⒸCopyright 2008 Suprema Inc.
Installation Reference – LAN RTE switch Switch 0 Network hub Ethernet RS485 Secure I/O Relay 0 Door 1 Switch 1 Door Status If you select Network on initial UI menu, Network Setup menus appear on the display. If you select TCP/IP on network menu, following menus appear on the display. LAN TYPE z z Max conn SSL z z z z z DHCP z z IP Address, gateway, subnet z Setting : Disable/Ethernet Used when connected to PC via Ethernet using RJ45 connector on the rear of the device.
Electrical Specification Min. Typ. Max. Notes 10 8 10.8 12 13 2 13.2 Use regulated DC power adaptor only Power Voltage (V) Current (mA) - 250 RTC Battery Voltage (V) Current (mAH) 2.7 3 - 3.3 Lithium-ion rechargeable battery 11 Switch Input VIH (V) - TBD VIL (V) - TBD Pull-up resistance (Ω) - 4.7k - VOH (V) - 5 - VOL (V) - 0.8 - Pull-up resistance (Ω) - 4.7k - Switching capacity (A) - - 1 0.3 Switching power (resistive) - - 30W 37.
ⒸCopyright 2008 Suprema Inc.
Troubleshooting Fingerprint can not be read well or it takes too long. z z z Fingerprint is entered but authorization keeps failing. z z z Check whether the time is set as lock time. time Check whether an antipass back mode is in use. In antipass back mode, only who entered can exit. Device doesn’t operate though power is connected.
FCC Rules 20 ⒸCopyright 2008 Suprema Inc.
Tel : 82-31-710-2400 Fax : 82-31-783-4506 21 ⒸCopyright 2008 Suprema Inc.