BioEntry W2 INSTALLATION GUIDE Version 1.29 English EN 101.00.BEW2 V1.
Contents Safety Instructions ................................................................................. 3 Introduction ........................................................................................... 5 Components ...................................................................................................................................................5 Name and function of each part .....................................................................................................
Safety Instructions Safety Instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance of instructions could lead to serious injury or death. Installation Do not install the product in a place with direct sunlight, moisture, dust, or soot. • A fire or electric shock may occur. Do not install the product in a place with heat from an electric heater. • A fire or electric shock may occur due to overheating.
Safety Instructions Operation Do not drop the product or apply an impact to the product. • A product failure may occur. Be careful not to contaminate or damage the fingerprint contact unit with a dirty hand or foreign substances. • Deterioration in fingerprint authentication performance and a product failure may occur. When cleaning the product, wipe the product with a soft and dry cloth and no water, benzene or alcohol. • Otherwise, a product failure may occur.
Introduction Introduction Components PVC Anchor (2 EA) Fixing Screw (2 EA) NOTE • BioEntry W2 Wall Bracket 120 Ω resistor Ferrite Core Diode (1 EA) Shrink Tubes Drilling Template Quick Guide Components may vary according to the installation environment.
Introduction Name and function of each part LED Indicator Network reset button RF card authentication unit LED status indicator for Network Cable Fingerprint authentication unit Name LED Indicator RF card authentication unit Fingerprint authentication unit Feature Indicates the operational status of the device with the color of the LED.
Introduction Cables and connectors Pin NOTE • Name Color 1 RLY NO Gray (White stripe) 2 RLY COM Green (White stripe) 3 RLY NC Orange (White stripe) 4 VB2 5 VB1 6 WG D0 Green 7 WG D1 White 8 WG GND Black 9 TTL IN 1 Brown 10 TTL IN 0 Purple 11 PWR +VDC Red 12 Not Connected Pink 13 PWR GND Black (White stripe) 14 485 TRXN Yellow (Black stripe) 15 485 TRXP Blue (White stripe) 16 485 GND White (Black stripe) 17 ENET TXP White 18 ENET TXN Orange 19 ENET RX
Introduction How to enroll a fingerprint In order to improve the fingerprint authentication rate, register the fingerprint correctly. BioEntry W2 can recognize a fingerprint even if the angle and position of a user's fingerprint input change. If you register the fingerprint with attention to the following matters, the authentication rate can be improved.
Installation Installation Fixing the bracket and the product 1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where BioEntry W2 will be installed. NOTE • • • If installing BioEntry W2 on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws. To avoid RF interference, a minimum separation distance must be maintained.
Installation 2 Install BioEntry W2 onto the fixed bracket. 3 Assemble BioEntry W2 with the bracket by rotating the product fixing screw. NOTE • When assembling the product with the bracket, you can use the included bracket fixing screw(Star Shaped) instead of the product fixing screw for enhanced security.
Installation Power supply connection BioEntry W2 11 - PWR +VDC 13 - PWR GND NOTE • • • • • • • AC OK Battery Low • • • • • Battery Low Alarm Red Black (White stripe) Listed Class 2 power unit shall be recommended to use. The unit is powered by external Listed Class 2 power supply with 12VDC or by Listed to UL 294B PoE power source. For ULC S319 compliance, connect PSC-100A power supply and Casil CA 1270 battery.
Installation Network connection TCP/IP LAN connection (connecting to a hub) You can connect the product to a hub using a general type CAT-5 cable. Hub PC BioEntry W2 LAN connection (connecting to a PC directly) BioEntry W2 has an automatic MDI/MDIX function so that it can be connected to a PC directly using a normal straight type CAT5 cable, not a cross cable.
Installation TTL input connection 9 - TTL IN 1 10 - TTL IN 0 16 - 485 GND Door sensor Brown Purple White (Black stripe) 16 9 16 10 BioEntry W2 Door button 13
Installation Relay connection Fail Safe Lock In order to use the Fail Safe Lock, connect N/C relay as shown in the figure below. There is normally a current flowing through the relay for the Fail Safe Lock. When the relay is activated, blocking the current flow, the door will open. If the power supply to the product is cut off due to a power failure or an external factor, the door will open.
Installation Automatic door connection Door button Sensor 1 Automatic door Controller 2 Door Lock 1 2 - RLY NO - RLY COM Gray (White stripe) Green (White stripe) BioEntry W2 15
Installation Connecting as a standalone BioEntry W2 can be connected to the door lock, door button, and door sensor directly without connecting a separate I/O device.
Installation Connecting to Secure I/O 2 Secure I/O 2 is an I/O device, can be connected to BioEntry W2 with the RS-485 cable. Security can be maintained even if the connection between BioEntry W2 and Secure I/O 2 has been lost or the power supply to BioEntry W2 has been shut off due to external factors. • Use an AWG24 twisted pair with a maximum length of 1.2 km for the RS-485 cable.
Installation Wiegand connection 6 7 8 8 7 - WG D0 - WG D1 - WG GND Green White Black 8 7 RFID reader 6 Control device 6 BioEntry W2 BioEntry W2 Use as a Wiegand input device Use as a Wiegand output device Resetting Network Settings 1 2 3 4 5 Turn the power on. Press the network reset button on the rear of device until the device restart automatically. Connect the device with default values. • TCP/IP address: DHCP address assignment (If DHCP address assignment is failed, 169.254.x.
Product specifications Product specifications Category Feature Biometric RF Option Credential NFC BLE General RF read range * CPU Memory LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Dimension (W x H x D) Weight Fingerprint Capacity Interface IP rating IK rating Certificates Image dimension Image bit depth Resolution Template Extractor / Matcher LFD Max. User (1:1) Max. User (1:N) Max. Template (1:1) Max. Template (1:N) Max.
Product specifications * Access control feature (UL294 specification) Destructive attack - level2, Line security - level2, Endurance - level1, Standby power- level1 20
Product specifications Dimensions (Unit: mm) 38.2 50 172 172 43.5 39.4 156.
FCC Compliance Information FCC Compliance Information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Appendices Appendices Disclaimers • The information in this manual is provided with regard to the Suprema's products. • The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
Appendices When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
Appendices case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
Appendices • regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
Appendices 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law.
Appendices organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
Appendices The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
Appendices 1. Exception to Section 3 of the GNU GPL. You may convey a covered work under sections 3 and 4 of this License without being bound by section 3 of the GNU GPL. 2. Conveying Modified Versions.
Appendices version for the Library. OpenSSL License Copyright (c) 1998-2017 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Appendices LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.
'$$ DPNQMJBODF JOGPSNBUJPO compliance information Copyright notice The copyright of this document is vested in Suprema. The rights of other product names, trademarks and registered trademarks are vested in each individual or organization that owns such rights.
Appendix Escape clause x The information in this manual is provided with regard to the Suprema's products. x The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
