User's Manual

ENFORCER Two-Channel RF Receiver
4 SECO-LARM U.S.A., Inc.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the
device.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the
written permission of SECO-LARM.
SECO
SECOSECO
SECO-
--
-LARM
LARMLARM
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]
Operating frequency
SK-910RBQ/SK-910RB2Q
315MHz
SK-910RB-4Q/SK-910RB2-4Q
433.92MHz
Memory capacity
15 transm
itter button codes
per channel
Operating voltage
11~24 VAC/VDC
Operating current
Standby
8mA@12VDC
Active
3
0mA@12VDC per channel
Relay contact rating
Form C 10A@24VDC or 120VAC per channel
Connectors
Screw terminals, +,
-
, with NO/NC/COM per channel
Dimensions
3
1
/
8
”x2
9
/
16
”x1” (80x65x25mm)
Sample Applications
:
Specifications
:
Compatible Transmitters
:
315MHz
433.92MHz
Fixed Code: 68 billion codes
SK
-
919 Series Fixed Code
SK
-
939 Series Fixed Code
CODEBUMP™: 18 quintillion (1.8x10
19
) codes
SK
-
917 Series CO
DEBUMP
SK
-
937 Series CODEBUMP
N.O. Application with Independent Power Sources
COM
NC
NO
—
+
DC Power
Source
AC Power
Source
SD
-
996C
-
NUQ
Electric Door Strike
N.C. Application with Independent Power Sources
DC Power
Source
COM
NC
NO
—
+
AC Power
Source
E
-
941SA
-
1200
Electromagnetic Lock
Typical N.C. Application
COM
NC
NO
—
+
E
-
941SA
-
1200
Electromagnetic Lock
Typical N.O. Application
SD
-
996C
-
NUQ
Electric Door Strike
COM
NC
NO
—
+
Negative Output
COM
NC
NO
—
+
Negative Power Source
Negative Power Output
Power for SK
-
910RBQ
/
SK
-
910RB2Q
Positive Output
COM
NC
NO
—
+
Positive Power Source
Positive Power Output
Power for SK
-
910RBQ
/
SK
-
910RB2Q
MiSK
-
910RBxQ_
S
K
-
9
1
9
T
2
A
_
M
u
F
C
C
_
1
2
1
1
.docx
Part #: 762-116-2%
PITSW1
F
C
C
I
D
:
K
4
E
9
1
9
T
P
2
A
This manual covers only
one
-
and
two
-
channel receivers. For information four
-
channel recei
vers, please contact SECO
-
LARM.
Installation Manual
One
-
and
Two
-
Channel RF Receiver
s
The SK
-
910RBQ
and
SK
-
910RB2Q
are
wireless
receiver
s
that meets the growing demand for
receivers with multiple and independently controlled output functions. These RF receivers are
compatible with both code hopping and fixed code transmitters (see page 4 of this manual for a list of
compatible transmitters). The receivers can be used to control a variety of home automation devices
such as garage door openers, lights, motorized gates, lifts, or other devices remotely.
1.
Mount the receiver out of sight in a location where it is not exposed t
o weather or moisture, and
where it is not surrounded by metal. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives
interference from local RF activity (e.g., an airport or military base), the antenna wire can be folded.
IMPORTANT: DO NOT CUT THE ANTENNA WIRE.
Insta
llation Notes
:
Introduction:
SK-910RBQ (315MHz)
SK-910RB-4Q (433.92MHz)
SK-910RB2Q (315MHz)
SK
-
910RB2
-
4Q
(433.92MHz)
•
Flexible operating voltage: 11~24 VAC/VDC
• Up to 500ft (152m) range
• Independently programmable channels
Also Available from SECO
-
LARM:
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
SK
-
910RLQ
................................
...........
Low
-
voltage, one
-
channel receiver, 315MHz
SK-910RVQ ......................................................... Low-voltage, one-channel receiver,
transistor ground output 315MHZ
SK-910RL-4Q ................................... Low-voltage, one-channel receiver, 433.92MHz
SK-910RV-4Q ...................................................... Low-voltage, one-channel receiver,
transistor ground output, 433.92MHz
*
*
SK-910RB2Q shown