BioLite N2 USER GUIDE Version 1.08 English EN 102.00.BLN2 V1.
Contents Safety Instructions................................................................................. 4 Introduction ............................................................................................ 6 Components ...................................................................................................................................................6 Name and function of each part .....................................................................................................
Checklist before reporting a failure ........................................................................................................24 Product Specifications ......................................................................... 25 Dimensions ...................................................................................................................................................26 FCC compliance information ...............................................................
Safety Instructions Safety Instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance of instructions could lead to serious injury or death. Installation Do not install the product in a place with direct sunlight, moisture, dust, or soot. • A fire or electric shock may occur. Do not install the product in a place with heat from an electric heater. • A fire or electric shock may occur due to overheating.
Safety Instructions Operation Do not drop the product or apply an impact to the product. • A product failure may occur. Manage the password with care not to disclose it to others and change the password periodically. • Otherwise, illegal intrusion may occur. Do not press the buttons on the product forcibly or using a sharp tool. • A product failure may occur. Be careful not to contaminate or damage the fingerprint contact unit with a dirty hand or foreign substances.
Introduction Introduction Components BioLite N2 Wall Bracket Shrink Tube 120 Ω resistor Ferrite Core NOTE Diode Drilling Template PVC Anchor x2 Bracket Fixing Screw (Star Shaped) Fixing Screw x2 Quick Guide Open Source Software Guide • Components may vary according to the installation environment. • For additional content regarding product installation, access the Suprema website (www.suprema.co.kr) and view the installation guide.
Introduction Name and function of each part LCD screen Function button Keypad ESC button OK button Fingerprint authentication unit RF card authentication unit Cable Speaker Name Description LCD screen Provides UI for operation. Function button Used for T & A key or changing a letter. Keypad • • 0 ~ 9: Used for entering a number or letter. , , , : Used for moving to the desired item. OK button Used for selecting and setting T&A Mode.
Introduction Cables and connectors Pin 8 Name Color 1 PWR +VDC Red 2 PWR GND Black (White stripe) 3 485 TRXP Blue (White stripe) 4 485 TRXN Yellow (Black stripe) 5 485 GND White (Black stripe) 6 ENET RXN Yellow 7 ENET RXP Green 8 ENET TXN Red 9 ENET TXP Black 10 RLY NO Gray (White stripe) 11 RLY COM Green (White stripe) 12 RLY NC Orange (White stripe) 13 WG D0 Green 14 WG D1 White 15 TTL GND Gray 16 TTL IN 1 Brown 17 TTL IN 0 Purple
Introduction How to enroll a fingerprint correctly In order to improve the fingerprint authentication rate, enroll the fingerprint correctly. BioLite N2 can recognize a fingerprint even if the angle and position of a user's fingerprint input change. If you enroll a fingerprint with attention to the following matters, the authentication rate can be improved.
Admin Menu Admin Menu All Menus 1 2 Press ESC and authenticate with the Admin level credential. Select the desired menu. NOTE • If the administrator has not been designated, the menu screen will be displayed when you press ESC.
User User Registering user information The user information including fingerprints can be registered. 1 2 3 Press ESC and authenticate with the Admin level credential. Select USER > Add User, then press Select the desired item, then press and set or . When you press OK, the user information will be registered. User ID: Enter a number between 1 and 429467295 to register as the user ID.
User Modifying user information User Management or Administrator can modify the registered user information. A fingerprint or card can be added, and PIN and level can be modified. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select USER > Search User, then press . Select your search terms. You can search for a user by All, User ID, User Name, Fingerprint, or Card. . Modify the information by referring to Registering user information.
Auth Auth Mode Fingerprint Mode You can set the schedule to be used for each authentication method using a fingerprint. 1 2 3 Press ESC and authenticate with the Admin level credential. Select AUTH > Auth Mode > Fingerprint Mode, then press . Select the desired item and set the schedule by pressing or : Mode to use a fingerprint only. • + • 4 . : Mode to authenticate with a fingerprint and then enter a PIN. To save settings, press OK. NOTE • A schedule can be set in BioStar 2.
Auth NOTE • A schedule can be set in BioStar 2. If there is no set schedule, only Not Used and Always can be selected. • For detailed contents regarding setting a schedule, refer to BioStar 2 Administrator's manual. ID Mode You can set the schedule to be used for each authentication method using ID. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select AUTH > Auth Mode > ID Mode, then press . Select the desired item and set the schedule by pressing or .
Auth Job Code: Select whether or not to use Job Code. • 4 To save settings, press OK. NOTE • When Enabled is set for Job Code, you can change the user job code. You can select the desired job code by pressing OK long and authenticating. Fingerprint You can change settings regarding the fingerprint authentication. 1 2 3 Press ESC and authenticate with the Admin level credential. Select AUTH > Fingerprint, then press Select the desired item and then change the settings by pressing or .
