www.supremainc.com INSTALLATION GUIDE BioEntry R2 English Version 1.00 EN 101.00.BER2 V1.
Contents Safety instructions............................................................................................ 3 Introduction ...................................................................................................... 5 Components ...................................................................................................................................................5 Name and function of each part ................................................................................
Safety instructions Safety instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance of instructions could lead to serious injury or death. Installation Do not install the product in a place with direct sunlight, moisture, dust, or soot. • A fire or electric shock may occur. Do not install the product in a place with heat from an electric heater. • A fire or electric shock may occur due to overheating.
Safety instructions Operation Do not drop the product or apply an impact to the product. • A product failure may occur. Be careful not to contaminate or damage the fingerprint contact unit with a dirty hand or foreign substances. • Deterioration in fingerprint authentication performance and a product failure may occur. When cleaning the product, wipe the product with a soft and dry cloth and no water, benzene or alcohol. • Otherwise, a product failure may occur.
Introduction Introduction Components PVC anchor (2 EA) BioEntry R2 Connection cable (2 pins 1 EA, 3 pins 1 EA) Diode (1 EA) Wall bracket Fixing screw (2 EA) Ferrite core (1 EA) 120 Ω resistor (1 EA) Drilling template Quick guide Note Components may vary according to the installation environment.
Introduction Name and function of each part LED lamp RF card authenticatio unit Fingerprint authentication unit Power supply (2 pins) RS-485 (4 pins) Name Description LED lamp Indicates the operational status of the product with the color of the LED lamp. RF card authentication unit Reads RF cards for entering and exiting. Fingerprint authentication unit Reads fingerprints placed on it for entering and exiting. Power supply (2 pins) Connect the power supply cable.
Introduction Cables and connectors Power supply Pin Name Color 1 2 PWR +VDC PWR GND Red (white stripe) Black (white stripe) Pin Name Color 1 2 3 4 485 TRXP 485 TRXN 485 GND SH GND Blue Yellow Black Gray RS-485 7
Introduction How to enroll a fingerprint In order to improve the fingerprint authentication rate, register the fingerprint correctly. BioEntry R2 can recognize a fingerprint even if the angle and position of a user's fingerprint input change. If you register the fingerprint with attention to the following matters, the authentication rate can be improved.
Installation Installation Fixing the bracket and the product 1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where BioEntry R2 will be installed. Note • • If installing BioEntry R2 on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws. To avoid RF interference, a minimum separation distance must be maintained.
Installation 2 Install BioEntry R2 onto the fixed bracket. Wall 3 Connect BioEntry R2 to the bracket by rotating the product fixing screw.
Installation Connecting the cables Power supply connection 1 - PWR +VDC Red (white stripe) 2 - PWR GND Black (white stripe) BioEntry R2 UPS (Optional) DC power RS-485 connection 1 - 485 TRXP 2 - 485 TRXN 3 - 485 GND 4 - SH GND Blue Yellow Black Gray Note • • • • • Use a power supply adaptor of DC 12 V (± 10%) with a minimum of 1,500 mA which has obtained the approval of IEC/EN 60950-1.
Installation Restoring the Factory Defaults This will delete all data and root certificate on the device and reset the settings. 1 2 3 Turn the power on. Press the reset button three times quickly. When the yellow LED is blinking, press the reset button again. Note • If there is no root certificate on the device, you cannot restore the factory defaults.
Product specifications Product specifications Category Credential General Interface Electrical BER2-OD Biometric LF 카드 Fingerprint EM HF 카드 MIFARE, MIFARE Plus, DESFire/EV1, FeliCa NFC 카드 RF read range * CPU Memory LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Dimension (W x H x D) 지원 MIFARE/DESFire/EM/HID Prox/iCLASS : 50 mm, FeliCa: 30 mm 1.
Product specifications Dimensions (Unit: mm) * The tolerance is ±0.3mm. 164 50 37.5 149.8 40.
FCC compliance information FCC compliance information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Appendices Appendices Disclaimers • The information in this manual is provided with regard to the Suprema's products. • The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
Appendices To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received.
Appendices System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work.
Appendices • • • • Corresponding Source fixed on a durable physical medium customarily used for software interchange.
Appendices • • e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
Appendices In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
Appendices WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 17.
Appendices • • • c) For a Combined Work that displays copyright notices during execution, include the copyright notice for the Library among these notices, as well as a reference directing the user to the copies of the GNU GPL and this license document.
Appendices This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL.
www.supremainc.com www.supremainc.
