User's Manual

ManualsBrandsSuperior Electronics ManualsElectronicsRemote Control Transmitter

Installation Manual

Three- and Four-Channel RF Receivers

The

910R3Q

and SK

910R4Q are wireless

receiver

that

meet the growing demand for multi

channel receiver

with

multiple and independently controlled output modes. RF receivers can be used to control a variety of home automation

devices such as garage door openers, lights, motorized gates, lifts, or other devices remotely.

These receivers are compatible with both fixed code and code hopping transmitters. Code hopping transmitters, such as

SECO-LARM CODEBUMP™ transmitters, change codes every time transmitter sends a signal for extra security. See page 4

of this manual for a list of compatible transmitters.

Mount

the receiver

out of sight in a location where it is not exposed to the weather or moisture

, and

where it is not

surrounded by metal. Metal will block the RF signal, resulting in a reduced range.

2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives interference from local RF

activity (e.g., an airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.

Installation Notes

Introduction:

•

Flexible operating voltage: 11~24 VAC/VDC

• Independently programmable channels

• Compatible with all SECO-LARM transmitters

Note: Operating range will vary greatly depending on the installation and operating environment.

Also Available from SECO

LARM:

This manual covers only

the three

and four

channel receiver

. For information on

all other receivers

, please contact SECO

LARM

910R

................................

...............................

One

channel receiver, 315MHz

SK-910RLQ ........................................... Low-voltage, one-channel receiver, 315MHz

SK-910RVQ ......................................................... Low-voltage, one-channel receiver,

transistor ground output 315MHZ

SK-910R-4Q ......................................................... One-channel receiver, 433.92MHz

SK-910RL-4Q ................................... Low-voltage, one-channel receiver, 433.92MHz

SK-910RV-4Q ...................................................... Low-voltage, one-channel receiver,

transistor ground output, 433.92MHz

SK-910RB2Q ............................................................. Two-channel receiver, 315MHz

SK-910RB2-4Q ..................................................... Two-channel receiver, 433.92MHz

(SK

910R4Q pictured)

910R3Q

3 Channels (315MHz)

910R3

3 Channels (433.92MHz)

910R4Q

4 Channels (315MHz)

910R4

4 Channels (433.92MHz)

Summary of content (4 pages)

PAGE 1
Installation Manual SK-910R3Q SK-910R3-4Q SK-910R4Q SK-910R4-4Q 3 Channels (315MHz) 3 Channels (433.92MHz) 4 Channels (315MHz) 4 Channels (433.92MHz) (SK-910R4Q pictured) Three- and Four-Channel RF Receivers • Flexible operating voltage: 11~24 VAC/VDC • Independently programmable channels • Compatible with all SECO-LARM transmitters Note: Operating range will vary greatly depending on the installation and operating environment. Also Available from SECO-LARM: SK-910RBQ ..................................
PAGE 2
ENFORCER Three- and Four-Channel RF Receiver Code Learning a New Transmitter Button: Each receiver channel can learn the codes of up to 15 different transmitters on a first-in, first-out basis. Below is the procedure for code learning a new transmitter button. The same procedure applies to each of the receiver’s channels. 1. Press the transmitter programming button of the desired channel to be programmed for 3 seconds or more.
PAGE 3
ENFORCER Three- and Four-Channel RF Receiver Overview: CH 3 Mode switch CH 2 Mode switch CH 1 Mode switch CH 4 Mode switch (4-Channel models only) Programming mode switch Time programming DIP switch Power Input 11~24 VAC/VDC Channel 1 Channel 2 Sec.
PAGE 4
ENFORCER Three- and Four-Channel RF Receiver Sample Applications: Negative Output Positive Output COM NC NO Positive Power Source — + Negative Power Output — + Power for receiver Power for receiver Typical N.O. Application Typical N.C. Application COM NC NO SD-996C-NUQ Electric Door Strike COM NC NO E-941SA-1200 Electromagnetic Lock — + — + N.C. Application with Independent Power Sources N.O.