Auth Server Matching When you set Server Matching, the user authentication is not carried out in the device, but rather in BioStar. Server Matching can be useful when there is a large amount of user information in the device or you do not wish to publicly expose the device where user credential information is saved. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select AUTH > Server Matching, then press Change the settings by pressing or . . To save settings, press OK.
Display Display You can change the display settings of the device. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select DISPLAY, then press . Select the desired item and then change the settings by pressing • Home Screen: Change the style of the home screen. • • or . • Backlight Timeout: Set the time (second) to turn off the lighting of LCD screen. Menu Timeout: Set the time (sec) for the menu screen to disappear automatically.
Device Device Date & Time You can set date and time. Set the date and time accurately in order to collect accurate log data. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select DEVICE > Date & Time, then press . Select the desired item and then change the settings by pressing or . • • Date: Check the current date. To modify it directly, set Disabled for Time Sync. Time: Check the current time. To modify it directly, set Disabled for Time Sync.
Device Device Info You can view the model name, firmware version of Device ID and MAC address. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select DEVICE > Device Info, then press . You can view the information including Model Name, Device ID, HW, FW, Kernel and MAC. To return to the previous screen, press ESC. Memory Usage You can view the status of memory usage. 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select DEVICE > Memory Usage, then press .
Device Restore Default Device settings, network setting, and operator levels will be reset. 1 2 3 Press ESC and authenticate with the Admin level credential. Select DEVICE > Restore Default, then press . • • Reset All Settings: You can reset all settings stored on the device. Press OK to reset all device settings. To cancel, press ESC. Quick Reset: You can reset all settings except network settings. Press OK to reset all settings except network settings. To cancel, press ESC.
Network Network Network Settings You can change the network settings of the device. TCP/IP 1 2 3 4 Press ESC and authenticate with the Admin level credential. Select NETWORK > TCP/IP, then press . Select the desired item and then change the settings by pressing or . • Port: Set the device port. • • • DHCP: Set whether or not to use DHCP. If Disabled is set, the user can modify Port, IP Address, Gateway, or Subnet Mask. IP Address: View the IP address of the device.
Network Serial Settings RS-485 1 2 3 Press ESC and authenticate with the Admin level credential. Select NETWORK > RS-485, then press • Mode: Select the RS-485 mode. • Baud Rate: Select the desired baud rate. . To save settings, press OK.
Event Log Event Log Search Log You can set a condition and search a log. 1 2 3 4 5 Press ESC and authenticate with the Admin level credential. Select EVENT LOG > Search, then press . Select the desired item and then change the settings by pressing To return to the previous screen, press ESC. You can delete all saved logs. Press ESC and authenticate with the Admin level credential. Select EVENT LOG > Delete All Logs, then press . To delete all logs, press OK. To cancel, press ESC.
Troubleshooting Troubleshooting Checklist before reporting a failure Category Power Problem The power is being supplied but the device does not operate. I lost my PIN. PIN I entered my PIN and pressed the OK button, but I still cannot open the door. The fingerprint has been enrolled but fingerprint authentication cannot be done smoothly and errors occur frequently. Fingerprint Suddenly fingerprint authentication cannot be done. Door Lock The door cannot be locked when I close the door.
Product Specifications Product Specifications Category Feature Biometric Specification Fingerprint • Credential RF Option • • RF read range* MIFARE/DESFire/ISO15693: 50 mm, EM/FeliCa: 30 mm CPU 1.2 GHz Memory 4GB Flash + 64Mb RAM LCD type 1.
Product Specifications Dimensions (Unit: mm) 58 34 190 44 180.3 171.5 47.
FCC compliance information FCC compliance information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Appendices Appendices Disclaimers • The information in this manual is provided with regard to the Suprema's products. • The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
Appendices When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
Appendices case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
Appendices • regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
Appendices 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law.
Appendices organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
Appendices The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
Appendices 1. Exception to Section 3 of the GNU GPL. You may convey a covered work under sections 3 and 4 of this License without being bound by section 3 of the GNU GPL. 2. Conveying Modified Versions.
Appendices version for the Library. OpenSSL License Copyright (c) 1998-2017 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Appendices LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.
Suprema Inc. 16F Parkview Tower, 248, Jeongjail-ro, Bundang- gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA Tel: +82 31 783 4502 I Fax: +82 31 783 4503 I Inquiry: sales@supremainc.com ©2019 Suprema Inc. Suprema and identifying product names and numbers herein are registered trade marks of Suprema, Inc. All non-Suprema brands and product names are trademarks or registered trademarks of their respective companies.
